Other Products / Services #4605087

Ethernet Interface (WIZNET 7010B+ or equivalent).16x2 alphanumeric display (LCD) with back lightOn board switches and LEDs.Circuit to test on-chip Compare, Capture, PWM and Analog Comparator.RS232C Serial interface through on chip UART0 and UART1.On-chip 10-bit ADC0 and ADC1 is used for 4-20mA current loop interface.On-chip 10-bit ADC2 is used for voltage interface.On-chip 10-bit ADC3 is used for ambient temperature measurement circuit using LM335.Onboard interface to SPI compatible 12-bit DAC device and SD card.Onboard interface to I2C compatible NVROM (Non Volatile Read Only Memory) and RTC (PCF8523).A 10 pin FRC box connector for interfacing external GPS module using UART0UART1.A 9-pin Female D-sub connector for interfacing external GSM module using UART1.A 9-pin Male D-sub connector for interfacing RS485 interface using UART1.USB to serial interface using UART0 and onboard USB interface IC.CPLD is used for counter operation and generation of chip selects for onboard interfaces.Provision for JTAG and ISP for debugging and programming the controller.Elegant enclosure with Test Points for monitoring.Software examples compiled using ICC-AVR compiler.Provision to interface ALS standard external interfaces through 26 pin FRCPower supply required +5V DC, 1.5A.

Tutor based on LPC2148 ARM 7 ControllerSpeed:12Mhz default, up to 60Mhz with on chip PLLProtocol supportedRS232RS485I2CSPIZigbee(1no)GPS Module(1no)Flash -512KB, SRAM-32KB320X240 Monochrome Graphics LCD included on boardUART for programmingUART for full UARTUART for RS485UART for RS422SD card interfaceOnboard temperature sensor interface using LM358 LEDs to display I2C4X4 Matrix keyboardStepper motor interface with on board motorI2C compatibleEEPROM(64KB)RTC with suitable batterySPI compatible EEPROM(32KB)Microcontroller LPC2148 provided as daughter board for easy maintenanceBuzzerDifferent test points for each protocolSoftware Features:Tutorial for RS232Tutorial for RS422Tutorial for RS485Tutorial for SPITutorial for I2CTutorial for ZigbeeeTutorial for GPSSample application for protocol:RS232(Serial communication)RS422(Full duplex), RS485 (Half duplex) SPI (EEPROM) I2C(EEPROM)Code compilation using SCARM

XILINK USB DONGLELOGIC ANALYSER AND PATTERN GENERATOR UNIVERSAL PROGRAMMER Why Programmer The Programmer is an important tool in developmental activities. The tool helps you to program various devices as per your requirement.There are various models depending upon the requirement of the developer.Various adaptors are also available for various kinds of packages.

MAIN UNIT: Microprocessor based PLC System with built in 8 Digital input line, with RS232 Serial Interface of Industrial grade PLC will be used. The system comes with Ladder programming and communication software compatible with IBM PC. All the inputs and outputs are brought out to the panels for the ease of studying various Static application panels and also Sample Ladder programs are supplied for better understanding of PLC. The Panel is built with necessary Power supply required for the PLC and the Simulation Panels. The system can be used for any control applications, which come across in Industrial Environment by writing Logic program as per requirement.

VARIABLE POWER SUPPLY : 0 30V ; 1A ; SINGLE VARIABLE POWER SUPPLY : 0 30V ; 2A; SINGLE VARIABLE POWER SUPPLY : 0 30V ; 1A ; DUAL VARIABLE POWER SUPPLY : 0 30V ; 2A; DUAL VARIABLE POWER SUPPLY : 0 300V ; 1A 2A; MULTI OUTPUT POWER SUPPLY : 0-30V, 1A 2A +5V, 1A 2A +- 15V, 1A 2A

ACCURACY +-0.5% + 1 DIGITRANGE L 0-2000HC 0-2000UFDR 0-20 M RESOLUTION0.1HPFDISPLAY 3 DIGIT 0.5 LEDMEASUREMENT FREQUENCY 1KHz UP TO 2FH, 100Hz FOR ABOVE 2FHDISSIPATIONFACTOR 3 DIGIT DISPLAY PROVIDEDMEASUREMENT REMOTE KELVIN SENSINGPOWER AC MAINS 230 V 10%, 50HzSIZE All Address, Data and Control signals are terminated in 50 pin berg stick for user expansionWEIGHT LESS THAN 3 KG

This unit is Microcontroller based controller circuit to accurately generate pulses to energize the stepper motor winding in the desired sequence. Power Transistor based driver circuit to drive the stepper motor. 5 Seven segment display to set and display the parameters. From this controller we can set the speed of the stepper motor in RPM, set the number of steps the motor can move. We can set the direction of rotation forward and reverse direction. We can also set half step and full step mode.

