WELD MASTER INDIA

Peenya, Bangalore, Karnataka

• Special FeaturesPhase Fail Protection
• Welding TimeOnly 20 Milliseconds
• SuitabilityStuds (3mm ~ 10mm) Sheets (1.25 ~ 2.5mm)
• OperationSemi-skilled Operation
• PerformanceHigh Performance
• Welding FeaturesShorter Weld Cycles
• Base Metal Thickness4mm And Above

• FeaturesHigh Efficiency,Low Maintenance
• UseCooling Resistance Machines
• MaterialMetal Casing
• Storage TypeIndoor Installation
• Number Of FlowerCooling Equipment

• FeaturesQuick Recharge, Energy Savinge
• Base Material Thickness.8-2.5mm
• Stud Diameter3-10 Mm
• Suitable MaterialsMild Steel, Stainless Steel

• ApplicationDeck Sheeting,Railway,Steel Buildings,Bridges,Columns
• Number Of FlowerShear Connector Stud
• AppearanceModern, Sturdy, And Attractive
• DimensionsDia 3mm To 25 Dia

Headed shear connector stud can be used for welding flat surfaces, from Inside/outside angle through the deck. Headed Shear Connector Studs are designed to interconnect the Concrete slabs to the load bearing steel beams to hold the load capacity of concrete and the steel beam in steel buildings, bridges, Columns and etc. Advantages Modern, sturdy, and attractive appearance PEB BUILDINGS, Deck sheeting & Railway Dimensions of shear connectors Dia 3mm to 25 dia

• Brand NameWELD MASTER INDIA
• UsageWelding Battery Lithium Ion Packs,Power Banks etc.
• Rated Input Power220V
• Minimum Order Quantity1 Piece
• Number Of FlowerBattery Spot Welder

Lithium Iron Battery Tap Welder Machine can be hand type or table mounted type. Extensively used in welding of lithium-ion battery power banks. battery spot welders are used in welding of battery packs, power banks, lithium ion batteries, battery cells, nickel welding, hand type spot welder, table spot welder etc.

• ApplicationSuitable For 65%,Low Contact Resistance
• Input PhaseThree Phase
• TechnologyMedium Frequency Inverter
• BenefitsSmaller Transformers
• Frequency1000Hz

Three Phase Inverter DC utilizes three-phase balanced input. Current is in full wave form rectified to DC and switch to 1000Hz or higher to produce AC supply to primary transformer. The current is rectified into DC for welding afterwards. Medium (till 1000Hz) Frequency Inverter Welders use millisecond pulse width modulation (switching) technology with closed-loop feedback to control the weld energy in sub-millisecond increments. Three phase input current is full wave rectified to DC and switched at 1kHz to produce an AC current at the primary of the welding transformer. The secondary current is then rectified to produce DC welding current with an imposed, low-level, AC ripple. The high-speed feedback circuitry enables the inverter power supply to adapt to changes in the secondary loop resistance and the dynamics of the welding process. For example, a 1 kHz inverter power supply adjusts the output current every 0.5 miliseconds after rectification, which also allows the weld time (duration of current) to be controlled accurately in increments as small as 1 milliseconds. The high frequency closed loop feedback can be used to control (maintain constant) either current, voltage, or power while also monitoring another of the same three parameters. Additional benefits of high frequency switching technology include reduced power consumption, smaller welding transformers, and the use of a very short pre-weld “check pulse” to test electrode and parts positioning prior to executing a weld. The result of this pre-weld check can be used to inhibit the weld by setting check limits. CONSTANT CURRENT can be used for 65% of all welding applications including those that exhibit low contact resistance, small variability in contact resistance, flat parts, and multiple part “sandwiches.”

• Materials WeldableStainless Steel, Alloy Steel
• KVA OptionsWMI 10,WMI 15,WMI 20
• AppearanceModern, Sturdy
• Power Supply Options220 And 415 2 Phs
• Design FeaturesModern, Sturdy, Attractive etc.
• OperationPedal Operated

• Electrical DesignHigh-efficiency Core
• AppearanceModern, Sturdy
• FrameHeavy Steel Body
• Power Supply220 or 440 V,50Hz
• Material CapabilitiesStainless Steel, Alloy Steel
• Controller Features5 Membrane Keys, 2 Selector Switches

• FeaturesVarying Charging Voltage Options etc.
• AdvantagesSuitable For Welding Heat Sensitive Parts
• Number Of FlowerResistance Welding Machine