Mumbai, Maharashtra, India
GST : 27AACFC7672E1ZG
Verified
Add Review
Our Products
Contact us to buy premium quality Duplex Steel Plates at nominal rates. The company has cemented its presence among the reliable Importers, Suppliers and Exporters of Duplex Steel Plates from Maharashtra. The Duplex Steel Plates we make available undergo rigorous quality checks before the final dispatch. Bulk orders of the Duplex Steel Plates are delivered by us within stipulated time. Buyers can purchase the Plates at market-leading rates. Available Grades
Forms of Duplex 2205 available with us
Duplex 2205 Applications
Corrosion ResistantThe duplex 2205 stainless steel serves as cost effective solution for the application where 300 grade steel is effected by chloride stress corrosion cracking. The steel is used where extremely corrosion resistant steel is required, this includes food processing applications, bleaching applications, marine environments, closed loop water systems and brackish water applications.
Chemical Composition, %
| Cr | Ni | Mo | C | N |
|---|---|---|---|---|
| 22.0-23.0 | 4.50-6.50 | 3.00-3.50 | .030 Max | 0.14-0.20 |
| Mn | Si | P | S | Fe |
|---|---|---|---|---|
| 2.00 Max | 1.00 Max | .030 Max | .020 Max | Balance |
Wear resistant steel is used in areas where there is likely to be a high degree of abrasion or wear of the steel plate. Typical applications are in truck beds, attachments to diggers and earth movers and in processing applications in the mining industry. The key quality for wear resistant steels is their hardness. We sell wear plate according to its hardness measured on the brinnell hardness test usually in 400hb and 500hb grades. If your specification is to the rockwell test we can also advise. Steels with a high hb rating (brinell hardness) are intended for applications where wear or abrasion resistance is important. The benefit of using an abrasion resistant steel is that that the plant, machinery or constructions working life can be extended considerably. This can significantly improve the reliability, durability and safety of structures and equipment. It also helps to reduce the maintenance costs associated with wear and breakdown of plant. 400 hb steel is over 3 times harder than mild steel (120hb), but only a third as hard as stainless steel (1250hb). Example uses are for construction machinery, skips, bulldozers and excavators, buckets and conveyors. The steel is quenched which provides wear resistance; in order to improve hardness it may also be tempered. Lower hbs generally provide good cold bending properties and good weldability. Weldability is not generally reduced as the hardness increases. Wear resistant steels are not appropriate for use at temperatures over 250c as the heat can cause changes to the material properties. Testing is undertaken by firing 10mm steel or tungsten carbide ball at 29kn and the size of the resulting indentation is measured. Tests are carried out according to en iso 6506 or astm e10. The figures below are representative of 15mm thick 400hb and 500hb plates. c max si max mn max p max s max cr max 400 hb 0.15% 0.70% 1.60% 0.225% 0.01% 0.50% 500 hb 0.29% 0.70% 1.60% 0.025% 0.01% 1.00% ni max mo max b max cev set 400 hb 0.15% 0.25% 0.004% 0.37% 0.27% 500 hb 0.50% 0.30% 0.004% 0.62% 0.41% values are typical and for general information purposes only. Yields for 400hb steel are in the region of 1100 mpa with tensile strengths of about 1250 mpa. Abrasion resistant hb 200400450500 wear-resistant steel. Has a hardness of approximately 200400450500 hb. It combines high wear resistance with toughness and good weldability. Brand name supplied by us are of tiscral sailhard jiscral las07 hardox dillidur durostat abraso xar and other well know brands as per following specification. Hardox-400, hardox-450, hardox-500, raex-400, raex-450, raex-500, hb-400 fora-400, fora-450, fora-500, abrazo-400, abrazo-450, abrazo-500, hb-450 nicrodur-400, nicrodur-450, nicrodur-500, brinar-400, brinar-450, brinar-500 dillidur-400v, dillidur-450v, dillidur-500v, ar-400, ar-450, ar-500, hb-500 s690 ql, maxil-690, naxtra-70, dillimax-690t, supralsim-690, weldox-700e sailhard, tiscral, jiscral, las07 wear resistant steel abrasion resistant steel 200bhn, 250bhn, 400bhn, 450bhn, 500bhn wear abrasion resistant steel 200hbw, 250hbw, 400hbw, 450hbw, 500hbw abrasion resistant wear steel armox-500, armox-500t, ramor-500, armour for ballistic protection armor high ballistic steel mil-a 46100 mil-a12560 armox 500t ramor 500 mil a-46100 mil a-12560 mil-a-46100 mil-a-12560 high ballistic steel armor
We offer ROCKSTAR Arcelor Mittal Nippon steel steel plates. Champak industries is agent of nssmc japan for there abrex 400 and 500 series (previously named as sumihard 400 and 500) is the wear plate series form nippon sumitomo steel metal corporation, japan.equal to hardox 400 and hardox 500 the use of abrasion resistance abrex steel plate markedly reduces the weight of structural members exposed to serve abrasive conditions. Compare with regular steel, abrex steel plate reduces structural weight and delivers economic merits. Adoption of high performance abrasion resistant abrex will prolong the service life of machinery and component. We maintain all the sizes and thickness of abrex sumihard 400 and 500 from 03mm 60mm thickness are ready and available in champak industries stockyard.
