Alwar, Rajasthan, India GST : 08BIPPS5263M2ZB Verified Supplier
We offer a complete product range of Apex Tile Adhesive, Versatile Tile Adhesive, Sun Waterproofing Adhesive, Virsun S-114 Crete Admix and Virsun S-57 Crete Admix
Features : Dual use - For both floors & walls Excellent non-sag formula Smooth, easy to use Improved impact resistance Increased flexibility Application : Can be used for interior applications on floors and walls over masonary, concrete, mortar beds and cement plaster.
Application : Thin bed mortar for laying blocks Smoothing over the block work As Adhesive to install tiles
SunWater proofing-1805 Waterproofing Membrane is a roller applied liquid rubber that forms a waterproof membrane for use under thin & thick bed installations of ceramic tile and stone, and other finishes. Application Recommended for residential and commercial floor and wall installations such as: Kitchen, bathrooms, gang showers and balconies. Also for use as a crack suppression membrane with reinforcing fabric. (over hairline nonstructural cracks up to 1/8 Degree (3mm)). For interior and exterior applications. Note: Membrane reinforcing fabric for coves, comers and board joints sold separately. Roll 6" (15cm)wide x 75' (22.85m) long. Advantages: Fast & Easy to install -applies like paint Proven history Suitable Substrates Concrete Cement Modal Beds Cement Backer Board Exterior Grade Plywood. Gypsum Wallboard. Concrete Mason Cement Terrazzo Brick Masonry Cement Piaster Interior use only
Packaging Details : Bucket
Virsun S-114 Crete Admix is a concentrated latex admix which Is diluted with water on site and then mixed with VIRSUN -229 to make thick bed adhesive, cement piasters, mortar beds, and screeds. Portend cement mortars which have been modified with Virsun -229 have greatly improved physical characteristics and can be used in exterior, interior, as well as underwater plasters, screeds, and renders. Virsun S-114 can also be used as a primer coat on various drywall boards like Gypsum wall boards, cement backer boards, Calcium Silicate boards, and wood panicle boards before installation of tiles/stones. Advantages: Greatly Improved compressive strength Improved adhesion More plastic mortars Can be used as the primer for various drywall boards before tile and stone installation. Can be used as a key coat mixing with cement and sand. Can be used for repairs& patching of concrete. Coverage : 12 mm 50 kg 1.25 litre 3.75 litre 25 sft 25 mm 50 kg 1 litre 4 litre 8 sft 50 mm 50 kg 0.83 litre 4.17 litre We 5 sft Shelf Life Factory sealed containers of this product are guaranteed to be of first quality for two (2) years if stored at temperatures >32 Degree F (0 Degree C)
Virsun S-57 Crete Admix is liquid latex admix mixed with Tile adhesive made with Virsun S-57 Crete Admix is more flexible and stronger than conventional Portland cement mortars. This strong bond Is especially important when vitreous and semi-vitreous tiles are installed and also for installation of natural stone and tile on the external wall. Application Vitrified files, ceramic tiles and natural stone in demanding areas. such as external facades, factories, and loading areas, should be set in Virsun S-57 Crete Admix mixed with VS Crete Filler Powder, because of the exceptionally strong bonding, shock and Impact resistance it gives to the adhesive. Advantages: Increased flexibility improved shock & impact resistance improved compressive strength Reduced water absorption Secure bond for vitrified tiles Suitable Substrates Concrete Brick Masonry Cement Plaster Concrete Masonry Cement Mortar Beds Ceramic Tile and Stone Gypsum Wallboard. Cement Terrazzo Coverage: Cement Backer Board "Interior applications only Packaging 20 liter Pat, Coverage Approx 200sft per 201fte using 1/4 Degree x 1/4" (6mrn x 6mm) square notched trowel for a bed of 3mm. Coverage will vary depending on trowel notch size, type and size of the and substrate Shelf Life. Factory sealed containers of this product are guaranteed to be of first quality for two (2) years If stored at temperatures 41 Degree F (5 Degree C).
