Asian Test Equipments - Testing Equipment

Bursting Strength Tester of any material such as fabric, leather, paper, paperboard & corrugated box etc. It's strength under multi-directional force and is defined, as the hydrostatic pressure required producing rapture of the material when pressure is applied at a controlled increasing rate through a rubber diaphragm.

ASIAN Limited Oxygen Index Apparatus consists of a test chimney made of borosilicate glass suppurated by the metallic base and hook with the help of the metallic pillar. The mixture of nitrogen and oxygen is released from the bottom of the tube. The tube is filled with glass beads for mixing and evenly distributing the gas mixture. The specimen holder, which holds the test specimen, made of U shape and fixed at the center of the chimney. There is the porous screen mounted below the level of the specimen holder, to prevent falling combustion debris from fouling the gas entry and distribution paths. There is a digital temperature indicator cum controller with a thermocouple for the measurement. A copper tube with a suitable orifice for pilot flame is provided for igniting the specimen by inserting it from the top of the test column. The digital preset timer and buzzer are also mounted in the instrument. Two rotameter with needle valve is provided to control and measure oxygen and nitrogen flow in the test chimney. A timer for indicating the time of burning with a reset switch. The rotameter, temperature controller, timer are fitted in the sheet panel. The test chimney is fitted separately on the metallic platform. Gasses, gas cylinders and its fittings are not provided with the equipment and have to be arranged by the purchaser.

ASIAN Smoke Density Tester is constructed using 14 gauge aluminum box, which is hinged a heat resistant glass glazed door. This box is mounted on the base which houses the controls. Dependent upon the materials tested, the metal may require protection from corrosion. The chamber is sealed except for 25 by 30mm (1by 9in.) openings on the four sides of the bottom of the chamber. A liters/min specified capacity blower is mounted on one side of the chamber. The inlet duct to the bowler is equipped with a close fitting damper. The outlet of the bowler will be connected through a duct to the laboratory exhaust system. The two sides adjacent to the door are fitted with 70mm (2/3in) diameter smoke tight glazed areas entered 480mm (19/4 in.) above the base. At these locations and outside the chamber, boxes containing the optical equipment and additional controls are attached. A removable white plastic plate is attached to the back of the chamber. There is a clear area centered above the bottom of the chamber. Through which is seen an illuminated white on the red exit sign. The white background permits observations of the flame, smoke, and burning characteristics of the materials. The viewing of the exit sign helps to correlate visibility and measured values. The specimen holder is supported on a square gauge. Stainless steel wire cloth above the base and equidistant from all sides of the chamber. This screen is lying in a stainless steel bezel supported by a rod through the right side of the chamber. From the same rod similar bezel is located below and it supports a square of asbestos paper which catches any particles that may drip from the specimen during the test. By rotating the specimen holder rod, the burning specimen can be quenched in a shallow pan of water positioned below the specimen holder.

The specimen is ignited by a propane flame from a burner operating at a specified pressure. The fuel is mixed with air which has been propelled through the burner by the venturi effect of the propane as it passes through a small orifice. The burner is designed to provide adequate outside air. the burner is capable of being positioned quickly under the specimen so that the exit of the burner falls on a line passing through a point 8mm above the base at one corner of the chamber extending diagonally across the chamber and sloping upwards at 45 deg with the base. There is a control panel which controls and indicate the supply of gas. Lux of the light measurement system of the mounted light source also mounted in the instrument. There is a digital timer mounted in the instrument to indicate the time.

The Fogging Tester is specially designed equipment for testing the fogging characteristics or VOCs of leather, plastics, vinyl and textiles for automotive, aerospace and other transportation vehicles.This fogging tester comprises of following equipment.

TheDRY SAND ABRASION TEST RIGhas been designed as per ASTM G 65 specifications. This test uses a rubber-rimmed wheel as the bed for silica abrasive that is fed from a hopper by a nozzle between the sample and the wheel. The sample is pressed into the wheel by a dead weight loaded lever. The test is run for a set number of revolutions with automatic cutoff and the wear is measured by measuring the volume of material lost through mass loss and density measurements. The flow of sand into the gap between the surfaces is controlled by the geometry of the nozzle that must be very carefully defined to obtain the required sand flow rate. The abrasive only passes through the wear interface once and is thrown away at the end of the test. The uniform loading and uniform flow of abrasive into the gap between wheel and the specimen under controlled conditions give consistent results. The properties of the rubber lining of the wheel also have a major effect on the results and need to be carefully controlled.

