Hebei Annuo Automation Technology

Shijiazhuang, China

13.52.83.5m821612

All the galvanzing furance and equipments are pre-fabricated and delivered construction site. our engineer guide the installation.

Cost effective, fast and easy installation greatly shorten the construction time which reduce the cost

also We provide the galvanizing traning service for the clients.

At present, in some industries, some industrial devices are needed, hot dip galvanizing is one of them, can bring some help to manufacturer and businessman, so how to choosehot dip galvanizing plant? This problem is very common actually, also be the attention of a lot of manufacturer. It is also very good to be able to provide a lot of manufacturers with good services, thus can promote the progress of the entire era.

Hot dip galvanizing factory is in when choosing, can see a few coating respect, see next evenness, good plating layer is compared ground is meticulous even. At the same time, surface defects such as zinc flow pattern, leakage plating, zinc fluctuation and zinc slag cannot exist. At the same time, the roughness of the surface can also be observed. The roughness of galvanized sheet can be greatly influenced by the light finishing process after hot plating.

Manufacturer still can see coating composition to prevent, the content of coating composition of good hot galvanization board coating component will exceed 99 %, at the same time base plate also is the key that people pays attention to research, such ability can better satisfy manufacturer's demand. The weight of coating or thickness, also want to accord with the demand of manufacturer, want moderate coating size to be able to accord with the demand of manufacturer truly, bring certain help effect to manufacturer better thereby.

Hot dip galvanizing plantshould choose to have after sale service, such ability can be used in the process, get certain safety safeguard, bring to the development of whole times better thereby certain positive effect, this also is the need of a lot of manufacturer at present. Times are improving, so some industrial equipment should be carefully selected, so that manufacturers can better help.

Hot galvanizing is a metal anti-corrosion process. Hot galvanizing is used to produce protective film on the metal surface, which can prevent chemical reactions between the metal and the oxide in the air. Metal and steel workpieces are used in different environments, such as land and sea, which require good performance. Can choosehot galvanizing linesupplierto buy good products.

Hot-dip galvanized steel workpieces are less likely to corrode, and manufacturers need not worry about making such metals. Nowadays, with the development of industry, there are many industries that need metal products. Metal products are in great demand and the quality of products is strictly required. If be like traditional metal product so anticorrosive performance is bad, if use, have little advantage, what affect is construction efficiency. Hot dip galvanization metal product is in nowadays use range is extensive, because galvanization product has protective film, not easy suffer corrode, use order is ordered for a long time. Need to buy such products, can contact the hot galvanizing line supplier.

Mr. Yang just needs a batch ofhot dip galvanization linequite a few, through the website of network shopping found out a few good hot dip galvanization linesale business, had the understanding to these business case and the product that sell, selected our hebei anno to cooperate thereby. And Mr. Yang our price may not be the lowest, but our business reputation, product quality, after-sales service is certainly ahead of other businesses.

To become anhot dip galvanizing plant exporter, it is also necessary to have comprehensive consideration in service. It is necessary to make appropriate development plans in advance, establish a good service form, provide a good service form according to the customer's problem needs, reduce the possibility of problems, promote the industry to operate in a stable direction, and the production and processing efficiency are also very good. Upgrade.

Manufacturers with professional production equipment can choose the best manufacturers first. Find the manufacturer on the Internet, see the types and models of equipment introduced by the manufacturers, and see the sales of the equipment of the manufacturers in the market. The best thing is to look at the reputation of equipment manufacturers, choose a reputable manufacturer to cooperate, do not worry too much about the quality of the equipment, and the price will not be very outrageous. Looking for manufacturers is not only to buy production equipment, but also hope that manufacturers can come to the design layout of the plant. Looking for reliable manufacturers, not only haveHot dip galvanizing equipment, plant layout and production line layout can be assured, professional manufacturers provide better services.

There are a lot of things to be aware of when purchasinghot dip galvanizing machine. When selecting equipment, you must do a good job in understanding all aspects and choose comprehensive application requirements. In addition, we must be optimistic about the operation of the machine, whether it meets the actual production and processing needs, ensure stable operation, good protection for steel and other components, support better production and processing, and have a long and stable service life.

what kind of equipment is good? the manufacturer needs a production line to be able to produce the product. The complete production line is from the loading to the inspection and packaging. The equipment to be used includes galvanizing furnace, zinc pump, pickling tank, etc. Also depends on the production design. To establish a hot-dip galvanizing plant, you can find a mature and experienced manufacturer to understand, the equipment used can also be purchased from other manufacturers. Which production line equipment is good? the selection of equipment mainly depends on the quality, the quality of the equipment is good, and the cost is reduced during the production process. The equipment used for thesmall parts galvanizing linesis low in price and the quality is not satisfactory.

With the development of economy, technology has been paid more and more attention by all walks of life. We of the kind of national infrastructure, industrial galvanizing plant manufacturertechnicaldevelopment has played a significant role in the modernization drive, but the development of science and technology and production requirements for industrial galvanized the technical requirements of more and more is also high. As a first-class industrial zinc plating equipment manufacturer, we can provide you with super - class equipment, providing super - class production services.

Our industrial zinc plating equipment manufacturers can assist manufacturers to complete research and production, overall planning, energy assessment, environmental assessment. We can also provide you with one-stop service of factory design, process design, equipment design and manufacturing, installation and debugging, production guidance to raw and auxiliary materials, professional technical personnel training and so on.

And as the country's emphasis on environmental protection, we industrial galvanized equipment manufacturers have been four major link of the process of hot galvanizing production seriously explore and absorb the introduction of foreign advanced experience of the industrial galv

At the current international situation, galvanized equipment processing is a technology of the current market demand is bigger, it is widely used in electric power tower, communication tower, railway and highway protection, lamp posts, substation auxiliary facilities, etc. The environmental protection performance ofhot-dip galvanizing equipmentis also concerned because some waste gas and iron waste are produced in the process of galvanizing.

