Apollo Valves & Pipes

Ankleshwar, Ankleshwar, Gujarat

Features:

• Swing check type design
• Rigid and sturdy design with minimum head loss
• Long service life and leak-tightness of high order
• Suitable for clear water having turibidity upto 3000 o ppm and temperature of 65 Centigrade (rubber to o bronze / stainless steel seating) and upto 95 Centigrade (Bronze/ bronze, stainless steel / stainless steel seating

Applications:

• Used in waterworks piplines to reduce water hammer effect
• Preventing back flow of water to the pump

Specifications:

• Manufacturing Standard BS 5153 (EN 12334) / IS 5312 Part 1 & 2
• Size Range 40 to 1500 mm
• Pressure Ratings PN6, PN10, PN16
• End Connection Flanged
  

Features:

• Internationally patented design for minimum loss of live steam
• Multi-concept, high energy saving, efficient impulse cum themodynamic steam trapping device
• Ends - Flanged / Screwed

Applications:

• For every industry using steam lines

Specifications:

• Manufacturing Standard : ISO 6552
• Size Range: 15, 20 and 25 mm
• Ends Flanged / Screwed

Features:

• Double Orifice Type (Small and large orifice), kinetic type
• Single air valve
• Non clogging and self sealing balls for trouble free operation
• Totally tamper proof kinetic air valve series available.
• Suited for turbid or clear water sewage; releasing air when water mains are being filled and admitting air while being emptied.
• Cuts loss of water when water mains are full Releasing air accumulated under pressure in pipe during normal conditions.

Applications:

• Water Supply Lines / Distribution Lines
• Clear Water and sewage applications

Specifications:

• Manufacturing Standard IS 14845
• Size Range 50 to 200 mm
• Pressure Ratings PN6, PN10, PN16, PN 20

Features:

• Double Orifice Type (Small and large orifice), kinetic typeSingle air valveNon clogging and self sealing balls for trouble free operationTotally tamper proof kinetic air valve series available.Suited for turbid or clear water sewage; releasing air when water mains are being filled and admitting air while being emptied.Cuts loss of water when water mains are full Releasing air accumulated under pressure in pipe during normal conditions.

Applications:

• Water Supply Lines / Distribution Lines
• Clear Water and sewage applications

Specifications:

• Manufacturing Standard IS 14845
• Size Range 50 to 250 mm
• Pressure Ratings PN6, PN10, PN16

Features:

• Swing check type, Double flanged /butt weld end, bolted cover design
• Rigid and sturdy design with long service life

Applications:

• Naptha and naptha derivatives in oil refineries
• Water, steam, air, gas and liquids having corrosive properties
• Suitable for wide range of working conditions of pressures and tempertaure ratings

Specifications:

• Manufacturing Standard : BS 1868
• Size Range and Pressure Rating : 25 to 700 mm : Class 150 65 to 700 mm : Class 300 100 450 mm : Class 600
• End Connection : Flanged

Features:

• Rigid and sturdy design with minimum loss of head across the valve
• Perfectly flat seating surfaces for good sealing
• Preventing entry of foreign body to pump through suction pipe
• Long service life

Applications:

• Used in suction side of pump to avoid flow reversal from pump to sump with monobloc pumps

Specifications:

• Manufacturing Standard IS 4038
• Size Range 50 to 600 mm
• Pressure Rating PN 2

• Double rack & pinion
• High corrosion resistance
• Pinion supported on polyacetal bearings
• Maximum working pressure 10bar
• Lubrication not required
• Life more than 1 million cycles
• Antiblow out pinion
• Can be converted to single acting by just adding springs

• Bifunctional version
• High flow rate, kv=12(lpm@1bar), Fast response time
• Minimum operating pressure required
• Suitable for air, gases water etc.
• Ideally suited for double acting actuator on ON/OFF & control duty
• Special versions may be developed on request
• Poppet Design
• Accessories for mounting the solenoid valve on the actuator are provided.
• Solenoid of any voltage rating/construction can be replaced at customer's end
• External pilot air operated available

• Teflon coated Rubber, EPDM Rubber, Viton Rubber on request

• PP (POLYPROPYLENE)
• HDPE (HIGH DENSITY POLYETHYLENE)
• ISOTACTIC PP
• PVDF (POLYVINYLIDENE FLUORIDE

• Teflon coated Rubber, EPDM Rubber, Viton Rubber on request

• PP (POLYPROPYLENE)
• HDPE (HIGH DENSITY POLYETHYLENE)
• ISOTACTIC PP
• PVDF (POLYVINYLIDENE FLUORIDE)

• PP (POLYPROPYLENE)
• HDPE (HIGH DENSITY POLYETHYLENE)
• ISOTACTIC PP
• PVDF (POLYVINYLIDENE FLUORIDE)

Features:

• Metal to metal seating for longer service life
• Rigid and sturdy design with minimum loss of head across the valve
• Accurate interchangeability of components
• Accurate parallelism between side flanges
• Equal taper between wedge faces
• Perfect machining and press fitting of body and wedge rings
• Excellent finish on spindle threads resulting in low friction and smooth operation of valves
• Leak-tightness even after thousands of Open / Close

Applications:

• Fire service water control valves

Specifications:

• Manufacturing Standard IS 14846
• Size Range 50 to 250 mm
• Pressure Rating 250 PSI
• End Connections Flanged

Features:

• Rigid and sturdy design with minimum loss of head across the valve
• Compact, light weight, low operating torques
• Eccentric seat geometry results in less wear and tear and longer life
• Self cleaning and non jamming seat design
• Gas tight shut-off
• Self energizing seating design
• Combined 'O' ring and 'U' cup seating on shaft
• Through flow disc design for large size Butterfly Valves

Applications:

• Water works
• Power plants
• Sewage plants
• Process industries
• Chemical and petrochemical plants

Specifications:

• Manufacturing Standard BS 5155 (BS EN 593)/ AWWA C504/ IS 13095
• Size Range 50 to 4500 mm
• Pressure Ratings PN6, PN10, PN16, PN20
• Class -75, 150, 250
• End Connection Double Flanged