Aviation Tech Tools

Manjalpur, Vadodara, Gujarat

For the convenience of the clients, we have adopted safe and secure payment gateway that helps us in the attainment of complete client satisfaction and maintaining transparency in dealings. To pack our products, we have ultramodern machines. The packaging materials are nontoxic, sturdy and reliable. The products remain safe and undamaged in our packaging.

Feature
Heat Resistant BodyThe body of the tool is made from a special alloy steel that has high heat resistant properties.A special surface treatment is used to increase wear and corrosion resistance.

2 Insert Bottom Cutting EdgeThe lower cutting edge consists of 2 inserts, resulting in higher cutting edge strength and increased tool life.

One Insert TypeTool management is simplified by using only one type of insert for all 4 cutting edges. By rotating the inserts it’s possible to use all 4 corners.

Center Cutting EdgeThe AQX is designed with a center cutting edge, making it possible to sink, helical mill and pocket without a pre-prepared hole.

Through Coolant HolesThe body is designed with through coolant holes toãimprove cooling and chip disposal. The AQX is also available without coolant holes.

Short Edge TypeAn economical short edge type body is available with only 2 inserts for short depth of cut applications.

Undercut TypeThe cutting edge diameter DC has been designed so it is larger than the shank diameter DCON, making it possible to machine vertical faces without any interference.
New PVD Coated Grades MP6100/MP7100/MP9100

• Wide range of grades for specific materials MIRACLE SIGMA accumulated Al-Ti-Cr-N based PVD coating

• TOUGH-Σ Technology
  • A fusion of the separate coating technologies;
  • PVD and multi-layering realises extra toughness.

• Dramatically improving the heat and wear resistance!
• Excellent welding resistance due to low coefficient friction!

Wide Range of Inserts

• M2 Breaker - Economical molded inserts. Suitable for machining a wide range of work materials under various cutting conditions.
• G1 Breaker - High accuracy peripherally ground inserts. Large rake angle to provide high cutting edge sharpness. An HTi10 insert is available with a polished rake face to prevent welding problems when machining aluminum alloys

We are here to guide our clients with the secure payment procedures. With us, the customers get convenience to pay through both online and offline payment methods Our establishment in Vadodara(India) is well connected by varied modes of transport. Thus, we are capable of reaching patrons with ease.

 

Tough applications require ''Plus'' performance

• (Al, Ti, Cr)N multilayer coating (MS Plus)
  • Our original coating technology enables a multilayer of (Al, Ti)N and (Al, Cr)N. It allows machining of a wide range of workpiece materials.

• SQUARE END MILLS
• MPMHV/MPJHV
  • The irregular helix geometry reduces vibration to enable efficient machining of carbon and stainless components.

• CUTTING PERFORMANCE
  • Comparison of surface roughness
  • Good surface with no chattering due to irregular helix.

• Comparison of feed rate
  • Up to double the feed rate of conventional end mills.

Abiding by the stern delivery policies, we make certain that the product range is efficiently packed and delivered on time. We are strongly backed by a well maintained and managed storage house wherein we store our products for meeting urgent and massive requirements of the buyers.

 

Suitable for heavy cutting due to holder rigidity.
Feature

• Design Features of Dccc Type End Mill

Power Consumption

• Please use the chart below for reference, please select the conditions that suits the machines power.
• Chip Discharge Q (mm3/min.)=Table Feed x Depth of Cut x Cutting Width ÷ 1000

For Use of Apmx Long Type

• Since the overhang from the milling chuck is long, a large width of cut will cause chattering and tool breakage.
• Keep the width of cut small and the depth of cut in axial direction large. (See the following illustration.)
• For slot milling, keep the table feed at not more than half the value listed in the above table. (Use the APMX Short type as much as possible.)

We do not have to worry about stock-out situations and undertaking bulk orders, as are facilitated by a large storage facility. It has the latest inventory management software that helps us to maintain year around availability of the products. Ours is a well-established firm located in Vadodara(India) and engaged in the business of providing a wide assortment of quality products.