Clamps #869877

'TOOLFAST' Universal Strap Clamp is most suitable for die clamping on power presses and a very useful clamp for job clamping on 'T' slot table of Drilling, Milling, Shaping, Boring and other machine tools. No supports are required at the rear of the clamp since the body of the clamp is self-positioning as the rear part rests on the table and front holds the job. The body positions itself with the help of swival hinge pin according to the thickness of the woi'Kpiece, the T-Bolt remaining in vertical position and the nut is tightened on the flattened portion of swival hinge pin. Clamp is supplied complete with hardened T-Bolt & special nut.

'TOOLFAST' Push Action Toggle Clamps with Pneumatic Operation are available in following sizes.

Low height design of these hold down toggle clamps requires less overhead clearance as the handle remains in horizontal position while clamping. BR Arm models are also available.

TOOLFAST' Mould Clamp is designed specially for low height applications only such as clamping of moulds on plastic injection moulding machines & pressure die casting machines. The compact front portion of the clamp enables it to penetrate into the limited clamping area of the mould and clamp it. The positioning of forged swival washer on required curved groove enables the operator to set the center distance between the clamping portion and the clamping bolt as per the nearest tapped hole available on platen (where there are noT-slots). No supports are required at the rear of the clamp as the rear portion rests on the platen and front holds the mould. Flanged nut is tightened on the swival washer which takes care of the positioning of clamp body. These clamps are equally useful on pressure die casting machines, hydraulic presses & power presses where low height clamping is done.
Clamps are supplied complete with swival washer, flanged nut & clamping stud or T-Bolt as shown in tables below.

'TOOLFAST' Mini Pinch Clamp is useful for clamping of thin plates form side faces. Body made of hardened alloy steel is in the form of a T-Nut which slides easily into the T-slot. When rear screw is tightened, the clamp is held tightly with the T-slot and then by tightening the front bolt, it gives a downward as well as forward clamping force to the job. Only a required small portion of the clamp comes above the surface of T-Siot table, rest of the body of clamp remains under the top surface of the T-Siot table. Hence, it can clamp thinnest plates positively and still remain under the top level of the job. This clamp is most suitable for top facing of thin plates on milling, shaping and planning machines. Supplied complete with standard front & rear screws.

These Strap Clamps have teeth at rear matching to that of Step Blocks for the Step Blocks to be used as supports. Unlike other clamps, single piece of Step Block not a pair can be used as support with Stepped Strap Clamp.

Finger clamp is specially designed for holding at curved surfaces or inside holes. Most useful for clamping of heavy blocks while machining where there are no steps for clamping and top surface has to be left clear for machining. In such cases holes are drilled on the side faces and finger clamps can be used for clamping on that holes.

This model is for applications where heavy duty Latch type clamping is required. Clamp base and Latch plate are fabricated out of Solid Steel. Pulling pin is housed in carbon steel bush for extra rigidity. Also available TR model with an added advantage of trigger lock which enables the clamp to remain locked even in conditions of high vibration unless the trigger is pulled.

TOOLFAST compact milling clamp is the most multipurpose, quick and easy to use down-hold milling clamp. It is equally suitable for clamping while all kinds of machining operation on Drilling, Milling, Machining Centre, EDM etc. This clamp does not require any support blocks or any kind of adjustment, clamping is done by simple turning of the removable spanner key.

Standard Accessories provided with Clamp:
Standard Hex. Head Clamping Spindle assembly is provided as standard accessory.

Optional Accessories:

User can select an optional clamping spindle assembly as per the application from the different types of clamping spindle assemblies shown on one of the following pages and order these separately.

These are newly introduced models having same dimensions of mounting etc. as PAC-HV series given on previous page but with a modified low height handle suitable for only horizontal locking.

These are economy models of strap clamps. Can be used where simple shape of a plain strap can serve the purpose.

'TOOLFAST' manufactures all models of wedge clamps with new patented design now in India.

These have extra material on jaws(soft) to machine as per the workpiece shape enabling fixturing of uneven or unusual shape workpieces.

TOOLFAST offers a standard 60mm jaw width vice which is capable of clamping multiple workpieces. All parts such as TWC wedge clamp, fixed jaws and the main body are modular and interchangeable.

*Model VTWC-16-60-350 available as standard having overall length 350mm capable of jaw opening 91mm in case of two workpieces.

*This vice can also be supplied in custom built lengths to suit different sizes of workpieces. Send your enquiries to us if you feel that 60mm jaw width vice is suitable for your workpiece. Additional fixed jaws and TWC series clamps can be included in the vice if more than two workpieces to be clamped.

*For uneven or unusual shape workpieces, TWC-M and TWC-P series wedge clamps can also be used in above vice.

Pull Action Clamps are Latch type clamps used for sealing chambers, lids, doors of moulds, drums, containers or other vessels etc. Also suitable for clamping moulds in industries such as resin, fibre glass, chemical & food.

