The Roller Bearing 'V' Blocks are accurately assemble and precision ground on the bottom taces. Four high precision ball bearing on the top. Thus, providing self aligning wearing hard accurate supports which will not damage even the most delicate work piece. "Crystal" Roller Bearing 'V' Blocks are very useful in tool room, machine shop, assembly, inspeciton, for checking and marking odd shapes jobs, crank-shafts etc.

The highest separating capacity is ensured by two rails on the magnetic polar surface. You can separate press blanks or material with irregular shapes in certain intervals. Suitable for separating oil stuck sheets or heavily piledup sheets which are difficult to separate manually. Compact type with highly efficient Ferrite Magnet.

Low height Made from high quality steel. Hardened & Ground to 58 Rc An angle can be set to within ± 5 seconds of degree. Firm Hinge Clamps reduce possibility of distortion Flatness 0.005 mm per 100 mm. Tapped hole in top, sides & end, facilitate clamping. Suitable for 0-45 degree Capacity.

A power permanent Magnetic Base hold firmly to any steel or iron surface-horizontally, vertically or up- side down, thus, eliminating time spent on clamping indicator to machine The dial gauge can be locked in any desired position with single lock (Centralised clamping) The clamping hole intended for dia 8 mm stem and dovetail clamp for dial test indicator. Fine Adjustment is provided. The clamping is very easy and smooth as same is achieved by operating the centralized Knob.

There is no risk, when power fails. The de-magnetization cycle of Electoperm Magnetic chuck eliminates possible residual magnetism in the workpiece, therefore easy release for high alloy steel parats. They are designed for heavy operation such as milling cut of 3 to 6 mm depth at recommended speed & feed.

It helps the user for easy handling & storage. Our racks are available in different lengths and are totally protected from rust and corrosion. Racks are easily mounted and all available magnetic flux from a small number of magnets is concentrated in the two mild steel pole pieces helps ‘Crystal’ Racks make best possible use of permanent magnet material, in lifting and holding problems that can be easily solved.

The highest separating capacity is ensured by two rails on the magnetic polar surface. You can separate press blanks or material with irregular shapes in certain intervals. Suitable for separating oil stuck sheets or heavily piledup sheets which are difficult to separate manually. Compact type with highly efficient Ferrite Magnet.

The Roller Bearing 'V' Blocks are accurately assemble and precision ground on the bottom taces. Four high precision ball bearing on the top. Thus, providing self aligning wearing hard accurate supports which will not damage even the most delicate work piece. "Crystal" Roller Bearing 'V' Blocks are very useful in tool room, machine shop, assembly, inspeciton, for checking and marking odd shapes jobs, crank-shafts etc.

EPM lifters are a breakthrough technology as compared to the conventional lifters. EPM Lifters are “COLD” devices, also they do not require a continuous electrical supply, except only for a few seconds – in activation and deactivation. So when in operation, electrical supply is not essential for lifting the required load and thereby eliminating risks associated with power failure.

Low height Made from high quality steel. Hardened & Ground to 58 Rc An angle can be set to within ± 5 seconds of degree. Firm Hinge Clamps reduce possibility of distortion Flatness 0.005 mm per 100 mm. Tapped hole in top, sides & end, facilitate clamping. Suitable for 0-45 degree Capacity.

There is no risk, when power fails. The de-magnetization cycle of Electoperm Magnetic chuck eliminates possible residual magnetism in the workpiece, therefore easy release for high alloy steel parats. They are designed for heavy operation such as milling cut of 3 to 6 mm depth at recommended speed & feed.

A power permanent Magnetic Base hold firmly to any steel or iron surface-horizontally, vertically or up- side down, thus, eliminating time spent on clamping indicator to machine The dial gauge can be locked in any desired position with single lock (Centralised clamping) The clamping hole intended for dia 8 mm stem and dovetail clamp for dial test indicator. Fine Adjustment is provided. The clamping is very easy and smooth as same is achieved by operating the centralized Knob.