SPRING BOARD WITH 16 PIN IC BASE - DUAL LINESPRING BOARD WITH 16 PIN IC BASE - SINGLE LINESPRING BOARD WITH 8 PIN IC BASE - DUAL LINESPRING BOARD WITH 8 PIN IC BASE - SINGLE LINEGENERAL PURPOSE SPRING BOARD WITH 32 SPRINGSSPRING BOARD WITH TWO 16 PIN ZIF SOCKETS AND 64 SPRINGSCUSTOMISED SPRING BOARDS CAN ALSO BE DONE

MICROCONTROLLER BASEDVARIABLE DC OFFSET CONTROLVARIABLE AMPLITUDE CONTROLBUILT-IN 5 DIGIT INT AND EXT COUNTER DISPLAY2-IN-1 FUNCTION FREQUENCY COUNTER AND GENERATOR50 OHMS AND 600 OHMS OUTPUT IMPEDENCE SELECTABLEVARIABLE OUTPUT LEVEL CONTROL WITH 10db, 20db and 40db ATTENUATOR RANGESVERSATILE WAVEFORMS OF SINE, SQUARE, TRIANGULAR AND PULSE WITH VARIABLE DUTY CYCLE

NXP Semiconductors LPC 2129 1632 bit ARM7TDMI-S : 1632 bit LPC2129 with 256K Bytes program Flash, 16K bytes RAM, RTC, 2x32bit timers, 7xCCR, 2xCAN, 4x10-bit ADC, 2xSPI, I2C, 6xPWM, WDT, 5V tolerant IO, up to 60MHz operation, using 12MHz crystal.Two on board voltage regulators 1.8V and 3.3V, Input to this will be from External +5V DC Power supply through a 9-pin DSUB connector. One power LED to indicate the presence of 5V.Two RS232 interface circuits with 9 pin DSUB connectors : UARTO is used by the Boot loader program, to program LPC2129 Flash memory without external programmer. UART1 is general purpose RS232 and may be used by user program.I2C bus interface circuit to DS1307 (RTC), 24C16 (NVROM), PCF8591 (ADC & DAC)SPI bus interface to MCP3202 (12-bit ADC & Temperature Sensor LM335)CAN bus TRANSCEIVERS - two numbers of PCA82C250 with to 9-pin DSUB connectors.One LED connected to the PWM output.Interface circuit for Compare & Capture feature testing, circuit for external DC-Motor, on-board Relay Buzzer.4 High-Current (300 mA) output lines terminated in a Power Mate ConnectorLCD 16x2 display : two numbers 7-Segment displays.8 no. of general purpose LEDs connected to output latch4x4 key-matrix connected to the port lines of the controller.Reset push-button for resetting the controller.Two standard 26-pin FRC connectors to connect on-board interfaces or to connect to some of ALS standard external interfaces.The useful port line (extension ports) of controller are terminated in berg pinsStandard JTAG connector with 2x10 pin layout.RTOS examples.

Frequency Range: 0Hz to 5MHz.Based on reliable DDS Technology digital waveform generation that can give accurate Frequency Amplitude characteristicsNo need for Calibration as the intelligence inside the unit auto calibrates on every power onSweep and Arbitrary wave form generation mode using PC software for frequencyProgrammed FSK, FM modulation using PC software.Inbuilt Frequency counter.Electronic Attenuators for -20, -40 and -60dBPhase control to vary from 0 360 degrees in steps of 1 degree (On Selected Models)Output voltage 20vp-pEasy to operate Digital switch based rugged Manual front panel operationLCD based menu selectionRemote PC controlled operation using PC software.