'TOOLFAST' Pull Action Clamp has a unique design which enables use of the same clamp as a horizontal pull action clamp as shown in figure (A) as well as a vertical pull action clamp as shown in figure (B) below by using two different holes H1 and H2 for pulling pin P to be located in. Clamp is supplied complete with U-bolt & Latch Plate.

Low height design of these hold down toggle clamps requires less overhead clearance as the handle remains in horizontal position while clamping.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly complete with U-Fianged washers and lock nuts is provided as standard accessory with above clamps. BR-arm models are provided with bolt retainers along with clamping spindle assembly.

'TOOLFAST' Tapped End Clamps are Straps having special threaded adjustable support at the rear which can be adjusted to required height. Most useful clamp for plastic injection moulding or pressure die casting machines where mould I die is clamped in vertical position and these clamps with screwed in adjustable support are convenient to the operator as other loose supports tend to fall down while setting. Hardened adjustable support with large diameter forged base gives rigid clamping support and ensures machine bed safety. Extra thick body of the clamp accommodates more number of threads for rigidity of screwed support.

The Popular 'TOOLFAST' mould clamp is now available in forged steel body for exira strength. All models shown below are similar to the MC models on the previous page.

'TOOLFAST' Low Height Pinch Clamp is useful for job clamping where complete top surface of the job is to be machined in one setting and hence can be clamped only from side faces. When serrated front portion is pressed against the job by tightening the front bolt, it gives a downward as well as forward damping force. Body is made of hardened alloy steel. It is most useful on Milling, Shaping, Planning and Jig boring machines. Supplied complete with hardened T-Nuts & Standard Bolts.

These are straight base version of WTC series. All other features are same. Arm and handle are supplied loose alongwith the clamp which will be welded at desired position before use.

These toggle clamps have a Solid Arm with a tapped hole at the end. This arm can also be cut to any length and hole can be made at any desired position or a separate clamping assembly can be welded at any desired point as per the application.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly is provided as standard accessory with all above clamps.
Optional Accessories :User can select an optional clamping spindle assembly as per the application from the different types of clamping spindle assemblies shown on one of the following pages and order these separately.

These toggle clamps are similar to VHDT models but with Base Straight. Straight Base design enables mounting on a vertical surface.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly complete with U-Flanged washers and lock nuts is provided as standard accessory with above clamps.

Smaller sizes of VHDT models are also available in T-Handles.These are available in U-arm models only as shown in table below.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly complete with U-Flanged washers and lock nuts is provided as standard accessory with above clamps.

This model has vertical handle with a right angled dual mounting base which can be base flange mounted as well as front mounted on side wall of a fixture.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly complete with U-Flanged washers and lock nuts is provided as standard accessory with above clamps.

'TOOLFAST' Push/Pull Action Toggle Clamps have a straight line action as the plunger moves in straight line forward & backward with easy to operate handle. The plunger moves forward and locks as the handle is moved forward and plunger also locks in retracted position when handle is moved backward. Hence these clamps can be used as push as well as pull action clamps. Hardened & ground plunger moves in precision machined bore.

This model with front base is most popular because of its rigidity due to mounting base just under the load bearing surface of plunger movement.

'TOOLFAST' Push/Pull Action Toggle Clamp - Centre Base has its base at the centre and the bigger two sizes have more centre height than the front base model to accommodate larger work pieces. Width of the mounting base is also less in this case which makes this type of push action clamp more compact. Other features of this clamp are same as in case of front base model.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly is provided as standard accessory.

Optional Accessories :User can select an optional clamping spindle assembly as per the application from the different types of clamping spindle assemblies shown on one of the following pages and order these separately.

These are modular weldable clamps which allow the designer complete flexibility to position the base, clamp arm and handle and weld them in any desired position to suit the application. The base, arm and the pipe handle are supplied alongwith the clamp separately, to be welded by the user before use. The main body is made of accurately machined components having hardened and ground pivot pins and bushes.

These toggle clamps have a flanged base with holes for mounting on the fixture plate. Handle remains in vertical position while clamping. Available in two types of clamping arms as shown below:

U - Arm :-This is the most widely used type which permits to locate the clamping spindle anywhere along the length of the arm.
BR - Arm :-This type of Arm has s Strip Arm onto which the bolt retainer can be welded by the user at any desire angle. Bolt retainer is supplied loose with this model.

Standard Accessories provided with Clamp :Standard Hex. Head Clamping Spindle assembly is provided as standard accessory with all above clamps. U-Arm models are provided with 2 nos. U-Flanged Washers also along with clamping spindle assembly and BR-arm models are provided with bolt retainers along with clamping spindle assembly.

Optional Accessories :User can select an optional clamping spindle assembly as per the application from the different types of clamping spindle assemblies shown on one of the following pages and order these separately.

This is a new version of low height pinch clamp (PC Series) having step to support the workpiece above the machine table for through milling and drilling. Each PCS series clamp comes with a suitable size step (ST-PCS Series) as standard.