The Horizontal Flammability Tester for the interior of a motor vehicle consists of a stainless steel box. The box has four slots of specified width on the upper part of all sides and the bottom plate has 10holes of specified diameter. The box has an access window of a heat resistant glass plate on the front and a door that has a slot that allows U-shaped clamp enter the box, and a hole for passing a hose from a gas burner, on the side. The box is fitted with four legs and the bottom part raised by 10mm. the clamps made of metal of U-shape of a specified dimension. A Bunsen burner of specified dimension is fitted on the bottom of the stainless steel box. The length of flame control with the help of the needle valve. The flame of the burner is automatically controlled with the help digital preset timer and synchronous motor.

tensile strength tester and elongation are the two prime characteristics of most of the raw materials, whether they are metals or non-metals such as foam, rubber, textiles, plastic, paper or finished products such as rods, wires, ropes, yarns, belts etcetera. These properties very often play the major role in determining the suitability of any raw material for any specific application. It is, therefore, of utmost importance to determine these characteristics accurately, conveniently, and quickly.

We manufacturer Compressibility and Recovery Tester as per ASTM F 36

AsianMelt Flow Index Testerfor plastic measures the melt flow index of the plastic material. The system consists of a heated extruder tube, an interchangeable jet through which the material under test is extruded, and a piston with dead weights to apply the specified pressure on the material inside the extruder tube. The extruded tube is made from carbon steel and is heated by means of a Bend Heater, which surrounds its outer circumference. A PID controller is provided to indicate & control the temperature of the tube. The heater clogged with mineral wool insulation. The assembly is fixed on a rigid stand. The bottom of the tube is lagged with an insulation of PTFE to prevent sticking of the extrudate. The jet through with the extruder is pushed out is made from hardened and ground die steel. It is held at the bottom of the extruder tube. The piston made from silver steel relieved at the upper end is provided to push the extrudate out of the jet. The piston moves inside the cavity of the tube. A sleeve to provide to guide the relieved portion of the piston. The top of the piston carries a plate-form for keeping the load on. The plate-form is thermally insulated from the load. The extruder tube assembly is mounted on a metal box. A sheet metal control panel is mounted on the side of the equipment & houses the PID Controller, DIGITAL PRESET TIMER & other electronic components. Cleaning tools for tube cavity and jets & stoppers & cutter for the extrudate are also supplied with the equipment.

In the market, we present a highly functional range of Wood Testing Equipments with excellent accuracy. These testing machines offer a complete spectrum of testing jobs in various industries like wooden, automotive, aerospace, paints, aviation, and many others. We have in our universal testing machines for determining the shear strength, compression strength and elongation of varied materials. Then, there is humidity chamber for maintaining the standing temperature and humidity level to get accurate properties of the test specimen. Fore testing the gloss and brightness of any objects surface, we have gloss meter. We have all the latest versions of this testing equipment, all in confirmation with the international standards of ASTM D412, D395, D429, GB 9754, IS 3400 and ISO 2813.

Specifications:

• Model: ATE/UTM/60C
• Straining/ piston speeds (mm/mm) (at no load): 0-150
• Resolution of piston movement (mm): 0.1
• Clearance for tensile at fully descended working piston (mm): 50-700
• Clearance for compression test at fully descended working piston (mm) Clearance between columns (mm): 0-700, 500

Connected Load:

• HP: 3
• V: 400-440
• Phase: 3

Dimensions:

• LXWXH in (Inch): 72 x 30 x 82 (approx.)
• Net Weight in (kg): 1700 (approx.)
• Gross Weight in (kg): 2000 (approx.)

Standard Accessories:

• Clamping jaws for round specimen diameter (mm): 10-25, 25-40 & 40-55
• "Clamping jaws for flat specimens thickness (mm) Width: 0-15, 15-30, 70

For Compression Test:

• Pair of compression plates of diameter (mm): 120

For Flexural Test:

• Table with adjustable rollers, width of rollers (mm): 160
• Diameter of the rollers (mm): 50
• Max. the clearance between supports: 600
• Radius of punch tops (mm): 16, 22

Our company has brought a revolution in the spring and wire forming industry with advanced Spring Testers. With this machine, we provide cutting edge and non-destructive testing solutions to several industries. This is specifically developed to support industries continual efforts in manufacturing the better product at a lower cost. The offered testers are used for geometrical inspection of 2D and 3D wire formed parts.

The ASIAN Analog Bursting Strength Tester is designed to find bursting strength of fabric/ leather/ paper/paperboard & corrugated box. A test specimen is held between two annular clamps under sufficient pressure to minimize slippage. The upper clamping surface which is in contact with the test specimens has continuous spiral grooves. A circular diaphragm of pure gum rubber is clamped between the lower clamping plate & pressure cylinder so that before the diaphragm is stretched by pressure underneath it the center of its upper surface. The equipment is fitted with a motor driven cam mechanism, which increases fluid displacement on the lower side of the diaphragm at a specified rate. The equipment is fitted with an arrangement, which automatically brings down the pressure and stops the motor on completion of the test cycle. A maximum reading type pressure gauge gives the bursting pressure. The equipment is ruggedly designed to give a long & trouble free life. The components are brighter chrome plated or painted in metallic paint to give the tester an aesthetic appearance. Digital type pressure gauge type instruments are also available. Digital type pressure gauge with pneumatic clamping model also available.

We manufacture all type of fabric testing equipments.