We are offering link belts. the full depth of a v-section t-link belt is made up from 3 overlapping sections. the belt is joined or broken by simply rotating the t-headed pins until they line up with the slots cut in a each link. although the pins go right through each link there is always clearance for them in the bottom of the v pulley commonly known as "link belts", which is a type of v-belt (it cannot be used on flat-belt drives), is widely used in industrial and marine applications. Although more expensive than ordinary v-belts it does have some important advantages.

We are offering industrial belts most widely used on high speed and high torque drives on light, heavy industrial and automotive machines. These belts have exceptional length stability and drive uniformity, "match free" provides assured belt length and easy inventory control. Heat & oil resistant plus static conductive.

We are offering flat belts (canvas & conveyor). polydrive range of flat belts and conveyor belts covers a wide spectrum of types and applications. The following programme is a pointer towards the reach and production capabilities of polydrive.

We are offering wedge belts & fhp/ m fraction. wedge belts have been the result of continuous thrust by the manufacturers and the users on higher power transmissions with reduction in space requirements. Wedge belts can transmit high power to extent of 1.5 to 2 times the classical belts with same top width this has been achieved by the dimensional changes, part from better cord constructions used and the optimum placing of the cord line which provides the best support to the cord while in motion. For efficient performance of wedge drives it is essential that the proper tension be maintained in the drives, failure to maintain the same will render the purpose of wedge belts ineffctive.

We are offering rubber conveyor belts. rubber conveyor belts consist with a continuous loop of two or more pulleys or rollers to rotate them. The rubber conveyor belts are used to convey items with irregular base or bags of product that would droop between rollers. The conveyor belt consists of two or more layer which is made up of rubber.â

We are offering cogged belts. Suitable for all industrial applications, particularly where small or sub-minimal sheave diameters are required. features : 1. Tooth notches constructed onto the belt during manufacturing, make this belt well suited for drives with smaller diameter sheaves. 2. Belt edge is machined for even sheave groove contact resulting in less slip and wear. 3. Flexible cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration.

We are offering cogged belts. Suitable for all industrial applications, particularly where small or sub-minimal sheave diameters are required. features : 1. Tooth notches constructed onto the belt during manufacturing, make this belt well suited for drives with smaller diameter sheaves. 2. Belt edge is machined for even sheave groove contact resulting in less slip and wear. 3. Flexible cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration.

We are offering tyre couplings. polydrive tyre couplings provide all the desirable features of an ideal flexible coupling, including taper lock fixing. The polydrive tyre coupling is a "torsionally elastic" coupling offering versatility to designers and engineers with a choice of flange combinations to suit most applications. the flanges are available in either f or h version taper lock fitting or bored to size b.

We are offering hexagonal (double) v-belt. Both bottom and top faces can be used for lower transmission. Best suited to multi pulley drive, being highly flexible. Heat & oil resistant plus static conductive. features : suitable for drives where belts bend both ways on several pulleys. specially compounded base gives good flex fatigue resistance. designed for low heat build-up to extend belt life.

We are offering industrial belts most widely used on high speed and high torque drives on light, heavy industrial and automotive machines. These belts have exceptional length stability and drive uniformity, "match free" provides assured belt length and easy inventory control. Heat & oil resistant plus static conductive.

We are offering link belts. the full depth of a v-section t-link belt is made up from 3 overlapping sections. the belt is joined or broken by simply rotating the t-headed pins until they line up with the slots cut in a each link. although the pins go right through each link there is always clearance for them in the bottom of the v pulley commonly known as "link belts", which is a type of v-belt (it cannot be used on flat-belt drives), is widely used in industrial and marine applications. Although more expensive than ordinary v-belts it does have some important advantages.

We are offering banded belts. Banded belts are made up from classical, wedge or narrow belts with strong tie band over them. Each band may contain the required number of belts. Maximum up to 5 belts in one tie, depending upon the drive conditions, are recommended.