exas Instruments TMS320C6713 DSP operating at 225 Mhz.Embedded USBJTAG controller with plug and play drivers, USB cable includedTLV320AIC codec2M x 32 on board SDRAM512K bytes of on board Flash ROM3 Expansion connectors (Memory Interface, Peripheral Interface and Host Port Interface)On board IEEE 1149.1 JTAG connection for optional emulator debugFour 3.5 mm audio jacks (microphone, line-in, speaker and line out)4 user definable LEDs4 position dip switch, user definable+5 Volt operation only, power supply includedSi ze : 8. 25" x 4. 5" ( 210 x 115 mm) , 0. 062" t hi ck, 6 layersCompatible with Spectrum Digitals DSK Wire Wrap Prototype Card SOFTWARE FEATURES: TMS320C6713 DSK specific Code Composer Studio from Tex as InstrumentsTest sample code provided to reduce coding time

Optical communication has many advantages over the traditional electrical counterparts. It is insensitive to electromagnetic interference, it offers ground and voltage isolation between the transmitter and the receiver, it provides security from tapping and there will be no sparking at the connecting ends. This trainer uses LEDs in visible range (660 nM) as transmitter, fast PIN-Photodiodes as receiver. A Plastic Optic Fiber (POF) is used as the channel connecting light signal from the transmitter to the receiver. Each of the transmitter and receiver are placed in a PCB mountable plastic housing. A 2.2 mm aperture is provided to hold standard 1000 micron POF. No fiber stripping is required. Microlens is a part of the housing.

LPC1768 is ARM Cortex M3 based micro controller with 512KB flash memory and 64KB SRAM12MHz Crystal allows easy communication setupOne on board voltage regulator for generating 3.3V. Input to this will be from External +5V DC Power supply through a 9-pin DSUB connectorOne RS232 interface circuits with 9 pin DSUB connector: this is used by the Boot loader program, to program LPC1768 Flash memory without external ProgrammerPiggy Back module containing LPC1768 controllerStandard JTAG connector with ARM 210 pin layout for programmingdebugging with ARM-JTAGStandard 26-pin FRC connectors to connect to on-board interface or some of ALS standard External InterfacesReset push-button for resetting the controllerSPI Interface: 2 channel ADC IC with POT and Temperature sensorI2C Interface: NVROM ICOn chip ADC interface circuitTwo External interrupt circuits with LED indicationLCD 162 alphanumeric displayOn-board eight push-button switches4x4 Key-Matrix connected to the port lines of the controllerEight general purpose LEDsFour-digit multiplexed 7-segment display interface8-bit DAC interface

This interface allows the user to study the interface of a single stepper motor, through port lines and is compatible with our Microprocessor Microcontroller Trainer kits NIFC-05A - LOGIC CONTROLLER INTERFACE This interface provides buffered 12 TTL Outputs and 12 TTL Inputs. Logic state is indicated by LEDs The 12 inputs are connected to DIP switches and 12 outputs are connected to LEDs and also terminated in pads. The status of inputs are also indicated through LEDs and the inputs are also terminated in pads A number of experiments like combination controller (AND, OR, XOR and NOT operations), sequential controller, programmable counter, multiplexer etc. can be conducted using this interfaceThe interface operates off 5V DC and is housed in our standard plastic box

LPC1768 32 Bit ARM Cortex-M3 based processor with 512K bytes Program Flash, 64K bytes RAM12MHz Crystal allows easy communication setupOne on board voltage regulator for generating 3.3V. Input to this will be from External +5V DC Power supply through a 9-pin DSUB connectorReset push-button for resetting the controllerThree of the four controller UART's are made available to user for external interfaces- UART0: General purpose RS232 terminated in a 9 pin female DSUB connector which is also used to program LPC1768 Flash memory without external Programmer- UART1: General purpose RS485 terminated in a 3 pin male reliamate- UART2: General purpose RS232 terminated in a 3 pin male reliamate Interface to Controller internal ADC and DAC162 alphanumeric LCD and 12864 Graphic LCD display are provided one of them can be used at a time44 Key-MatrixSPI interface: Flash NVROM memory circuitSimple I2S demonstration circuitI2C interface: RTC ICEight general purpose LEDsFour-digit multiplexed 7-segment display interfaceInterface circuit for external InterruptInterface circuit for Capture & matchInterface circuit for PWM with a monitor LEDOn-board stepper motor, DC motor control, Relay interfaceInterface circuit for on board BuzzerEthernet interface with RJ45 female connector

