• boiler pressures10.55 kg/cm² (150psig).

Raw water contains impurities in the form of dissolved gases, dissolved Solids and suspended solids. Chemical water treatment may modify the form of the impurities but will not completely remove them and will normally increase the dissolved solids level. As steam is evaporated the concentration of total dissolved solids (TDS) increase in the boiler water. If the TDS concentration is allowed to get too high then carryover of boiler water with stem will occur. This carryover can cause serious damage to the steam and condensate systems through corrosion and deposition on heat transfer surfaces. The consequent product contamination cannot be tolerated in application where steam is used in food, drink and medical sterilization processes.

• Size96mm X 96mm X 150mm

PH indicators advanced micro controller based design. Available in panel type, field type, Flame proof and weather proof version. Easy front key calibration . Multi parameter display by a key press. LED indication for relay status. Error code for self diagnosis. Two Programmable isolated relay outputs . Pass code provision for Authorised settings .

• Power Supply220-240 VAC, 50-60 Hz and 5VA
• SizePanel Type 96mm X 96mm X 150mm, Field Type 200mm X 120mm X 75mm
• Weight2 Kg.

Advanced micro controller based design Available in panel type, field type, Flame proof and weather proof version. Easy front key calibration Multi parameter display by a key press LED indication for relay status Error code for self diagnosis Two Programmable isolated relay outputs Pass code provision for Authorised settings 3 ½ digit, 14mm high intensity red LED display.

• Size200 X 120 X 80 mm
• Accuracy+ 0.5 %

Compact design signal converter housing Mounted on flow meter Automatic zero point correction using D.C. pulsed technique. Measurement is independent of fluid properties, density, viscosity, temperatures and solid content. Smooth inner tube no pressure losses. Various options available. Easy to install and connect up. Low power Consumption. PCB’s replaceable at site without need for recalibration. Extra thick liner ensures long life.

• boiler pressures10.55 kg/cm² (150psig).

Raw water contains impurities in the form of dissolved gases, dissolved Solids and suspended solids. Chemical water treatment may modify the form of the impurities but will not completely remove them and will normally increase the dissolved solids level. As steam is evaporated the concentration of total dissolved solids (TDS) increase in the boiler water. If the TDS concentration is allowed to get too high then carryover of boiler water with stem will occur. This carryover can cause serious damage to the steam and condensate systems through corrosion and deposition on heat transfer surfaces. The consequent product contamination cannot be tolerated in application where steam is used in food, drink and medical sterilization processes.

• Size96mm X 96mm X 150mm

PH indicators advanced micro controller based design. Available in panel type, field type, Flame proof and weather proof version. Easy front key calibration . Multi parameter display by a key press. LED indication for relay status. Error code for self diagnosis. Two Programmable isolated relay outputs . Pass code provision for Authorised settings .

• Power Supply220-240 VAC, 50-60 Hz and 5VA
• SizePanel Type 96mm X 96mm X 150mm, Field Type 200mm X 120mm X 75mm
• Weight2 Kg.

Advanced micro controller based design Available in panel type, field type, Flame proof and weather proof version. Easy front key calibration Multi parameter display by a key press LED indication for relay status Error code for self diagnosis Two Programmable isolated relay outputs Pass code provision for Authorised settings 3 ½ digit, 14mm high intensity red LED display.

• Size200 X 120 X 80 mm
• Accuracy+ 0.5 %

Compact design signal converter housing Mounted on flow meter Automatic zero point correction using D.C. pulsed technique. Measurement is independent of fluid properties, density, viscosity, temperatures and solid content. Smooth inner tube no pressure losses. Various options available. Easy to install and connect up. Low power Consumption. PCB’s replaceable at site without need for recalibration. Extra thick liner ensures long life.