The Fully Encapsulated Trim Seal Butterfly valve design completely isolates body from the flowing media, thus eliminating the use of expensive body materials. Extended neck allows for adequate clearance of piping insulation and provide room for access to actuator mounting studs.

Self adjusting shaft seal of Trim Seal Butterfly valve is incorporated to prevent ingress of foreign material with the body shaft bore. The . double U cup design allows positive sealing in both directions and acts as a secondary shaft seal in emergency situations, while the Primary seal which is pre-loaded self compensating, synergistic primary seal, completely isolates the shaft from the flowing media and provides positive sealing at all angles of opening. An essential feature of the Butterfly Valve, the shaft busing absorbs side loads applied to the disc by the flowing media and for eccentrically mounted actuators.

AMCO TRIM SEAL is maintenance free Fit it and Forget it, Mount it any position for flow in either direction.

• Water Treatment


• Chemical Industries


• Desulphurisation Plants


• Paper Industry


• Sugar Industry


• Construction Industry


• Drilling Rigs


• HVAC


• Cooling Water Circulation


• Pneumatic Conveyors


• Compressed Air


• Waste Effluent Treatment Plants


• Gas Plants

the short face to face dimensions and the low weight guarantee a simple and space saving installation between bolts of connecting flanges, flange sealing is obtained by o-rings, hence no gaskets required.

body & disc:

cast iron is 210 gr. Fg 260
cast steel astm a216 gr. Wcb
cast stainless steel astm a351 gr. Cf8/cf8m
aisi 304 & 316

seat / body o rings:

nitrile, epdm, viton, silicone, ptfe other materials available on special request.

AMCO Knife Edge Gate Valves are designed for Isolation, On-Off, and Throttling services In Paper & Pulp Industries, Power Plants, Steel Plants, Cement Plants, Sugar Industries, Chemical & Textile Processing Industries, Mining, Water and Sewage Plants to handle Slurries, Slag, Pulp and Fibrous Material, Fly Ash, Powders, Clean or Corrosive gases.

Almost every know fluid in industry throughout the world can be, and is, handled by the diaphragm valve.

Diaphragm Valves are particularly suitable for service lines Handling Corrosive, Abrasives, Viscous or Fibrous Fluids.

ADVANTAGES OF DIAPHRAGM VALVES

1. The most economical corrosion/abrasion resisting valve available today.

2. Permanent bubble tightness against slurry, fibre and gases. Resilient closure.

3. No contamination. The most suitable for Nuclear & Food Service.

4. No Gland Packing.

5. Simple In Line maintenance.

Easy dismantling and assembly possible without removing the body from pipeline.

AMCO DIAPHRAGM VALVES A UNIQUE DESIGN SEALED FROM THE SERVICE AND PROOFED AGAINST CORROSION AND EROSION IN HOSTILE ENVIRONMENTS.

You do not have to pay a Premium for Quality

AIV BFV10 Model Butterfly Valveincorporates the optimum design features to provide long trouble free service in the field. This general purpose soft seated Butterfly valve has a fully rubber lined single piece body with centric disc construction and is available in wafer type body pattern.

The body liner which also functions as the soft seat, comes in either a replaceable version or an integrally molded (bonded) version and offers 100% bi-directional sealing against vacuum to rated pressure of PN 10 or PN 16.

The wafer style body has universal design to fit between pipe flanges of almost all popular flange standards.

Disk Check Valves must be fitted in accordance with the direction of flow arrow indicating correct fluid flow direction. When fitted with a spring they can be installed in any plane. when supplied without a spring these must be fitted in a vertical with the follow from bottom to top. The cam design of the body allows the various flange types to be accommodated. The body is rotated to touch the flange joint bolts ensuring that a good joint is obtained.

AMCO General purpose Disc Check Valves are best used in :

• Delivery line of pumps


• Steam and condensate systems


• Vessels as foot valves


• Filtration and ion-exchange process


• Refrigeration plants and air conditioning systems


• Airline, water, & effluent plants, corrosive liquids and gases.

SPECIAL DESIGN FEATURES

ROBUST > LIGHT WEIGHT > COMPACT > ECONOMICAL

• Quick open and close action.


• Can be mounted both vertical or horizontal position.


• Low pressure drop.


• High Cv value.


• Soft seated options available.

Dual Plate Check Valves has become popular worldwide and a priced invention along with Butterfly Valves & Ball Valves. In this Century, AMCO utilize their past experience in the field and brings to its esteemed customers, just another marvelous product with Superior Technology. Thus developed by us consists of a Wafer Type Body, Plates equipped with inlayed seal in a dove tail groove on body seat, corrosion spring and pin provided internally. The Valve is so compact that the face to face may be reduced to about 25% and weight to about 20% when compared to convention swing type check valves, which are not only bulky, expensive and difficult to maintain, but also less durable.

Salient Features :

• No water hammer and slamming


• Compact and structurally sound design


• Can be installed horizontally, vertically or in an incline


• Low pressure drop and reduced energy loss irrespective of pressure ratings


• Efficient and positive sealing under most flow and pressure conditions


• Easy to maintain, long life and trouble free operation

Technical Features :

• Twin plate, flat seat design for efficient sealing


• Long Leg spring(s) allows the plates to open and close without seat scrubbing


• Valves with 350 mm and larger are fitted with independent spring(s) as a standard feature


• Lower head loss than swing check valves above 150 mm


• Valves with soft seats have bubble tight closure to API 6D


• Simplicity of Installation is a key featureYou do not have to pay a Premium for Quality

The Fully Encapsulated Trim Seal Butterfly valve design completely isolates body from the flowing media, thus eliminating the use of expensive body materials. Extended neck allows for adequate clearance of piping insulation and provide room for access to actuator mounting studs.

