Our Products
TheSPAN Decking Systemis designed to support a variety of bay sizes with amaximum load of 40 kNon any supporting leg . For maximum economy, the rapid strike drophead offers the facility for early striking of thedecking system. When the support plate on the drophead remains in position to support the slab, thedecking beamcan be dismantled and reassembled elsewhere to enable greater utilization of the equipment. This Decking system is ideally suited for construction of reinforced concrete suspended slabs, withplywood shuttering, and incorporates the benefitsof early striking. Large grid sizes of up to2.5 x 1.8 m ensures speedy erection and different sizesof primary and secondary beams can give a range of twelve support modules. Notching of plywood over the dropheads is eliminated, and standard sizes of plywood can be used.
Lock Standard verticalsare manufactured from48.3mm O.D. Tube, Provided inVarioussizes with cup joints welded at 500mm, intervals. The top Cups are made from malleable castings to endure rough site handling, and welded bottom cups are pressed from high quality steel.
Welded Bottom Cupsare pressed from high quality steel and captive mobile Top Cups made out of malleable casting provide firm grip to Ledger Blades making the connection rigid and to endure rough site handling.
Produced from Tube thickness 3.2mm or 4.0mm
Finish of Scaffolding available are:
Standard Sizes available3000 mm2500 mm2000 mm1500 mm1000 mm
Other Sizes also available (Made to order):2800mm2300mm1800mm1300 mm
We have a large scale unit engaged in manufacturing and exporting black pipes/tubes and galvanized Steel tubes/pipes. We manufacture black tubes for a range of applications like Mild Steel tubes for structural purpose and mechanical & general engineering purpose, ERW Pipes for Scaffolding mainly but also made for other application use like water, gas & sewerage, Steel tubes for idlers of belt conveyors, water wells and Lancing Pipes for various automotive & industrial applications.
Intermediate Transom provides a safe mid-bay support for38mmscaffold boards. They hold the ledgers in their jaw sections and prevent the central bending of the platform boards.
Thefabricated jawsection at each end is turned downwards to prevent dislocation. One end is provided with an integral locking device to prevent movement along theledger during use.
Produced from Tube thickness 3.2mm /3.0mm Thicness
Finish of Scaffolding available are:
Put this data instead of earlier for Sizes available below.------
These are available in following sizes2.5 M1.8 M1.6 M1.2 M
(Other Also can be manufactured as per Project/ Client requirements)
Designed to increasethe overall width of the platform to seven or eight battens. Locates at the cup joint. Incorporates a cup joint for an additional inside ledger tojoin hop-up bracketstogether to prevent movement. Facility for location of handrail post if required. Platform Brackets enable 2 or 3 plank wide platforms to be placed between the scaffold and the workface. The blade end locates into the cup on the standard and the ends of the brackets are connected to each other with Tie Bars. |
To provide a clear span between scaffolds. 305mm deep and 305mm centre to centre rungs. Constructed from48.3mm O/D x 3.2mmhigh tensile steel and saddle welded at every joint, they fully integrate with existing fittings.
Finish of Ladder Beams are available are:
Length: 3.00 MLength: 4.80 MLength: 4.00 MLength: 6.00 MLength: 6.40 M
Cantilever Frames support the formwork beyond the external periphery of the slab. The frames have blade ends for locating in the cup joint & accept adjustable jacks in three positions of 1.2m, 1.25m & 1.3m. Engineered to support normal access loads and stop-end forms; a safety device is incorporated locking that they cannot bedislodged when striking. Provision is made |
Scaffold Steel Boards 38mm x 225mm, graded to a 1.2m maximum support centre (670kg per m). Selected european white-wood. BSI Kitemarked. BS 2482:2009
AllSteel boards fittedeach end with galvanised hooping irons that are pressed in at the end and nailed round the side. Preservative treatment option (BS8417:2003). Fire retardant treatment option.
Scaffold Steel Boards These are manufactured as per customer Specification and Sizes.Commonly Steelboard sizes are below:-
225 MM X 62 MM X THICKNESS225 MM X 44 MM X THICKNESS225 MM X 38 MM X THICKNESS
240 MM X 42 MM X THICKNESS240 MM X 45 MM X THICKNESS
250 MM X MM X THICKNESS250 MM X 45 MM X THICKNESS
210 MM X 45 MM X THICKNESS250 MM X 42 MM X THICKNESS
Thickness: Varies as per customer requirements: 1.2mm / 1.5mm /1.8mm 2.0mm /2.5mm)
Lengths:Normally produced Lengths are: 4 MTR/ 3 MTR / 2.50 MTR / 2.0M MTR / 1.20 MTR. However, we can produce special other lengths also as per customer requirements.