Additional Information:
Payment Terms : L/C
ROCKSTAR 500 Plates ROCKSTAR 500 Plate can easily be bended and welded. These plates are resistant to abrasion and is widely used in various applications that require higher wear resistance. Further, the plates are designed with a hardness of 500 HBW for applications where demands are imposed on abrasion resistance in combination with good cold bending properties. Our respected clients can also avail this range in various sizes and finishes as per their requirements. Corrosion Resistant Plate Features • Abrasion resistance • Welding ability • Wear resistant • High tensile strength Application • Buffer bins • Grizzly bars • Measuring bins and Skips Chemical Composition Plate C Si Mn P S Cr Ni Mo B CEV CET thickness mm max % max % max % max % max % max % max % max % max % typv typv 041313 0.27 0.7 1.6 0.025 0.01 1 0.25 0.25 0.004 0.49 0.34 (13)-32 0.29 0.7 1.6 0.025 0.01 1 0.5 0.3 0.004 0.62 0.41 (32)-40 0.29 0.7 1.6 0.025 0.01 1 1 0.6 0.004 0.64 0.43 (40)-80 0.3 0.7 1.6 0.025 0.01 1.5 1.5 0.6 0.004 0.74
Additional Information:
Payment Terms : L/C, T/T
Owing to its high tensile strength, the ROCKSTAR 400 Steel Plates are used for load bearing in many applications. We are an eminent Supplier, Importer and Exporter of ROCKSTAR 400 Steel Plates from Maharashtra. The Hardox 400 Steel Plates we make available features high durability, reliability, wear and tear resistance, abrasion resistance, etc. We are capable of delivering bulk orders of the ROCKSTAR 400 Steel Plates. Features
Application
Chemical Composition
| Plate | C | Si | Mn | P | S | Cr | Ni | Mo | B | CEV | CET |
|---|---|---|---|---|---|---|---|---|---|---|---|
| thickness mm | max % | max % | max % | max % | max % | max % | max % | max % | max % | typv | typv |
| 3-(8) | 0.15 | 0.7 | 1.6 | 0.025 | 0.01 | 0.3 | 0.25 | 0.25 | 0.004 | 0.33 | 0.23 |
| 08/20/13 | 0.15 | 0.7 | 1.6 | 0.025 | 0.01 | 0.5 | 0.25 | 0.25 | 0.004 | 0.37 | 0.27 |
| (20)-32 | 0.18 | 0.7 | 1.6 | 0.025 | 0.01 | 1 | 0.25 | 0.25 | 0.004 | 0.48 | 0.29 |
| (32)-45 | 0.22 | 0.7 | 1.6 | 0.025 | 0.01 | 1.4 | 0.5 | 0.6 | 0.004 | 0.57 | 0.31 |
| (45)-51 | 0.22 | 0.7 | 1.6 | 0.025 | 0.01 | 1.4 | 0.5 | 0.6 | 0.004 | 0.57 | 0.38 |
| (51)-80 | 0.27 | 0.7 | 1.6 | 0.025 | 0.01 | 1.4 | 1 | 0.6 | 0.004 | 0.65 | 0.41 |
| (80)-130 | 0.32 | 0.7 | 1.6 | 0.025 | 0.01 | 1.4 | 1.5 | 0.6 | 0.004 | 0.73 |
Armor & ballistic metal plate is designed for a huge type of navy specifications and structural makes use of that require armor steel plate authorized by all us departments and groups for fight and protection applications.
Armor & ballistic metallic plate may be utilized in the manufacture of military cars, structural housings with excessive protection, armaments and different protective systems and sundry applications.
From one plate order to multi-megaton contracts, Champak Industries is your first-class useful resource for armor & ballistic metal plate. We presently supply to a wide variety of OEMS and part fabricators and are equipped to serve you.
Range :
Weathering steel (Corrossion Resistant Plate), fine-recognised beneath the trademark corten a metal and once in a while written without the hyphen as "corten a steel", is a group of metal alloys which had been advanced to obviate the want for painting, and form a stable rust-like appearance if exposed to the weather for numerous years. united states steel company (uss) holds the registered trademark on the call corten a. even though usasold its discrete plate commercial enterprise to international metallic institution (now arcelor-mittal) in 2003, it still sells corten a branded material in strip-mill plate and sheet forms.
The unique corten a acquired the same old designation ASTM a 242 type-1("cor-ten a") from the ASTM global standards institution. More recent ASTM grades are a 588 ("corten a") and a 606 for thin sheet. All alloys are in not unusual manufacturing and use.
JIS G 3125:2004: eastern grade for climate resistant metallic plates: superior atmospheric corrosion resisting rolled steels this widespread specifies the rolled steel having excessive atmospheric corrosion resistance, for use for vehicle, constructing, metallic tower and other shape.
IRSM 41-97 corrosion resistance steel Indian grade for weather resistant metallic plates: IRSM 41-97 general of Indian railways especially formed for wagon frame because of it high resistance to corrosion, main wagon builder being rail train manufacturing facility.