LPC2148 1632 BIT ARM7TDMI-S with 512K bytes Program Flash, 42K bytes RAM12MHz Crystal allows easy communication setupOne on board voltage regulator for generating 3.3V. Input to this will be from External +5V DC Power supply through a 9-pin DSUB connectorOne RS232 interface circuits with 9 pin DSUB connector: this is used by the Boot loader program, to program LPC2148 Flash memory without external ProgrammerPiggy Back module containing LPC2148 controllerStandard JTAG connector with ARM 210 pin layout for programmingdebugging with ARM-JTAGStandard 26-pin FRC connectors to connect to on-board interface or some of ALS standard External InterfacesReset push-button for resetting the controllerSPI Interface: 2 channel ADC IC with POT and Temperature sensorI2C Interface: NVROM ICOn chip ADC interface circuitTwo External interrupt circuits with LED indicationLCD 162 alphanumeric displayOn-board eight push-button switches4x4 Key-Matrix connected to the port lines of the controllerEight general purpose LEDsFour-digit multiplexed 7-segment display interface8-bit DAC interfaceStepper motor interface with direction and speed controlDC motor interface with direction and speed controlInterface circuit for on board Buzzer and RelayA number of software examples in C-language to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL4 C compiler for ARMCompact elegant plastic enclosureSerial RS232 cable is includedOperates off 5V DC

Decade resistance box 5 dial range : 1 ohm to 100k ohmsdecade resistance box 6 dial range : 1 ohms to 1m ohmsdecade inductance box 5 dial range : 100 mh to 10hdecade inductance box 6 dial range : 10mh to 10hdecade capacitance box 5 dial range : 100pf to 10mfdecade capacitance box 6 dial range: 10pf to 10mf.

32 inputs using 8-way four DIP switches. Each input of these switches has an LED indication.32 outputs through output ports of FPGA connected to LEDs.16x2 AlphaNumeric LCD display with back-light through 10 PIN FRC Connectors to FPGACPLD port pins.Six-digit 7-segment displays connected through 10 PIN FRC connector to FPGACPLD port pins .4x4 key matrix.10 MHz, 5 MHz, 1MHz, 500 KHz, 100 KHz - five different clock frequencies.On-board Relay connected using 10 pin FRC to FPGACPLD port pins.On-board Traffic Light Simulator connected to FPGACPLD port pins using 16 pin FRC.On-board ADC connected to FPGACPLD port pins using 16 pin FRC.On-board DAC is provided to generate different waveforms and it is connected to FPGACPLD port pins using 16 pin FRC.On-board four level Elevator connected to FPGACPLD port pins using 16 pin FRC.Two-pin reliamate is provided on the board to connect external DC motor and it is connected to FPGACPLD port pins using 10 pin FRC.5-way PowerMate is provided to connect external stepper motor and it is connected to FPGACPLD port pins using 10 pin FRC.26-PIN FRC header with Cable for connecting to ALS standard interfaces.8 inputs using 0ne DIP switches. Each input of these switches has an LED indication.One push buttonFour sets of 20x2 female berg connector to plug the DAUGHTER BOARD

Modular Design: ARM9 daughter board and feature rich Motherboard.The SM-9302, daughter board, is actually an ARM9 SBC, with on boardUses EP-9302 ARM9 processorFlash 8 MBSDRAM 32 MBAlso IO and bus lines available on connector for further useEthernet connectivity through RJ45 connectorDual USB hostWorks on 5V, other voltages generated on board.Thus working as an independent unit, so can be used in ARM9 based projects4x4 Matrix keypad16x2 Lcd8 keys for digital ip8 LEDS for digital opI2C based RTCI2C 7 Segment DisplaySPI based EEPROMStepper Motor with driver interfacePOT for giving Analog inputTemperature sensor interfaceBSP provided with Lots of Examples. Example included webserver application.20 Pin Jtag ConnectorSerial port: 1 RS232, 1 RS485 port

The Cygnal Micro controller C8051F320 operating at a Frequency of 24MHz and a supply voltage of 3.3V.Universal Serial Bus (USB) Function Controller with eight flexible endpoint pipes, integrated transceiver, and 1k FIFO RAM.True 10-bit 200 kbps, 17-channel single-endeddifferential ADC analog multiplexer.16k bytes of on-chip FLASH memory, 2304 bytes of on-chip RAM.SMBusI2C, Enhanced UART, and Enhanced SPI serial interfaces implemented in hardware.On-chip Voltage Reference and Temperature Sensor.Four general-purpose 16-bit timers, PCA with five capturecompare modules and watchdog timer function.On-chip voltage reference and temperature sensor.On-chip voltage comparators (2).2521 Port IO (5V tolerant).