Finish of Steel boards available are:
Cliff are suppliers of wooden boardsthat is from sources certified manufacturers in Austria, Sweden and New Zealand Stocks sizes are3.9m, 3.0m and 2.0m, but other sizes are available to order. BANDED AT BOTH ENDS WITH GI BANDS Standards as per BS 2482 |
Galvanized Pipes & Tubes has long been one of the most used building materials in the world. Galvanized Pipes resist the attack of wild, water & road salts.Galvanized steel if the one, that s been covered with a layer of zinc metal. During galvanizing, steel is immersed in a molten zinc bath, ensuring a tough, uniform barrier coating. Zinc s natural corrosion resistance provides long-term protection, even in outdoor environments. |
Pressed joint pin coupler, which has the tube size of 48 mm and nut size of 21. Made with sheet metal, these are zinc plated. Our pressed joint pin couplers are suitable for the internal connection of two tubes end-to-end. Following are the specifications: Provides end to end connection of scaffold tubes. Operates by being inserted internally and expands to apply grip against the inner walls of the tubes. The fittings are designed only forcompression joints, and should not be used where tension can bedeveloped in the tubes.Following are the specifications: |
Thetie rodwe manufacture getsheavily utilized in hydraulic press, power press, injection moulding machineand many more. Our tie rod is made to carry tensile loads for its capacity. The highly capable tie rods are made strong enough to bear the rigors of daily driving. While driving, the car will require aheavy duty tie rodto effectively lend support to the cars under chassis. Tierods allow a variety of applicationsin formwork tie systems. They have a cut threading and are available in 6 Mtrs. length or as per length required. Tie rods have been developed for reinforced concrete and tying applications, Offering an economical solution where threaded joints or couplers are required. |
We provide Water Stopper that are available in standardized dimensions, the range can also be altered to meet the specific requirement of the clients. water stopper is compatible with 17mm tie rods, for achieving water tight ties .Water stoppers are made from high quality casting and have a plastic caps at both ends, special feature is an additional surrounding disc for better Anchoring and further security against penetrating water. SIE water stoppers are optimal choice for contractors. |
We are manufacture and offer a wide variety ofwing nutsthat is made of qualitative raw material. The entire range has been appreciated for their durability, corrosion resistance and other features. Available instandardized dimensions, the rangecan also be altered to meet thespecific requirement of the clients. Wing nutsare generally considered by most to be a weaker type of nut, but this isnot necessarily the case. The wing shaped protrusions are thought to be easy tobreak off, and the extra size makes them more vulnerable to corrosion. This is whyyou will find that most wing nuts have a hex head on them just like a normal nut. Thisis just in case the wings break off and the nut needs to be removed or tightenedwitha wrench. |
We are professional manufacturer and exporter of all scaffolding fittings and accessories. We also supply other products such as ledger, bottom cup, ladder and so on, with current production capacity about 400 containers per year. Currently we have over400 employees, with over 20, 000 squaremeters land, workshops and offices buildingaccounting about 8, 000 square meters. We are dedicated to offering an unprecedented level of quality to all our customers and have built ourreputation on quality and services.
OurProp nutsare made up of good quality as per customers requirement. These are available in various sizes and specifications. These are widely appreciated by our customers for its durability and quality. We provide the best possible engineering and manufacturing platform for current and new designs with highquality, quick response time and competitive prices.
The Prop nuts are made in our very high precision foundry attached to a CNC Tool Room for making high accuracy tooling requirements.
Counter Platefor typical tie bar application with wing nuts and tie rods. Reinforced design, made from steel.waller plates/Counter Platesare for use both with timber and steel framework. waller plates/Counter Plates are of square dimensions of120x120mm, an opening hole to pass through tie rods and additional mailing holes for timber framework if required. waller plates/Counter Plates are available with orwithout galvanizing.
Anchor Nuts are specially designed to provide strong and vibration proof threads in thin walled materials and can be quickly and easily be fitted. Thin sheet fastening usually requires weld nuts of drilling and threading. Anchor Nuts is an advance assemble product and have the advantages of high-efficiency riveting, firm fastening, easy and convenient installation, reliable property, nice looking, etc., |
We are offering a wide range of Jack Nut , which is robust and known for corrosion resistance. These are dimensionally accurate and durable thus, widely utilized in engineering industry. Offered at industry leading price, these are in accordance with set industry standards. Further, these can also be customized to suit varied client's requirements.
Anestablished company, we are involved in making jack nuts for various industrial purposes. These jack nuts have accurate dimension and application specific design.We offer our jack nuts in different options as per the specificdemands of the patrons.
TheProp Nuts Heavyare made up of good quality asper customers requirement.These are available invarious sizes and specifications.
We are one of the leading manufacturers and suppliers ofAdjustable telescopic prop nuts. Our range of Industrial Telescopic Prop successfully caters specific needs and requirements of customers. These Adjustable Telescopic Spans are made from the finest raw materials to ensure total quality and complete satisfaction of customers. It has a unique design to give exceptionally high load bearing capacity for its low weight.