Applications :
Range : Corten Plates.
Chemical Composition
| C | Si | Mn | P | S | Cr | Cu | Ni |
|---|---|---|---|---|---|---|---|
| ≤ 12 | 0.25 - 0.75 | 0.20 - 0.50 | 0.07 - 0.15 | ≤ 0.030 | 0.50 - 1.25 | 25 - 0.55 | = 0.65 |
Mechanical Properties : Hot Rolled Sheets
| Yield Strength (MPa) |
Tensile Strength (MPa) |
Minimum Elongation A (Lo = 5.65 vSo) % |
|---|---|---|
| 355 | 470 - 630 | 20 |
Mechanical Properties : Cold Rolled Sheets = 3 Mm In Thickness
| Yield Strength (MPa) |
Tensile Strength (MPa) |
Minimum Elongation A % |
|---|---|---|
| 275 | 410 | 25 |
Champak Industries has large stocks of high tensile steel, sometimes known as High Strength steel, in a variety of grades. We focus on steel plates and specifically high tensile steel plates greater than 40 mm thick. For many customers a steel plate with a yield strength of 355 MPa or higher is considered to be high tensile steel and we have many tens of thousands of tones of these plates in stock. For the S355 and S460 MPa level we have plates to EN10025-2, EN10025-3, and EN10025-4. You can find more details on these under the structural steel section. For steels with a higher tensile strength to EN10025-6 we carry S690QL, S690QL1, S890QL, S960QL and the ultra-high tensile steel S1100QL. These steel plates are all from Dillinger Hutte, the world's leading heavy plate mill and are certified to EN10204 3.2. We don't stock any high tensile steel plates to ASTM standards though many of our plates will be suitable as an equivalent.
High Tensile Steel Plates Ex-stock :
High Tensile steel plates are available from stock in thicknesses up to 250 mm and our focus is to provide multiple plate options at every thickness to customers. We don't just keep a couple of token thick plates and hope to buy additional plates when required from other stockholders. We specialise in carrying a large stock of all our plates so that we can deliver large quantities of high tensile plates immediately from our own stock. There are three key reasons to buy high tensile steel plates from Oakley Steel.
Range :
Champak Industries is a large stock of shipbuilding steel plate. This is normally used for shipbuilding and offshore use. We keen on supporting customers' requirements of thicker and higher quality plates especially when through thickness testing is important.
Mainly our steel plates for shipbuilding are approved by either Lloyds Register of Shipping (LRS) or Det Norske Veritas (DNV).
We can also support customers who require shipbuilding plates to ABS though this comes as an additional report to the MTC.
Shipbuilding Steel Plate Ex-Stock :
We focus on high performance EH36 and DH36 plates with the thickest plates being to Lloyds Register. Typically for most customers we are able to supply a significant number of 100mm plus plates from our stock and this can be collected almost immediately (subject to PO approval and plate movements inside the warehouse).
Who buys shipbuilding steel plate from us? :We mainly deliver heavy engineering groups serving the oil and fuel and offshore sectors in Asia. They commonly require thick plates of excessive pleasant. There are regularly very rigorous necessities round both minimal yield strength and the chemical composition.
We're famous with both nearby stockholders and engineering groups each due to the fact we've got excessive quality AH36, DH36 and EH36 plates in inventory, and because the choice of plates that we have available permits engineers to select plates that meet their requirements in preference to having to are searching for derogations or non-compliances.
Thick Steel plates for shipbuilding :Like maximum of our metal stockholding our shipbuilding plates are typically thick and heavy. While we do have great stocks of 6mm – 40mm plates we are specific in our so much of our inventory is above 50mm thick, and mainly how a whole lot is above 100 mm thick.
Many stockholders don't deliver heavy plates, forcing customers to buy from the mill and receive longer lead times. We stock thick plates for several motives. The important thing one is that we have confidence inside the technical first-class of the metal plate.
Dillinger is the oldest heavy plate mill in the global and has a large quantity of enjoy in producing thick plates where the yield strength is maintained to lots big quantity as the plate gets thicker, at the same time as additionally avoiding the troubles with negative micro-shape and tearing and laminations that can affect different metal producers and rollers.
That is of essential importance to many shipbuilders. Believe discovering that considered one of your key base plates has a lamellar tear in it – and you want to cast off greater than one thousand MT from your new construct shape a good way to get right of entry to and replace the plate. The best of Dillinger plate reduces that threat.
Fine Steel Plates For Shipbuilding :You may usually purchase cheaper metal. Apparently you could even buy steel plates with a fake MTC. If that is what you want then that's a unique marketplace to the only we aid.
Whether you need 10 mm or 100 mm thick metal plate there are some key questions that you have to answer. Does the metal meet the specification? Does the metal deliver sufficient margin for my design. The steels that we stock for shipbuilding are all designed to reap the specification that they are able to regularly be used at a better grade. For example our dh36 plates are generally examined to -40 on a in step with warmness foundation. that means that while they don't have the assured values that eh36 has – there are lots of dh36 plates in inventory that meet the necessities for eh36.
