Bearing & Tool Centre - Micrometer

Features: diameter of measuring disk: 20mm.787""0.7mm.028"" (1mm: models over 100mm) edge thickness to enter narrow recesses.With ratchet stop for constant force.With a standard bar except for 25mm 0-1"" model.With spc output (series 323).The series 223is provided with a mechanical digit counter for quick reading of measurements.Supplied in fitted plastic case. (over 100mm models supplied with wooden cases) function: origin-set, zero-setting, data hold, data output, inchmm conversion (inchmm models) alarm: low voltgage, counting value composition error.

This range includes tube micrometers, blade micrometers, disc micrometers, point micrometers & spline micrometers.1) Tube type : [type - t1] spherical hardened steel anvil & flat carbide spindle face.[type - t2] both ends spherical hardened steel faces. 2) Disc type: rotating - hardened steel measuring faces.3) Disc type: non - rotating - hardened steel measuring facesNote:1) Certificate of calibration is supplied with each micrometer, traceable to n.P.L. Standards.2) prices for readings 0.001mm & 0.0001" on request 4) Point type : 15 hardened steel measuring tips.5) Point type : 30 hardened steel measuring tips.6) Spline type : 3 mm x l 8 mm carbide measuring faces.7) Spline type : 2 mm x l 5 mm carbide measuring faces8) Blade type : non-rotating-hardened steel measuring faces.

Point Micrometers - Series 342, 142, 112Series 342FeaturesIP65 waterdust protection (Series 342).Pointed spindle and anvil for measuring the web thickness of drills, small grooves, keyways, and other hard-to-reach dimensions.15 degree and 30 degree measuring pointsare available.The measuring points have approximately 0.3mm .012 radius.With Ratchet Stop for constant force.With SPC output (Series 342).With digit counter (Series 142).With a standard bar except 0 - 25mm and 0 - 1 model.Supplied in fitted plastic case. Technical DataAccuracy: Refer to the list of specifications. Resolution*: 0.001mm or .00005"0.001mmGraduation**: 0.01mm or .001"Display*: LCDBattery*: SR44 (1 pc.), 938882Battery life*: Approx. 1.2 years under normal useDustWater protection level*: IP65*Digital models **Analog modelsFunction of Digital Model Origin-set, Zero-setting, Data hold, inchmm conversion(inchmm models) Alarm: Low voltage, Counting value composition errorOptional Accessories for Digital Model05CZA662: SPC cable with data switch (1m40) 05CZA663: SPC cable with data switch (2m80)

For measurement of the pitch diameter of threadInterchangeable anvils depending on the screw shapeFor measurement of the pitch diameter of thread Fixed anvil

Digital Outside Micrometers - Series 193Series 193FeaturesMechanical digit counter with 0.01mm or .001" reading for quick and error-free readingWith a standard bar except for 0-25mm 0 -1 model. Technical DataAccuracy: Refer to the list of specifications.Counter reading: 0.01mm or .001"Graduation: 0.01mm, 0.001mm, .001" or .0001"Flatness: 0.6m .000024 Parallelism: (2 R100)m, R=max. range (mm) [.00008 .00004 (L4)], L= max. range (inch) Measuring faces: Carbide tipped-

Inside micrometers - series 345, 145-caliper typeseries 145featurescaliper type jaws are made of high-grade, tool steel.Locking clamp for positive locking of spindle.Satin-chrome finished.A special holder is available to be used with mitutoyo micrometer stand. Technical data accuracy: refer to the list of specifications.(excluding quantizing error for digital models) resolution*: 0.01mm or .00005"0.001mmgraduation**: 0.01mm or .001"measuring faces: carbide tippeddisplay*: lcdbattery*: sr44 (1 pc.), 938882battery life*: approx. 1.2 years under normal use*digital models **analog models function of digital model origin-set, zero-setting, data hold, data output, inchmm conversion (inchmm models) alarm: low voltage, counting value composition errorfunction lock2 presets

Features The new design of the MDC-S allows for simple operation. A larger LCD display allows the user to read all measurements with ease. The addition of the automatic power (ONOFF) function assures long-lasting battery life. Slim, lightweight construction for easy, one-handed operation as compared to a conventional digital micrometer.

Measure over-pin diameter of gearsResolution 0.001mm0.00005"IP54 dustwaterproofButton function: onoff, set, mminch, ABSINC, data outputData outputSR44 or LR44 battery, automatic power offRatchet stopSupplied with setting standards (except 0-25mm0-1")Optional accessary: ball tips (code 7391, next page), data output system

Resolution 0.001mm0.00005"IP54 dustwaterproofButton function: onoff, set, mminch, ABSINC, data outputData outputSR44 or LR44 battery, automatic power offRatchet stopSupplied with 7 pairs of anvilspindle tip(same as series 3280, previous page)Setting standards are included (except 0-25mm0-1")Optional accessary: anvilspindle tip code 3280-SP1 and 3280-SP2(same as series 3280, previous page), data output system

Measure hub thickness and shoulder inside a boreGraduation 0.01mmRatchet stopCarbide measuring facesSupplied with setting standards (except 0-25mm)

Measure pitch diameter of screw threadsResolution 0.001mm0.00005"Button function: onoff, set, mminch, ABSINC, data outputData outputSR44 or LR44 battery, automatic power offNon- rotating spindleRatchet stopSupplied with 60 setting standardsOptional accessary: 55 setting standards, measuring tips (code 7381, previous page), data output cable (code 7306-30, 7302-SPC2A, 7305-SPC3)

