The FRP Square Cooling Tower, which we offer, is manufactured as per the set industrial standards. Also, we undertake repairing and revamping services of any type of FRP Square Cooling Tower. We offer these FRP Square Cooling Towers at competitive rates to the clients. Highlights

• Operates on the induced draft counter flow principle operation
• The fan creates air movement vertically pulled upwards on tower across the fills in opposition to the water flow
• Hot circulating water enters the water inlet headers and sprays through non clogging PP spray nozzle
• Even Water distribution
• Well-designed PVC Drift Eliminators are fitted
• Reduces Drift Losses
• Has an Inspection Door
• Allows easy access for inspection and maintenance
• Square tower can be installed in multi cell also

• Compact design, corrosion resistant and lightweight
• Durable service Life
• Maintenance free
• Higher efficiency
• Minimum drift loss of water
• No contamination, due to dust or foreign particles
• Piping cost negligible and suitable for small unit

• FRP Casing : Cooling Tower Casing is made of selected grade materials of tough Fiber Glass Reinforced Polyster and resins etc. An additional embossing is provided for extra strength of large Cooling Towers.
• Header Pipes : The header pipe designed for proper distribution of water over the FILLS so that proper contact time for air to water is achieved. The header pipe is manufactured in G.I., P.P. with FRP moulded construction which makes it Non Corrosive Type & Long Lasting.
• Water Distribution Nozzle : We are offering low pressure drop, non-clogging, ABS make solid cone type nozzle for distributing the water on the fill pack area. Each nozzle is designed to operate on a water fluctuating load as good as 20%. Each nozzle can cater the service area of 1.2m x 1.2m at an inlet pressure of 0.3 kg. Per cm.sq.
• Drift Eliminator : CCS Drift eliminators, to reduce carry over losses through of moistures drop in the air stream. The individual drift eliminators of s-shaped corrugated sheets are bonded with subsequent layer to creat the structure.
• PVC Honeycomb Fills : PVC Honeycomb type fills having extended contact area. Splits incoming air and water into several streams spread evenly across the water cross section increasing heat transfer rate easy to replace.

The FRP Square Cooling Tower, which we offer, is manufactured as per the set industrial standards. Also, we undertake repairing and revamping services of any type of FRP Square Cooling Tower. We offer these FRP Square Cooling Towers at competitive rates to the clients. Highlights

• Operates on the induced draft counter flow principle operation
• The fan creates air movement vertically pulled upwards on tower across the fills in opposition to the water flow
• Hot circulating water enters the water inlet headers and sprays through non clogging PP spray nozzle
• Even Water distribution
• Well-designed PVC Drift Eliminators are fitted
• Reduces Drift Losses
• Has an Inspection Door
• Allows easy access for inspection and maintenance
• Square tower can be installed in multi cell also

• Compact design, corrosion resistant and lightweight
• Durable service Life
• Maintenance free
• Higher efficiency
• Minimum drift loss of water
• No contamination, due to dust or foreign particles
• Piping cost negligible and suitable for small unit

• FRP Casing : Cooling Tower Casing is made of selected grade materials of tough Fiber Glass Reinforced Polyster and resins etc. An additional embossing is provided for extra strength of large Cooling Towers.
• Header Pipes : The header pipe designed for proper distribution of water over the FILLS so that proper contact time for air to water is achieved. The header pipe is manufactured in G.I., P.P. with FRP moulded construction which makes it Non Corrosive Type & Long Lasting.
• Water Distribution Nozzle : We are offering low pressure drop, non-clogging, ABS make solid cone type nozzle for distributing the water on the fill pack area. Each nozzle is designed to operate on a water fluctuating load as good as 20%. Each nozzle can cater the service area of 1.2m x 1.2m at an inlet pressure of 0.3 kg. Per cm.sq.
• Drift Eliminator : CCS Drift eliminators, to reduce carry over losses through of moistures drop in the air stream. The individual drift eliminators of s-shaped corrugated sheets are bonded with subsequent layer to creat the structure.
• PVC Honeycomb Fills : PVC Honeycomb type fills having extended contact area. Splits incoming air and water into several streams spread evenly across the water cross section increasing heat transfer rate easy to replace.