That level of satisfactory way that your production manner is accelerated. Procurement is less complicated due to the fact its miles clean that the plates meet the necessities. Internalqa becomes trustworthy with far fewer troubles of plate great to devour time, and final approval by the purchaser gives them confidence. Faster, simpler, easier production of the layout.
And of route with higher exceptional the disorder and rejection charge is decreased. Those shipbuilding metal grades are usually to be had ex-stock. Thethickness is for indication most effective however we are able to normally have thicker plates to be had in most grades.
Range :
Technical Specifications
| Standard | Grade | Minimum Thickness (mm) | Maximum Thickness (mm) |
|---|---|---|---|
| Lloyds Register | Grade A | 5 | 150 |
| Lloyds Register | AH36 | 5 | 150 |
| Lloyds Register | DH36 | 5 | 150 |
| Lloyds Register | EH36 | 5 | 150 |
We are the noted Exporter, Importer and Supplier of a wide variety of Corten Steel Plates. We offer Corten Steel Plates in different ranges that include Corten Steel Plate, Corten A Steel Plates, Corten B Steel Plates, Corten Steel IRSM 41 Grade & Corten Steel Grade A588. Corten Steel Plates are widely appreciated for their high strength, durability, corrosion resistance, and dimensional accuracy. Furthermore, these plates are thermostatically balanced and are resistant to bad weather. These plates are widely used in bridge construction, structures, fences, urban furniture, sculptures and industrial containers. Standard Sizes :
1.2 mm, 50 mm
1.25m, 1.5m, 2.5m
up to 12 m
Chemical Composition
| According To EN 10027-1 & CR 10260 | C % max. | Si % max. | Mn % | P % | S % max. | N % max. | Cr % | Cu % | V% | Ni% | Z% | Mo% |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S235J2W | 0.13 | 0.4 | 0.20-0.60 | 0.04 | 0.03 | - | 0.40-0.80 | 0.25-0.55 | - | 0.65 | - | - |
| S355J0W | 0.12 | 0.75 | 1 | 0.06-0.15 | 0.04 | 0.01 | 0.30-1.25 | 0.25-0.55 | - | 0.65 | - | - |
| S355J2WP | 0.12 | 0.75 | 1 | 0.06-0.15 | 0.03 | - | 0.30-1.25 | 0.25-0.55 | - | 0.65 | - | - |
| S355J0W | 0.16 | 0.5 | 0.50-1.50 | 0.04 | 0.04 | 0.01 | 0.40-0.80 | 0.25-0.55 | - | 0.65 | 0.15 | 0.3 |
| S355J2W | 0.16 | 0.5 | 0.50-1.50 | 0.03 | 0.03 | - | 0.40-0.80 | 0.25-0.55 | - | 0.65 | 0.15 | 0.3 |
| S355K2W | 0.16 | 0.5 | 0.50-1.50 | 0.03 | 0.03 | - | 0.40-0.80 | 0.25-0.55 | - | 0.65 | 0.15 | 0.3 |
| According To ASTM & ASME Specn. | ||||||||||||
| A 588 Gr. A | 0.19 | 0.3- 0.65 | 0.80-1.25 | 0.04 | 0.05 | - | 0.40-0.65 | 0.25-0.40 | 0.02- 0.10 | |||
| A 588 Gr. B | 0.2 | 0.15- 0.50 | 0.75-1.35 | 0.04 | 0.05 | - | 0.40-0.70 | 0.20-0.40 | 0.01- 0.10 | |||
| A 588 Gr. C | 0.15 | 0.15- 0.40 | 0.80-1.35 | 0.04 | 0.05 | - | 0.30-0.50 | 0.20-0.50 | 0.01- 0.10 | |||
| A 588 Gr. K | 0.17 | 0.25- 0.50 | 0.50-1.20 | 0.04 | 0.05 | - | 0.40-0.70 | 0.30-0.50 | - | Cb-0.005 -0.05 | ||
| A 242 Type-1 | 0.15 | - | 1 | 0.15 | 0.05 | 0.20 min. | ||||||
| A 242 Type-2 | 0.20 | - | 1.50 | 0.04 | 0.05 | 0.20 min. | ||||||
| According To IS STD. | ||||||||||||
| IRSM-41 | 0.1 | 0.30- 0.50 | 0.25-0.45 | 0.075-0.14 | 0.03 | - | 0.35-0.49 | 0.30-0.60 | 0.05 | 0.28- 0.49 | - | 0 |
we stock below grade alloy steel chrome moly steel plate Sa 387 Gr 5 CL1 and Sa 387 Gr 5 CL2 Sa 387 Gr 9 CL1 and Sa 387 Gr 9 CL2 Sa 387 Gr 11 CL1 and Sa 387 Gr 11 CL2 Sa 387 Gr 12 CL1 and Sa 387 Gr 12 CL2 Sa 387 Gr 22 CL1 and Sa 387 Gr 22 CL2 Sa 387 Gr 91 CL1 and Sa 387 Gr 91 CL2 It is a chromium molybdenum alloyed steel plate mainly used for elevated temperature applications
Customers are seeking extreme protection and safety performance for their end-products. Ramor plate has excellent ballistic properties in combination with high hardness and strength. Ramor is developed for applications, where blast protection or high ballistic resistance is required.
