Changzhou aodelong Clutch Co., Ltd.

Changzhou, China

Bseu series cam clutch was developed as european style backstopping cam clutch which has easy usage. It has cam & roller construction that the roller works as a bearing same as the small size bs series cam clutch. The outer race has special shape which was combined the torque arm, so only stopping th rotation is required.You can select the correct model from various bore size from 20 mm to 90 mm in each 5 mm.Backstopping for the country elevator or the foods conveying conveyor which is used in the factory is the recommendation. Tsubaki recommends bs series cam clutch in the very dusty environment condition or the inclined conveyor and the bucket elevator which are used in outside location.Email:aodelongclutch@foxmail.comhttp:www.aodclutch.com bseu25-20 20 6 2.8 216 500 83 42 35 12 40 90 15 35 5 1.0 bseu25-25 25 8 3.3 216 500 83 42 35 12 40 90 15 35 5 1.0 bseu40-20 20 6 2.8 1, 440 450 118 60 55 15 40 110 15 35 8 1.5 bseu40-25 25 8 3.3 1, 440 450 118 60 55 15 40 110 15 35 8 1.5 bseu40-30 30 8 3.3 1, 440 450 118 60 55 15 40 110 15 35 8 1.5 bseu40-35 35 10 3.3 1, 440 450 118 60 55 15 40 110 15 35 8 1.5 bseu40-40 40 12 3.3 1, 440 450 118 60 55 15 40 110 15 35 8 1.5 bseu70-45 45 14 3.8 3, 140 350 165 90 59 20 80 140 18 35 10 1.5 bseu70-50 50 14 3.8 3, 140 350 165 90 59 20 80 140 18 35 10 1.5 bseu70-55 55 16 4.3 3, 140 350 165 90 59 20 80 140 18 35 10 2.0 bseu70-60 60 18 4.4 3, 140 350 165 90 59 20 80 140 18 35 10 2.0 bseu70-65 65 18 4.4 3, 140 350 165 90 59 20 80 140 18 35 10 2.0 bseu70-70 70 20 4.9 3, 140 350

We are offering type as is a roller type freewheel non-bearing supported. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. Nominal outside dimensions are the same as series 62.ball bearings.A typical arrangement is to install this type alongside a series 62 bearing within the same location tolerances, as shown on the following page. The inner race is keyed to the shaft (except 6 mm bore).The outer race has a positive r6 tolerance to give a press fit in a h7 housing. The outer housing must be strong enoughto not expand after assembly. This design can accept an axial misalignment of inner and outer race of s2type size overrunning speeds weight dragtorqueas (nss) dh7 tkn1) nimax2) namax3) dr6 d5 l s e f tr[mm] [nm] [min-1] [min-1] [mm] [mm] [mm] [mm] [mm] [mm] [kg] [ncm]6 2.1 5000 7500 19 15.8 6 0.3 0.6 0.3 0.01 0.188 3.8 4300 6500 24 20 8 1.3 0.6 0.6 0.02 0.2410 6.8 3500 5200 30 25.9 9 1.3 0.6 0.6 0.03 0.3612 13 3200 4800 32 28 10 1.3 0.6 0.6 0.04 0.4815 14 2800 4300 35 31 11 1.4 0.6 0.6 0.05 0.720 40 2200 3300 47 40 14 2.4 0.8 0.8 0.12 1.425 56 1900 2900 52 45.9 15 2.4 0.8 0.8 0.14 2.430 90 1600 2400 62 55 16 2.4 0.8 1 0.22 7.835 143 1300 2000 72 64 17 2.5 0.8 1 0.31 940 185 1200 1800 80 72 18 2.5 0.8 1 0.39 10 45 218 1000 1600 85 77 19 2.5 1.2 1 0.44 11 50 230 950 1500 90 82 20 2.5 1.2 1 0.49 13 55 308 800 1300 100 90 21 2.5 1.2 1 0.66 14 60 508 700 1100 110 100 22 2.5 1.2 1.5 0.81 26 80 1063 600 900 140 128 26 2.5 1.2 1.5 1.41 58