Virsun S-1198 Crete Admix is specially designed latex additive for use with Virsun Crete Filler Powder to make high strength latex thin-set adhesive. The Adhesive made with Virsun 1198 Is suitable for Installing all types of ceramic tile, Vitrified tile, natural stone, and agglomerates. Also for use with Portland cement to make slurry bond coats for mortar beds to give the Improved performance and longer open time. To achieve longer open time under tropical or desert conditions, installation recommendations. Application Used for installation of all types of cc tile, VBrBed tile, brick. natural stone and agglomerates S-1198 Latex admix offers the speed and economy of Portland cement based adhesives with permanent, water-resistant dependability. Advantages: Superior shear bond strength - greater than ANSI A118.4 requirements. Suff able Substrates Concrete Cement Terrazzo Brick Masonry Cement Plaster Concrete Masonry Cement Backer Board" Cement Mortar Beds Ceramic Tile and Stone Gypsum Wallboard (Interior Only) 'Consult cement backer board manufacturer for specific installation recommendations and to verify acceptability for exterior use. Coverage : Coverage Approximately 200 sft per 20 liter using a 1/4' x 1/4 Degree (6mm x 6mm) notched trowel Coverage will vary depending on trowel notch size, type and size of the and substrate Shelf Life Factory sealed containers of this product are guaranteed to be of first quality for two (2)years If stored indoors and off the ground at temperatures >32 DegreeF (0 DegreeC).
Packaging Details : Bucket
Virsun S-901 Super Flexible Latex Admix is an extraordinarily flexible latex additive for use with thin set adhesives and other cement mixes. Virsun 901 Super Flexible admix Is specially formulated to provide a strong, super flexible bond to most surfaces, Including plywood. Recommended for Interior and exterior' use with VIRSUN Premium Thin-Set adhesive. 'Used in place of water with thin-set adhesive for Installing: ceramic tile, brick, natural stone, porcelain file on Plywood and variety of substrates. Advantages: Makes high strength shock resistant adhesive. Exceeds ANSI A118.4 shear bond strength requirements Strong, super flexible bond to many surfaces Safe and water cleanable, non-hazardous, Non-flammable liquid. Easy to use Sag-resistant Suitable Substrates Concrete Cement Mortar Beds Ceramic Tile and Stones Concrete Masonry Cement Backer Board' Cement Plaster Brick Masonry Exterior Grade Plywood" Asphalt Adhesives' Plastic Laminate' Cement Terrazzo Gypsum Wallboard" Vinyl or Other Resilient files" Inferior use only. 'Consult cement backer board manufacturer for specific Installation recommendations and to verify acceptability for exterior use. Coverage : Coverage Approx. 55-60 sft per 20-liter pail using 1/4" x 1/4" (6 x 6 mm) square notch trowel. Coverage will vary depending on trowel notch size, type, and site of the and substrate Shelf Ufe Factory sealed containers of this product are guaranteed to be of first quality tor two (2) years if stored at temperatures >32 DegreeF (CPC).
Features : Single component, ready to use Proven performance Application : Best suited for Exterior and Interior installation of ceramic/ vitrified/ Porcelain /Engineered stones and Natural Stones.
AAC BlocK ADHESIVE AAC BLOCK ADHESIVE MANUFATURE is a factory prepared blend of carefully selected raw materials, portland cement and graded aggregates and polymers. Designed for use with water to produce high strength thixotropic mortar, for laying aerated lightweight concrete, fly ash bricks, cement hollow blocks, cellular concrete blocks or smoothing over the block work surface in layers of up to 12mm thickness, that meet and exceed the requirements of National and International Approximately 200 sq.ft. per 50 kg bag when used at 2-3mm bed thickness Coverage is based on smoothness and evenness of the substrate, size of blocks used and the thickness of mortar used. Surface PreparationIf a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of adhesive for construction of block work.Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, existing paints, loose plaster etc.Mixing The product can be mixed by hand Pour water in a clean container and then add the powder SUN Block adhesive until the mixture becomes creamy and plastic. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for the immediate need.
Payment Terms : L/C, D/A, D/P, T/T, Western Union, MoneyGram,
Packaging Details : 40kg
Delivery Time : any
Features : Permanent tile fixing resistant to complete immersion Excellent quality Cost-effective Application : Can be used for interior applications on floors and walls over masonary, concrete, mortar beds and cement plaster.
We are based in Alwar(India) and ensure to make available the entire range of products to any required destination. Our company stocks the product in mass. Thus, we can cater to bulk/retail requirements with easy and ensure fast delivery of product.