Applications :
Ramor armour steels are manufactured with a novel direct quenching process. With this method not only a good blast and ballistic protection is achieved, but also good flatness, surface quality and dimensional accuracy are obtained. Ramor 400 steel is designed to give protection against high pressures caused by explosions and blasts. Ramor 500 is the most suitable choice, when protection is needed against kinetic energy projectiles i.e. ballistic performance. The number of the designation indicates the average Brinell hardness value 400 and 500 HBW, respectively.
Tolerances Heavy plates :
Cut lengths :
Surface condition :
General technical delivery condition :
Mechanical properties :The plate must take appropriate precautions to protect themselves and no outsiders must be allowed in the area. The safest location is usually by the bending ma- chine. The handling instructions of the steel supplier and safety instructions of the workshop must be adhered to in detail. New employees must receive appropriate train- ing before they are allowed to process hardened steels.
Materials testing :Recommended minimum plate thickness of Ramor 500
Heat treatment :Heat treatment is not recommended. If tempering process is needed, please, contact technical customer service for further assistance.
Welding :Ramor steels can be welded with common welding methods. Austenitic steel welding consumables are rec- ommended. Ferritic welding consumables can be used also, if the strength of the joint is important. If ferritic consumables are used, the need for elevated working temperature has to be studied in order to achieve fault- less weld joint.
Bending :When cold forming Ramor 500 steels by bending, the minimum bending radius of the upper tool has to be 8 times the thickness of the material. The correspond- ing bending radius for Ramor 400 has to be 5 times the thickness of the material. Special care has to be taken to the working safety, when these steels are cold formed. Mechanical cutting is not suitable as an edge preparation process for bended parts.
Cutting :Ramor steels are well suitable for laser and plasma cut- ting. Mechanical cutting can also be used, if the cutting shears/blades are hard enough and the equipment used is rigid. However, water jet cutting is preferred, because with this method the ballistic properties of the cut edge can be obtained.
Machining :Ramor steels can be machined using rigid hard metal tools and rigid equipment. Sufficient lubrication has to be provided and special attention has to be paid to clamping of work piece. The cutting parameters should be chosen in the way that the vibration of the cutting tool and the work piece can be avoided, because vibration decreases the lifetime of the cutting tool considerably.
Occupational safety :Special care must be taken in all stages of handling of hardened steels. Flanging is challenging due to the high strength and high flexural stresses of the plate. If the bending radius, for example, is too small and a crack is created in the bending point, the plate may fly from the bending tool in the direction of the bend.
Ramor. Heavy Plates And Sheets. Thickness Tolerances
| Heavy plates Thickness mm | Upper tolerance mm | Sheets Thickness mm | Upper tolerance, width-wise mm | |
|---|---|---|---|---|
| - | - | - | -1200 | 1201 – 1500 |
| 6.00 – 6.99 | 0.74 | 2.50 – 3.00 | 0.3 | 0.32 |
| 7.00 – 7.99 | 0.76 | 3.01 – 4.00 | 0.32 | 0.36 |
| 8.00 – 9.99 | 0.80 | 4.01 – 5.00 | 0.36 | 0.4 |
| 10.00 – 11.99 | 0.90 | 5.01 – 6.00 | 0.4 | 0.42 |
| 12.00 – 14.99 | 1.00 | 6.01 – 6.50 | 0.44 | 0.44 |
| 15.00 – 19.99 | 1.10 | - | - | - |
| 20.00 – 24.99 | 1.20 | - | - | - |
| 25.00 – 29.99 | 1.30 | - | - | - |
| 30 | 1.4 | - | - | - |
Note : Lower thickness tolerance for both plates and sheets is 0 mm.
Chemical Composition
Content %, maximum (cast analysis)
| - | C | Si | Mn | P | S | Cr | Ni | Mo | B |
|---|---|---|---|---|---|---|---|---|---|
| Ramor 400 | 0.24 | 0.7 | 1.5 | 0.02 | 0.02 | 1 | 1 | 0.7 | 0.01 |
| Ramor 500 | 0.32 | 0.7 | 1.5 | 0.02 | 0.02 | 1 | 2 | 0.7 | 0.01 |
Note : The steel is aluminium-killed and grain-refined.
Mechanical Properties, Typical
| - | R MPa | R MPa | A % | HB t°C Cha | ||
|---|---|---|---|---|---|---|
| Ramor 400 | 1100 | 1300 | 8 | 360 – 450 | -40 | 20 |
| Ramor 500 | 1450 | 1700 | 7 | 480 – 560 | -40 | 20 |
The typical impact strength values are results of the Charpy V impact tests in accordance with EN 10045-1. The value 20 J means tests carried out with 10 x 10 standard test pieces. When testing thicknesses less than 10 mm, the width of the test pieces corresponds with the plate thickness and the impact strength values decrease in direct relation to the surface area of the test piece.