There are three ways of galvanizing: 1. Acid galvanizing; 2. Basic zinc plating;3.Hot galvanizing. Naturally, the equipment used in these three galvanizing methods is not the same.

Now, ordinary galvanizing did not meet the international environmental protection requirements, and the quality has high, low, uneven. We all know that waste gas and water will be produced in the process of zinc plating. If it is not treated, it will be directly discharged into the air or water resources, which will cause irreversible pollution to the environment and water resources. This is very much out of line with today's environmental themes.

hot dip galvanizing plant exporter they on ordinary steel material is very exquisite, especially they have the above requirement is that all the outside steel pipe shall not be mixed with any even just a bit of stain, because as long as it is a little stain, it may lead to the final products produced serious is unqualified, unqualified products will not be able to export, at the same time, in the domestic sales volume is very low, and the price is very low.

In steel pipe before and after production, steel tube in the event of any deformation, also must be correct, because appear this kind of circumstance, for export is very large, we are hebei general-secretary galvanizing plant exporters have very high to the requirement of product, we will have to be the best products to foreign countries, because foreign degree is very high for the attention of the product, but a little bit of flaws are likely to result in the loss our reputation continuously, in order to prevent this kind of situation, we in the domestic control must be done well.

When choosing the exporter ofhot dip galvanizing plant exporter, many people will not make the choice, and the final result is not satisfactory. Some customers are not satisfied because the picture is cheap. There are certain standards for choosing a good exporter of hot-dip galvanizing plant.

Good credit or not

Since an exporter of hot-dip galvanizing factory wants to sell his products to foreign countries, the problem of reputation is very important. If the foreign people are not satisfied with the products when exporting, we can't choose this exporter. A businessman is based on good faith, without which he will not have a good reputation. Therefore, when selecting exporters, the first factor to consider is the credibility of exporters.

the biggest advantage of hot galvanizing equipment manufacturing is that it has a long antiseptic time and a wide range of environment to adapt to. Hot galvanizing is widely used in electric power tower, railway, communication tower, road lamp pole, building steel structure component, marine component, substation accessory facility, light industry and other places.

what are the advantages ofhot-dip galvanizing equipmentmanufacturing? why should we choose hot galvanizing?

the first is the cost problem, which is very cheap to deal with: the cost of hot dip galvanizing for rust prevention is lower than that of other paint coatings;

the second is durability: in harsh conditions, the standard hot-dip galvanized rust protection thickness can be maintained for more than 50 years without repair; especially in urban or offshore areas, the standard galvanized antirust layer can be maintained for 20 years without repair;

the third is the strong reliability: the galvanized layer and steel are the metallurgical combination, and finally become a part of the steel surface, so the durability of the coating is relatively reliable;

the fourth galvanized layer has strong toughness: the galvanized layer will form a very special metallurgical structure, which can withstand the damage caused by mechanical collision when the equipment is transported and used.

to some understanding of the galvanizing production line is very small, so today we are going to share with you about galvanized production line how to correctly grasp the processing time, let's put the acid mist processing equipment, the problem such asgalvanizing production lineprice, put down, take a look at "solomon's hot galvanizing equipment is how to determine the processing time, hope you can know more in use process in the future. Now we're going to get down to business.

how does hot dip galvanizing equipment ensure a reasonable dip time?

if the zinc immersion time ofhot-dip galvanizing equipmentis too short, the surface zinc ferroalloy layer is not fully formed and the surface is not smooth. Over time, the thickness of the hot zinc layer will be too thick, resulting in unwarranted waste of zinc consumption and adhesion reduction.

often down, said steel in the zinc bath immersion plating time is not sure, but usually we no longer have to zinc bath surface zinc ash is generated, usually between 0.5 to 2 minutes time, while relatively thick steel need longer zinc immersion time. Zinc dipping time don't need to have a fixed standard, but must according to the different thickness of the steel temperature, material, process factors such as comprehensive consideration, the other is in hot galvanizing equipment production experience is very important.

through the introduction of this article, I believe you for "hot galvanizing equipment correct processing time" had certain understanding, if you want to know zinc trough, galvanizing production line, and other related knowledge, please contact with us!

The biggest advantage of hot galvanizing equipment manufacturing is that it has a long antiseptic time and a wide range of environment to adapt to. Hot galvanizing is widely used in electric power tower, railway, communication tower, road lamp pole, building steel structure component, Marine component, substation accessory facility, light industry and other places.

What are the advantages ofhot-dip galvanizing equipmentmanufacturing? Why should we choose hot galvanizing?

The first is the cost problem, which is very cheap to deal with: the cost of hot dip galvanizing for rust prevention is lower than that of other paint coatings;

The second is durability: in harsh conditions, the standard hot-dip galvanized rust protection thickness can be maintained for more than 50 years without repair; Especially in urban or offshore areas, the standard galvanized antirust layer can be maintained for 20 years without repair;

The third is the strong reliability: the galvanized layer and steel are the metallurgical combination, and finally become a part of the steel surface, so the durability of the coating is relatively reliable;

The fourth galvanized layer has strong toughness: the galvanized layer will form a very special metallurgical structure, which can withstand the damage caused by mechanical collision when the equipment is transported and used.

The fifth comprehensive protection method: every part of the plating can be galvanized, even the pits, sharp corners and hiding places can be fully covered.

Sixthly, it is relatively time-saving and labor-saving: the galvanizing process is more convenient and efficient than other coating construction methods, and it can avoid the time required for painting on the site after installation.

The above is the article about the advantages ofhot-dip galvanizing equipmentShared by the editor. It will be updated in the future.