Other Products / Services #5909248

The modular workstation for any number of persons with work surface of any size with half height

partition should comprise of:

a) for 70 mm (of height 4' and thickness and minimum overall thickness of 70

mm) made of :

i) Structural members fabricated of 1.50 mm to 2.20 mm pure 100% aluminium

extrusion channel with epoxy / powder coating min. of 40 to 50 micron.

ii) Two sides of partition panels finished partially with 9 mm thick prelaminated particle

board and in between space of 52 mm out of over all thickness of 70 mm to be kept

vacant for universal data and cable management system. Partial panel may be with

glass panel of minimum thickness 5mm. for some areas for better visibility and

lighting.

iii) Box type raceways open able on both sides at bottom level and as required below or

above table height for carrying electrical and data cables. Skirting covers of height

120 130 mm with materials fabricated with prelaminated particle board of

thickness 9mm.

iv) Slots in vertical sides for horizontal wire management of cables.

v) General: Trims finish Aluminium epoxy coated with 40-50 micron. All metal

sections, cantilever brackets to hold the work tables and tops and aluminium profile

finished in epoxy coating of thickness 45 to 50 micron of approved shade.

for 30 mm- The entire structural frame viz. horizontals and verticals are made of 30mm

thick high quality aluminum extruded interlocking sections. Semi-circular top and

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual

management facility is available. As per the international standards corner caps and

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness

in the flooring. Snap fit tiles compromises of 15 mm prelam board on both making 30

mm thick over all, Magnetic Fabric board. 30mm snap fit panel fixtures are made of

zinc moulds. The top, vertical and corner trims are available in standard powder

coating finish of international standards. ( Decor-x make )

for 60 mm- The entire structural frame viz. horizontals and verticals are made of 60mm

thick high quality aluminum extruded interlocking sections. Semi-circular top and

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual

management facility is available. As per the international standards corner caps and

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness

in the flooring. 60mm snap fit panel fixtures are made of zinc moulds. The top,

vertical and corner trims are available in standard powder coating finish of

international standards. ( Decor-x make )

for 50 mm- The entire structural frame viz. horizontals and verticals are made of 50mm

thick high quality aluminum extruded interlocking sections. Semi-circular top and

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual

management facility is available. As per the international standards corner caps and

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness

in the flooring. Snap fit tiles compromises of 4 mm prelam board on both side

making 48 mm thick over all, Magnetic Fabric board . 50mm snap fit panel fixtures

are made of zinc moulds. The top, vertical and corner trims are available in standard

powder coating ( moon shell grey ) finish of international standards.

Top: 75 mm thick MDF PVC foiled with openable central top.

Legs: 200 mm Thick Box Type MDF PVC Foiled

Modesty: 18 mm Melamine edge banded.

i) Top fabricated out of 25 mm thick Plain Particle Board interior grade conforming to IS12823 : 1990 and the top with laminate of thickness 0.7 mm of approved brand & shadeand glue of PVAC. All components like tops, sides etc. are finished with machine pressed2mm thick PVC lipping glued with hotmelt EVA glue.

ii) Bottom, sides, shelves and shutters (openable) are fabricated out of 18 mm prelaminated(both sides) particle board and the back of 9 mm prelaminated (both sides) board.

iii) Lock and stoppers.

iv) Edges finishes with required PVC EDGE binding tape glued with hot melt EVA glue.

For 70 mm (of height 4' and thickness and minimum overall thickness of 70mm) made of :

i) Structural members fabricated of 1.50 mm to 2.20 mm pure 100% aluminiumextrusion channel with epoxy / powder coating min. of 40 to 50 micron.

ii) Two sides of partition panels finished partially with 9 mm thick prelaminated particleboard and in between space of 52 mm out of over all thickness of 70 mm to be keptvacant for universal data and cable management system. Partial panel may be withglass panel of minimum thickness 5mm. for some areas for better visibility andlighting.

iii) Box type raceways open able on both sides at bottom level and as required below orabove table height for carrying electrical and data cables. Skirting covers of height120 130 mm with materials fabricated with prelaminated particle board ofthickness 9mm.

iv) Slots in vertical sides for horizontal wire management of cables.

v) General: Trims finish Aluminium epoxy coated with 40-50 micron. All metalsections, cantilever brackets to hold the work tables and tops andaluminium profilefinished in epoxy coating of thickness 45 to 50 micron of approved shade.

For 30 mm- The entire structural frame viz. horizontals and verticals are made of 30mmthick high quality aluminum extruded interlocking sections. Semi-circular top andvertical trims are made of aluminum extrusions which are snap fit. Provision of dualmanagement facility is available. As per the international standards corner caps andtop caps are made of Zinc moulds. Levelers are provided to overcome unevennessin the flooring. Snap fit tiles compromises of 15 mm prelam board on both making 30mm thick over all, Magnetic Fabric board. 30mm snap fit panel fixtures are made ofzinc moulds. The top, vertical and corner trims are available in standard powdercoating finish of international standards. ( Decor-x make )

For 60 mm- The entire structural frame viz. horizontals and verticals are made of 60mmthick high quality aluminum extruded interlocking sections. Semi-circular top andvertical trims are made of aluminum extrusions which are snap fit. Provision of dualmanagement facility is available. As per the international standards corner caps andtop caps are made of Zinc moulds. Levelers are provided to overcome unevennessin the flooring. 60mm snap fit panel fixtures are made of zinc moulds. The top, vertical and corner trims are available in standard powder coating finish ofinternational standards. ( Decor-x make )

For 50 mm- The entire structural frame viz. horizontals and verticals are made of 50mmthick high quality aluminum extruded interlocking sections. Semi-circular top andvertical trims are made of aluminum extrusions which are snap fit. Provision of dualmanagement facility is available. As per the international standards corner caps andtop caps are made of Zinc moulds. Levelers are provided to overcome unevennessin the flooring. Snap fit tiles compromises of 4 mm prelam board on both sidemaking 48 mm thick over all, Magnetic Fabric board . 50mm snap fit panel fixturesare made of zinc moulds. The top, vertical and corner trims are available in standardpowder coating ( moon shell grey ) finish of international standards.

b) Work surfaces made of:

i. Top fabricated out of 25 mm thick Plain Particle Board interior grade

ii. Key Board Drawer: Key Board Drawer will be fabricated from 18 mm thick

iii. CPU trolley: Should be made of CRCA sheet and finishing will be in epoxy coating

iv. Pedestal unit ( 450 mm x 50mm x 737 mm ht.): Should consist of two small drawerIS 12823 : 1990 and the top with laminate of thickness 0.7 mm approved brand &shade & bottom with balancing laminate. All components like tops, sides etc. arefinished with machine pressed 2mm thick PVC EDGE binding tape glued with hotmelt EVA glue.These work surfaces are mounted either on panels or supported one end by boardside or metal side and other end on panel. ii. Board sides are fabricated out of 18mm thick Prelaminated (both sides) Particle board.

Prelaminated Particle board with high quality telescopic channel mounted from thetable bottom.of thickness 40-50micron. . It should be mounted on Castors.and one filling drawer and should be fabricated out of 18 mm prelaminated particleboard and assembled with drawer runner ( METABOX Systems) for smoothoperation. The entire unit should be provided with central locking system.

Top: 36mm thick MDF PVC foiled top with decorative Anodized Sections.

Legs: Curved Shape PVC foiled with 100 mm Thickness at Center.

Modesty: 18 mm Thick Pre-lamineted.

Cabinetry 18 mm Thick PVC foiled MDF.

Shutters: 18 mm thick PVC foiled MDF.

SS. Thumb Knob.