Designed for severe wear and tear conditions, our High Manganese Steel Plates are non-magnetic. Our company is a reputed Supplier, Importer and Exporter of High Manganese Steel Plates from Maharashtra. It is annealed non-magnetic work-hardening Steel Plate, which offers an extremely high level of wear resistance when subjected to work. We are capable of delivering bulk orders of the High Manganese Steel Plates within stipulated time. Composition
Features
Application
Abrasion resistant (AR) steel plate is typically made in the as-rolled situation. These kinds/grades of steel plate merchandise have been evolved specially for long service lifestyles in harsh situations. Abrasion Resistant Plates products are suitable for a variety of programs in areas along with mining/quarrying, conveyors, cloth managing and construction, and earthmoving. Designers and plant operators pick AR plate steel when striving to extend service life of critical components, and reduce the weight of each unit put into service. The benefits of employing wear-resistant plate steel in applications involving impact and/or sliding contact with abrasive material are immense.
Steel plate for use in abrasive situations isn't regular as it isn't always governed through any ASTM code or spec. many steel plate producers produce their own brand of abrasion resistant steel and those are usually outstanding through an emblem call observed by means of the hardness of the metal which is measured in brinell gadgets.
Range :Hardox® Plates, Wear Resistant Plates, Hardox® 400 Plates, Hardox® 450 Plates, Hardox® 500 Plates, AR 400 Plates, AR 450 Plates, AR 500 Plates, Raex 400 Plates, Raex 450 Plates, Raex 500 Plates, HB 400 Plates, HB 450 Plates, HB 500 Plates, Fora 400 Plates, Fora 450 Plates, Fora 500 Plates, Abrazo 400 Plates, Abrazo 450 Plates, Abrazo 500 Plates, Nicrodur 400 Plates, Nicrodur 450 Plates, Nicrodur 500 Plates, Brinar 400 Plates, Brinar 450 Plates, Brinar 500 Plates, Dillidur 400V Plates, Dillidur 450V Plates, Dillidur 500VAR Plates, 400BHN Plates, 450BHN Plates, 500BHN Plates, Quard 400 Plates, Quard 450 Plates, Quard 500 Plates, Rockstar 400 (Essar, India Make), Rockstar 450 (Essar, India Make), Rockstar 500 (Essar, India Make), Abrex 400 (NSSMC, Japan Make), Abrex 450 (NSSMC, Japan Make), Abrex 500 (NSSMC, Japan Make), JFE EH 400 (JFE, Japan Make), JFE EH 500 (JFE Japan Make).
Our Hadfield Manganese Steel Plates are highly accredited for their work hardening properties. These plates are resistant to high-impact wear and scratch abrasion. Our Hadfield Manganese Steel Plates enhances five times the hardness of mild steel and three times the hardness of annealed stainless steel. Hadfield Manganese Steel Plates that we offer are widely applied in quarries and constructions, mines, iron industry and foundry, concrete and brick works, scraps, automotive industries, etc. Technical Specifications :
Features :
Application :
Standards
| EURONORM | 1.3401 X120Mn13 | DIN | W1.3401 |
|---|---|---|---|
| AFNOR | X120Mn13 | ASTM | A128 Gr B2 |
Chemical Analysis Typical Values (% Weight)
| C | Si | Mn | Mn | P |
|---|---|---|---|---|
| 1.13 | 0.4 | 13 | 0 | ≤ 0.20 |
Mechanical Properties
| Hardness HB | Yield Strength MPa | UTS MPa | El% | KCV 20 -C (68 - F) - J | |
|---|---|---|---|---|---|
| Typical Values | 220 | 380(55 KSI) | 940(136 KSI) | 40 | ≥ 112 J(≥ 83 ft.lbs) |
| Guaranteed Values* | 180/245 | 350(51 KSI) | 800(116 KSI) | 30 | 64 J(47 ft.lbs) |
* After water quenching 980 - C (1800 - F)
Physical Properties
| Density * | Expansion Coeff. 0-600 C | Specific Heat | Electrical * Resistivity | Thermal * Conductivity | Magnetic * Permeability | |
|---|---|---|---|---|---|---|
| Metric US | 7.88 | 10 -6-C1 21.5 10 -60 -F-1 19.9 | J/Metric Kg. C 502 BTU/lb/F .12 | O.m 75 O.m 75 | W/m. C 13 BTU/hr.-F 7.3 | ½1.002 |
We export, import and supply excellent quality Wear Resistant Steel Plates that are widely used in areas in which there is a high degree of abrasion or wear of the steel. Our abrasion resistant Wear Resistant Steel Plates help in reducing the maintenance cost connected with wear and breakdown of any plant. Wear Resistant Steel Plates that we offer are widely used in mechanical engineering applications, automotive industry, heavy lifting equipment, transportation industry, mining industries, etc. Our Wear Resistant Steel Plates are appreciated for excellent weldability and high hardness.