Measure over-pin diameter of gearsGraduation 0.01mmRatchet stopOptional accessary: ball tips (code 7391, next page)Supplied with setting standards (except 0-25mm)

Measure root tangent length of gearResolution 0.001mm0.00005"Non-rotating spindleButton function: onoff, set, mminch, ABSINC, data outputData outputSR44 or LR44 battery, automatic power offRatchet stopSupplied with setting standardsOptional accessory: data output system (code 7306-30, 7302-SPC2A, 7305-SPC3)

Holtest (Type II) Series 368-Three-Point Internal MicrometersSeries 368FeaturesThe Holtests (type II) have three contact points made of alloyed steel.Measurement can be taken closer to the bottom of the blind bore.Can measure deep holes using an Extension Rod (optional).With Ratchet Stop for constant force.Setting Rings for zero point adjustment are optional.Supplied in fitted plastic case up to 100mm 4. Over 100mm 4 supplied in wooden case. Technical Data Graduation: 0.005mm or .0002"Measuring method: Three-point methodContact point: Harden Steel

Tubular Inside Micrometers Series 137-Extension Rod Type, Series 139-Extension Pipe type, Series 140-Extension Pipe TypeSeries 137FeaturesWide range of ID measurements by combining extension rods (pipes) and anvils with the micrometer head.Carbide-tipped measuring faces are available. (series 137)The 139 and 140 series use highly-durable large-diameter extension pipes.Series 137 supplid in fitted plastic case except 1550mm60in come in wooden case.Series 139 supplied in fitted wooden case except 500mm20in come in plastic case.Series 140 supplied in fitted wooden case. Technical DataAccuracy: (.00012 .00005n (.00004R2))inGraduation: 0.01mm or .001"

Range:5-30 mm, 25-50 mm, Reading: 0.01mm, 0.01mm.quality product which is not what we put into it, but quality is what the customer gets out of our products.

Resolution 0.001mm0.00005"IP54 dustwaterproofButton function: onoff, set, mminch, ABSINC, data outputData outputSR44 or LR44 battery, automatic power offRatchet stopOptional accessory: data output system

Mitutoyo 115-215 Tube Micrometer 25-50mm 0.01mmMitutoyoProduct Code 115-215Tube MicrometerRange 0-25mmGraduation 0.01mm2 Spherical FaceTungsten Carbide Faces

Inside Micrometers - Series 345, 145-Caliper TypeSeries 145FeaturesCaliper type jaws are made of high-grade, tool steel.Locking clamp for positive locking of spindle.Satin-chrome finished.A special holder is available to be used with Mitutoyo Micrometer Stand. Technical Data Accuracy: Refer to the list of specifications.(excluding quantizing error for digital models) Resolution*: 0.01mm or .00005"0.001mmGraduation**: 0.01mm or .001"Measuring faces: Carbide tippedDisplay*: LCDBattery*: SR44 (1 pc.), 938882Battery life*: Approx. 1.2 years under normal use*Digital models **Analog models Function of Digital Model Origin-set, Zero-setting, Data hold, Data output, inchmm conversion (inchmm models) Alarm: Low voltage, Counting value composition errorFunction Lock2 Presets

Carbide tipped measuring faces parallel, ground and lapped.Stainless Steel spindle for rust prevention.A built-in Ratchet in the Thimble facilitates single-hand operation.Zero setting once done cannot be easily tampered with.Heat insulating grip plates cover the entire handling portion of the micrometer frame.Robust design withstands toughest workshop conditions.Sharp laser markings for better visibility & durability. Range & Readings: 0 to 2000 mm (Reading 0.01mm) 0 to 80" (Reading 0.001") 0 to 150 mm (Reading 0.001mm) 0 to 6" (Reading 0.0001")

We offer the Mitutoyo Screw Thread Micrometer, a precision instrument tailored for manufacturers, exporters, suppliers, retailers, and traders seeking top-quality measurement tools. With a range of 0-25mm, accuracy of +-4 micrometers, and resolution of 0.001mm, this micrometer ensures precise and reliable measurements. Featuring an LCD display, 8 months battery life under normal use, spindle feed error of 3 micrometers, and graduation of 0.01mm, it's a must-have for B2B buyers in need of superior metrology equipment.

FeaturesIP65 waterdust protection 340 series models with a range up to 12in300mm.Wide measuring range with interchangeable anvils.With a Ratchet Stop for constant force.Supplied with zero-setting standards bar for each range.With SPC output (Series 340).Supplied in fitted wooden case. Technical Data Accuracy: (4 R75)m, R=max. range (mm)[.00016 .00004 (L3)] L = Max Range (Inch) Resolution*: 0.001mm or .0001"0.001mm(340-351-10: .00005"0.001mm) Graduation**: 0.01mmFlatness: 0.6m.000024 for models up to 300mm12 1m.00004 for models over 300mm12 Parallelism: 2m.00008 for models up to 75mm3 3m.00012 for models up to 150mm6 (2 R100)m for models over 150mm, R=max. range (mm) [.00008 .00004 (L4)] L= Max range (inch) Measuring faces: Carbide tippedDisplay*: LCDBattery*: SR44 (1 pc.), 938882Battery life*: Approx. 1.2 years under normal useDustWater protection level*: IP65*Digital models **Analog models Function of Digital ModelZero-setting, Data hold, Preset, Data output, inchmmconversion (inchmm models) Alarm: Low voltage, Counting value composition error***Function Lock***2 Presets

Resolution 0.001mm0.00005IP54 dustwaterproofButtons: onoff, set, mminch, ABSINCData outputSR44 or LR44 battery, automatic power offRatchet stopOptional accessary: data output system, setting ring (code 6312)