Our Products
The omni-directional movement of the Omni Wheel comes from its unique design. The combination of these two rolling elements provides a compact and inexpensive unit for moving heavy loads in any direction along a plane, doing so smoothly and with minimum effort.
Modularity and flexibility have been leading the design of Varvel products since 2000. This way, the gearbox kit concept was launched, allowing anyone to assemble the unit in few minutes.
Some kits are even common to all the gearbox series; i.e. motor flanges, motor elastic couplings.
The feature provides the highest flexibility to Varvels distributors and resellers who - thanks to a limited kit selection - are able to immediately configure the required product.
We are supplyingBox Series Worm Gear BoxesofM/s. Rotomotive Powerdrives India Ltd.which is anIndo-Italian joint ventureCompany.
The new patented BOX series of worm gear units is made with die-casting aluminium housing from size 25 up to 90, and in cast iron for the size 110. loads.
The housing has been designed with parametric three-dimensional CAD SW supported by programs of analysis of the thermal dissipation capacity and the structural resistance/deformation under the effect of working loads.
In order to increase silence, efficiency and duration, the wormshaft is made in case hardened steel and ground machined, while the worm wheel is in shell cast bronze. Before being assembled, the worm wheel is submitted to a running-in working period to improve the surface finishing and hardness.
From type 63 and up, 2 taper roller bearings are mounted on the wormshaft, improving the mechanical resistance to the axial loads given by the wormwheel. Moreover, the combination of this characteristic and 2 nilos (mounted on the unit sizes 75 up to 110 to keep lubrication grease inside the bearings even when they are not touched by the oil bath), permits the mounting of the whole BOX range, from the size 25 to the size 110, in the positions V5 and V6 without any need of additional interventions.
The gear unit is equipped with a full set of filler, level and breather plugs, permitting all mounting positions and facilitating the management of the stock.
A paint coat cancels the negative effects of the aluminium porosity and protects the housing from oxidation patented.
We are supplyingROBUS Inline Helical Gear BoxesofM/s. Rotomotive Powerdrives India Ltd.which is anIndo-Italian joint ventureCompany.
Use of high strength steels like 15CrMo4 and case hardening to 58 2 HRC reduce the wear rate in wheels. All wheels are profile ground to Din 3962 class 6 accuracy for low noise and high efficiency. | ||||||||
Shafts are made from 42CrMo4 steel and tempered to reach a hardness of 23-35 HRC, thus increasing their capacity to withstand shearing stresses.
|
Micro Controller PIC16F72 based digital PURE SINE WAVE Inverter / Home UPS kits (performance comparable to DSP design) are an excellent Micro controller kits to demonstrate the working of a power electronic system. The output waveform is pure sine wave and the system can have ratyed load of 600, 800, 1400VA.
The charging mechanism used is constant current-constant voltage. This will ensure better battery management. Overload and short circuit is provided both in firmware and hardware.
The output voltage is regulated within a range of 210-250 V. The kit runs on a 12V DC (600 & 800VA) and 24V DC (1400VA) bus and is designed to get high efficiency.
Micro Controller PIC16F72 based digital inverter/Home UPS kits are an excellent Micro controller kits to demonstrate the working of a power electronic system. The output waveform is modified square and the system can have rated load of 600, 800, 1400VA.
The charging mechanism used is constant current-constant voltage. This will ensure better battery management. Overload and short circuit is provided both in firmware and hardware. The output voltage is regulated within a range of 210-250 V. The kit runs on a 12V DC (600 & 800VA) and 24V DC (1400VA) bus and is designed to get high efficiency.
Axiom's Micro Controller PIC16F676 based digital Stablizer Control kits are an excellent Micro controller kits to demonstrate the working of a power electronic system. .
1- No need of 0.18V transformer 2- Setting stored for life time 3- No possibility for this problem. 4- Relay works smoothly. 5- High Cut Delay is present and no possibility of fault High cut. 6- Low Cut facility 7- 3mintus time delay and will remain same 8- LED indication on 2 LEDs for all modes 9- Audio indication for High cut 10- Single LT wiring is easy 11- Setting is based on single button |
We are supplyingAC Geared MootorsofM/s. Rotomotive Powerdrives India Ltd.which is anIndo-Italian joint ventureCompany.
We are supplying conveyor rollers made of high quality materials, with roller bearings, housings with special seals. High quality performance for modern materials handling
We are supplying high quality custom made Chain Sprockets made of high quality materials with zero errors.
The Ball Transfer Units are the latest development used in conveyer systems. Ball transfer units allow objects to be moved in any horizontal direction with minimum effort.