Details
| Chemical Composition | Mechanical Properties | HARDNESS-200 BHN (Min) | |||||
|---|---|---|---|---|---|---|---|
| GRADE | C % Max | Min % Max | P % Max | S% Max | SI % Ma | CE+ | HARDNESS-200 BHN (Avg).SAIL HARD | TISCRAL | 200 bhn steel plate. |
| SAILHARD | 0.23 | 1.6 | 0.05 | 0.05 | 0.5 | ||
| AI0.10 max, Cr 0.65 max, Nb +V+Ti0.15 Max | |||||||
The EN19 Grade Steel Plate that we offer exactly matches the desirable plates of such kinds. It is of the best quality and endowed with high tensile strength. We are working in full throttle to make it available to the length and breadth of the country and abroad. We are one of the eminent Exporters and Suppliers of EN19 Grade Steel Plate from Mumbai, India. Applications :EN19T was originally introduced for the use in the machine tool and motor industries for gears, pinions, shafts, spindles and the like. Later its applications became much more extended and it is now widely used in areas such as the oil and gas industries. EN19T is suitable for applications such as gears, bolts, studs and a wide variety of applications where a good quality high tensile steel grade is suited. Forging : Pre heat carefully, then raise temperature to 850-1200oC for forging. Do not forge below 850oC. After forging cool slowly in still air. Annealing : Heat the EN19T slowly to 680-700oC. Cool in air. Hardening : This steel grade is commonly supplied ready heat treated. If further heat treatment is required annealed EN19 should be heated slowly to 860-890oC and after adequate soaking at this temperature quench in oil. Temper as soon as tools reach room temperature. Tempering : Heat carefully to a suitable temperature selected by reference to a tempering chart or table. Soak at the temperature for 2 hours per 25mm of ruling section, then allow to cool in air. Tempering between 250-375oC is not advised as tempering within this range will reduce the impact value. Heat Treatment : Heat treatment temperatures, including rate of heating, cooling and soaking times will vary due to factors such as the shape and size of each steel component. Other considerations during the heat treatment process include the type of furnace, quenching medium and work piece transfer facilities. Please consult your heat treatment provider for full guidance on heat treatment of EN19T alloy steel.
Equivalent Grades
|
Internal Standard |
BS |
Din |
IS |
EN |
Saf/Aisi |
|---|---|---|---|---|---|
|
En 19 |
709M40 |
42CrMo2 |
40Cr4Mo3 |
EN19 |
4140, 412 |
EN19 is a high quality, high tensile steel usually supplied readily machine able in ‘T’ condition, giving good ductility and shock resisting properties combined with resistance to wear.
Chemical Composition
| Element | Min | Max |
|---|---|---|
| Carbon, C | 0.35 | 0.45% |
| Manganese, Mn | 0.5 | 0.80% |
| Silicon, Si | 0.1 | 0.35% |
| Nickel, Ni | ----- | ----- |
| Molybdenum, Mo | 0.2 | 0.40% |
| Chromium,Cr | 0.9 | 1.50% |
| Sulfur, S | ----- | 0.05 |
| Phosphorous, P | ----- | 0.05 |
Mechanical Properties
| Heat Treatment | Tensile Strength Rm N/mm² | Yield Stress Re N/mm² | a% on 5.665ÖSo | Impact Izod J | Impact KCV J | Proof Stress rp0.2 | Hardness HB | Size mm |
|---|---|---|---|---|---|---|---|---|
| R | 700/850 | 495 | 15 | 34 | 28 | 480 | 201/225 | >100≤250 |
| S | 775/925 | 555 | 13 | 27 | 22 | 540 | 223/277 | >150≤250 |
| S | 775/925 | 585 | 15 | 54 | 50 | 570 | 223/277 | >63≤150 |
| T | 850/1000 | 680 | 13 | 54 | 50 | 655 | 248/302 | >29≤100 |
| U | 925/1075 | 755 | 12 | 47 | 42 | 740 | 269/331 | >13≤63 |
| V | 1000/1150 | 850 | 12 | 47 | 42 | 835 | 293/352 | >6≤29 |
| W | 1075/1225 | 940 | 12 | 40 | 35 | 925 | 311/375 | >6≤19 |
Chrome Molybdenum steel plate (often referred to in the industry as Chrome Moly) is used for a wide variety of applications particularly in the oil and gas industry, the nuclear industry and fossil fuel power stations. The molybdenum provides increased strength and higher working temperatures whilst the chromium facilitates excellent corrosion resistance and oxidation.
With such high temperature tensile strength and anti-corrosive properties, our chrome molybdenum is also highly effective in salt water applications.