Self adjusting shaft seal of Trim Seal Butterfly valve is incorporated to prevent ingress of foreign material with the body shaft bore. The . double U cup design allows positive sealing in both directions and acts as a secondary shaft seal in emergency situations, while the Primary seal which is pre-loaded self compensating, synergistic primary seal, completely isolates the shaft from the flowing media and provides positive sealing at all angles of opening. An essential feature of the Butterfly Valve, the shaft busing absorbs side loads applied to the disc by the flowing media and for eccentrically mounted actuators.

AMCO TRIM SEAL is maintenance free Fit it and Forget it, Mount it any position for flow in either direction.

• Water Treatment


• Chemical Industries


• Desulphurisation Plants


• Paper Industry


• Sugar Industry


• Construction Industry


• Drilling Rigs


• HVAC


• Cooling Water Circulation


• Pneumatic Conveyors


• Compressed Air


• Waste Effluent Treatment Plants


• Gas Plants

the short face to face dimensions and the low weight guarantee a simple and space saving installation between bolts of connecting flanges, flange sealing is obtained by o-rings, hence no gaskets required.

body & disc:

cast iron is 210 gr. Fg 260
cast steel astm a216 gr. Wcb
cast stainless steel astm a351 gr. Cf8/cf8m
aisi 304 & 316

seat / body o rings:

nitrile, epdm, viton, silicone, ptfe other materials available on special request.

AMCO Knife Edge Gate Valves are designed for Isolation, On-Off, and Throttling services In Paper & Pulp Industries, Power Plants, Steel Plants, Cement Plants, Sugar Industries, Chemical & Textile Processing Industries, Mining, Water and Sewage Plants to handle Slurries, Slag, Pulp and Fibrous Material, Fly Ash, Powders, Clean or Corrosive gases.

Almost every know fluid in industry throughout the world can be, and is, handled by the diaphragm valve.

Diaphragm Valves are particularly suitable for service lines Handling Corrosive, Abrasives, Viscous or Fibrous Fluids.

ADVANTAGES OF DIAPHRAGM VALVES

1. The most economical corrosion/abrasion resisting valve available today.

2. Permanent bubble tightness against slurry, fibre and gases. Resilient closure.

3. No contamination. The most suitable for Nuclear & Food Service.

4. No Gland Packing.

5. Simple In Line maintenance.

Easy dismantling and assembly possible without removing the body from pipeline.

AMCO DIAPHRAGM VALVES A UNIQUE DESIGN SEALED FROM THE SERVICE AND PROOFED AGAINST CORROSION AND EROSION IN HOSTILE ENVIRONMENTS.

You do not have to pay a Premium for Quality

AIV BFV10 Model Butterfly Valveincorporates the optimum design features to provide long trouble free service in the field. This general purpose soft seated Butterfly valve has a fully rubber lined single piece body with centric disc construction and is available in wafer type body pattern.

The body liner which also functions as the soft seat, comes in either a replaceable version or an integrally molded (bonded) version and offers 100% bi-directional sealing against vacuum to rated pressure of PN 10 or PN 16.

The wafer style body has universal design to fit between pipe flanges of almost all popular flange standards.

Disk Check Valves must be fitted in accordance with the direction of flow arrow indicating correct fluid flow direction. When fitted with a spring they can be installed in any plane. when supplied without a spring these must be fitted in a vertical with the follow from bottom to top. The cam design of the body allows the various flange types to be accommodated. The body is rotated to touch the flange joint bolts ensuring that a good joint is obtained.

AMCO General purpose Disc Check Valves are best used in :

• Delivery line of pumps


• Steam and condensate systems


• Vessels as foot valves


• Filtration and ion-exchange process


• Refrigeration plants and air conditioning systems


• Airline, water, & effluent plants, corrosive liquids and gases.

SPECIAL DESIGN FEATURES

ROBUST > LIGHT WEIGHT > COMPACT > ECONOMICAL

• Quick open and close action.


• Can be mounted both vertical or horizontal position.


• Low pressure drop.


• High Cv value.


• Soft seated options available.

Dual Plate Check Valves has become popular worldwide and a priced invention along with Butterfly Valves & Ball Valves. In this Century, AMCO utilize their past experience in the field and brings to its esteemed customers, just another marvelous product with Superior Technology. Thus developed by us consists of a Wafer Type Body, Plates equipped with inlayed seal in a dove tail groove on body seat, corrosion spring and pin provided internally. The Valve is so compact that the face to face may be reduced to about 25% and weight to about 20% when compared to convention swing type check valves, which are not only bulky, expensive and difficult to maintain, but also less durable.

Salient Features :

• No water hammer and slamming


• Compact and structurally sound design


• Can be installed horizontally, vertically or in an incline


• Low pressure drop and reduced energy loss irrespective of pressure ratings


• Efficient and positive sealing under most flow and pressure conditions


• Easy to maintain, long life and trouble free operation

Technical Features :

• Twin plate, flat seat design for efficient sealing


• Long Leg spring(s) allows the plates to open and close without seat scrubbing


• Valves with 350 mm and larger are fitted with independent spring(s) as a standard feature


• Lower head loss than swing check valves above 150 mm


• Valves with soft seats have bubble tight closure to API 6D


• Simplicity of Installation is a key featureYou do not have to pay a Premium for Quality