Voto Manufacturers Sales Co.

Gr-30 Chain is commonly called Proof Coil and is manufactured to meet ASTM & NACM specifications. Typical uses include barrier chains, trailer safety chains, light construction, marine industry, etc. Gr-30 is available in a wide assortment of finishes and packaged configurations. •Meets ASTM & NACM standards •Permanent identification on chain •100% proof tested IMPORT

Gases: Natural or Propane Capacity: 1, 500, 000 Btuh maximum 850, 000 Btuh minimum Orifice Size: 41 DMS (X46) Blower: 7, 000 cfm Electrical Rating: 115 volts, 60 Hz, 9.4 amps, Single Phase Min. Temperature Rating: Minus 40 degrees F Gas Supply: Inlet Pressure Manifold Pressure Max W.C. Min W.C. Max W.C. Min.W.C. Propane 14" 9" 2.7" 0.75" Natural 14" 9" 7.2" 2.0" (Minimum inlet pressure is for purpose of input adjustment) Page 6 S1505B Manual 974-9308 Rev. 4.21; Aug 8 2008 Installation The Sure Flame Model S1505B is a direct fired gas heater

This product requires custom shipping Allis Chalmers Svedala H-4000 Hydrocone Fits Sandvik H4800 and CH440 Crushers Old 44.400.066.001 Factory no. 442.8418.02 ESCO GAC4000L03

ISC all models Domed Wear Face, 1-Bolt Holding Style OEM # ISC-7114A SSF # 005-7114-27 ESCO HSP0074S07

This product requires custom shipping Allis Chalmers Svedala 30X42 Model RT75-105 Factory # 17-401-095-001 ESCO JAC3042M07

Minimum inlet pressure is for purpose of input adjustment CSA approved for unattended operation MEA approved for use in New York City Light enough for one-man operation Dual Fuel - Quick changeover from propane to natural gas Air flow switch and Hi limit switch ensures safe operation Thermostat to conserve fuel Optional wheel kit available Steel construction ensures durability

Allis Chalmers Svedala H-4000 Hydrocone Fits Sandvik H4800 and CH440 Crushers Old 44.400.031.001 ESCO GAC4000T04

Maximum operating pressure in psi: 5750 Maximum operating pressure in bar: 396 Vacuum rating required: 0 Minimum operating temperature Fahrenheit (f): -40 Maximum operating temperature Fahrenheit (f): 212 Minimum operating temperature Celsius (c): -40 Maximum operating temperature Celsius (c): 100 Minimum bend radius of hose (mm): 50.8 Minimum bend radius of hose (inches): 2 Inside diameter of hose (inches): .25 Inside diameter of hose (mm): 6.4 Hose construction: Two wire braid Hose base number: GH781 Dash size of hose: -4 (14 in) Hose tube material: Synthetic rubber Hose cover material: Synthetic rubber Outside diameter of hose (mm): 14.2 Outside diameter of hose (inch): .56 Hose part number: GH781-4 Hose Series: GH781 Dash Size: 04 Tube Material: Nitrile Reinforcement Material: Wire Braid Cover Material: TuffCoat Min Temperature (°F): -40 Min Temperature (°C): -40 Max Temperature (°F): 212 Max Temperature (°C): 100 Hose Type: 2S 100R2 MM+ Operating Pressure (psi): 5800 Operating Pressure (bar): 400 Burst Pressure (psi): 23000 Burst Pressure (bar): 1586

WLL8800#---- Kuplex® II Foundry hooks when properly used are designed for maximum service such as those applications encountered in foundry work. The throat of the hook is designed to accommodate standard trunnions. The tip of the hook is designed for ease of insertion into holes in the casting.Warning: Do not exceed Working Load Limits (WLL)!

Do not exceed Working Load Limits (WLL)! Failure to read, understand and follow the CAUTIONS listed here may cause serious physical injury and property damage. Do Not load an assembly in excess of working load limits shown. Do Not put an unequal load on one leg of a sling. Distribute the load evenly. Do Not expose assembly to impact, rapid lifts or sudden stops. Do Not tie knots or allow chains to become twisted. Do Not use a chain that appears to be defective, worn or damaged. Do Not fasten chain over sharp corners or edges. Protect with padding. Do Not tip load hooks. The latch must never support the load. When using non-cradle or non-shortening grab hooks in a shortening or choker application, the Working Load Limit (WLL) of the sling must be reduced by 20%.