Chemical Composition (heat Analysis, %)
| C | Si | Mn | P | S | Cr | Mo | B |
|---|---|---|---|---|---|---|---|
| ≤ 20 | ≤ 0. 80 | ≤ 1.50 | ≤ 0. 025 | ≤ 0. 010 | ≤ 1.00 | ≤ 0. 50 | ≤ 0. 005 |
| The steel has a fine-grained microstructure. Nitrogen is absorbed to form nitrides by means of Al and, where applicable, Nb or Ti. Delivery Condition : Quenched or quenched and tempered (see ‘Heat Treatment’). Hardness at Room Temperature : In the delivery condition - 360-440 HB The Brinell hardness shall be determined in accordance with ISO 6506. | |||||||
Properties Typical Of 15mm Plate Thickness
| Carbon equivalent CET (%) [CET=C+(Mn+Mo) /10+(Cr+Cu)/20+Ni/40]: | 0.27 |
|---|---|
| Carbon equivalent CE (%) [CE=C+Mn/6+(Cr+Mo+V) /5+(Ni+Cu) /15]; | 0.42 |
| Yield strength (MPa) *) | 1050 |
| Tensile strength (MPa) : | 1250 |
| Elongation at fracture A (%) : | 12 |
| Bend radius for bending test on transverse test pieces | |
| (t=test piece thickness; bend angle: 180o) | ≥ 10xt |
| Notch-bar impact energy at -40oC | |
| on Charpy V-longitudinal test specimens (J) | 30 |
| *) 1 MPa = 1 N/mm2 | |
| Number of Tests Unless otherwise agreed upon in the order, the Brinell hardness shall be determined from each heat. The hardness shall be measured roughly 1mm below the surface. General Processing Information Prior to any processing, it is advisable to make use of the information available from the steel producer in order to draw on that experience for the processing. The following information can deal with only a few essential points. The recommendations given in STAHL-EISEN-Werkstoffblatt 088 (Weldable fine-grained structural steels, guidelines for processing, in particular for welding) correspondingly apply to this steel as well. Recommendations for welding are also given in EN 1011 part 1 and part 2 – Welding, Recommendation for welding of metallic materials-. It is left to the discretion of the processor/fabricator to decide which of the familiar precautions must be adopted to avoid cracking during thermal cutting and welding under the prevailing construction and fabrication conditions. Cold Forming The products made of this steel are suitable for cold bending provided, that consideration is given to the high hardness. The formability of steel decreases with increasing hardness. This has to be kept in mind when forming. The forming must take place at a slow and steady rate, the cut edges must be deburred and the plates heated, if necessary, prior to forming. A final stress-relieving is not necessary for this steel. Machinability In spite of its high wear resistance, the steel exhibits good machinability if sufficiently heavy machine-tools and sharp carbide-tipped tools are used. The feed rate and cutting speed have to be adjusted to the high hardness of the material. Heat Treatment Plates made of XAR®400 grade receive the required properties as a result of austenitizing and follow-on quenching in special facilities and, where applicable, tempering below Ac1. Direct quenching after hot-rolling is considered equivalent to conventional quenching. The heat treatment depends on the chemical composition and the product thickness. To avoid hardness losses, the steel must not be heated above 250°C. Thermal Cutting Preferably the flame-cutting process is used. For small product thicknesses, however, the plasma cutting process is used in the interest of minimum distortion. Preheating is not normally necessary when flame-cutting thicknesses up to around 30mm. However, if the workpiece temperature is below +5oC, or the cut edges are to be cold-formed in the course of further processing, preheating to about 150oC should be considered in the interest of cold cracking resistance. Welding If due consideration is given to the general rules for welding, this steel is weldable both manually and automatically. To prevent cold cracking in the welded joints only welding consumables giving welds of very low hydrogen content should be used. Preheating is not generally necessary for welding with austenitic filler metals. Preheating may be necessary for welding with ferritic filler metals. The preheat temperature level for welding depends on the plate thickness and the residual stress state of the structure. The working temperature should not go beyond 250oC. The wear resistance of components fabricated of XAR®400 may be increased with the aid of wear resistant layers deposited by means if welding or metal spraying. General Information Unless otherwise agreed in the order, the delivery will be governed by the conditions outlined in EN 10021. The admissible tolerances are based on EN 10051 for plates cut from hot strip and EN 10029 for four-high mill plates, unless other terms have been agreed upon. The plates will be supplied with a maximum flatness tolerance according to EN 10029, table 4, steel type H. Smaller flatness tolerances can be agreed upon at the time of ordering. For surface quality requirements EN 10163 is applicable. As per special agreement it is possible to supply plates descaled or descaled and prime | |
Such steel is generally used in applications where resistance to increased temperatures is critical. The steel is hard wearing and offers a resistance to large variations in temperature. Industrial applications include furnaces, heat exchanges and incinerators where temperatures can reach in excess of 1100°C.
Characteristics include corrosive resistance, creep resistance, oxidation resistance and hydrogen brittleness - all under extremely high temperatures. Our steels are made from nickel and titanium based alloys for outstanding high temperature performance.
The range offered by us includes plate, sheet, bar, pipe, tube and fittings. Standard and non standard sizes are available from stock, items outside of current stock can be produced rolled to size (utilising allocated rolling programmes).
Carbon steel plates which are tested to assess the susceptibility of the material to hydrogen induced cracking, which is a problem commonly found in wet H2S/sour service working environments.
HIC resistant steel is manufactured via the electric arc furnace with desulphurisation, dephosphorisation, ladle refining and vacuum degassing to provide an ultra clean and homogeneous steel. HIC steel is particularly suited for pressure equipment where wet H2S corrosion can be a problem.
We supply a wide range of hot rolled steel plate to various market places worldwide. Primarily serving the Petrochemical, Chemical, Oil and Gas, Construction and Shipbuilding industries.
Stock materials are ordered with additional stringent restrictions applied to the chemical, mechanical and testing requirements. This ensures that where clients have more complex requirements we are able to comply using ex stock material.
