Our Products #1639229

Chiller Temperature Controller :A special action for -50.0C to 50.0C range having independent setting for tember as well as delay time (time m for which Comres- sor has to rest before restarting) Hysteresis is also settable between 0.2C to 9.9C. The delay time is helpful in increasing the working life of the compressor. This is also available for two compressors ( independnet temperatures and the settings) and three compressors.

Temperature Controller with Soak :For heat treatment apipilication addiptional time setting time setting is available to maintain the temperature of the furnace or ovan for the desired set time (0.999min) after the temperature has reached the set value.

BOD Controllers :For controller of ovan temperature below or above m ambient temperature. The heating or cooling realy will turn on depending on whether wt temperature is above or below the ambjent temperature. Second sensior for sensing ambient temperature is provided. Both relays have independent hysteresis sellings (by keyboard).

Temperature Controller With :The facilitynis used in heat treatment or settable rate of rise of temp material testing equipments .Rate of rise is settable by keyboard from 0 to 10C/min

Profile Temperature Controller :This is useful in obtaining variable temperature profile in an ovan or furnace for heat curing application. The time and temperature data can be led by the keyboard, control action can be on/off or time propotional. this is also useful for testing purpose in Laboratory (Calibration Bath).

PID Temperature Controller (Proportional, Integral & Derivative) :This is useful for precise control of temper ature in an ovan, furnce, plastic machinery etc. when job requires high heating during initial period & low heating when temperature stabilizes. Derivative action overcomes sudden changes in temperature due to load changes, integral action corrects the accumulated error.

Derivative time constent and intergal time constant have to be set suitable for the machine whose temperaturemis to be controlled, initially, trial and error methodmis required to select these parameters, but once they are set the action gives better control of temperature.
Relay output for control of contractor or pulse output for control of SSR is provided. Optionally 0 - 10V output can also be provided for control of SCR firing units.

Controller with Analog Input :This is useful in application where transducers are used (i.e. load cell, flow sensor, pressure sensor etc.) The signal can be ) -10V or 4-20m A D.C. Like in other controllers, single set point and two point models are available. These relays can also be used as alternative settings, Calibration through key board is possible.

A wide range of photoelectric sensors, fiber optic cables, & accessories. We have the photoelectric sensors you need to keep your applications running. Pepperl+Fuchs with the brand VISOLUX is an innovator of photoelectric sensing technologies. For precise, optical control of positioning, sorting, & counting processes & for custom non-standard applications, look to Pepperl+Fuchs to have the answers for every industry.

Ultrasonic sensors present the ideal solution for non-contact position and distance measurement in all industrial areas where environmental conditions such as dust, smoke or steam may affect the sensors. Objects consisting of a variety of materials can be detected to within millimeters regardless of color or shape.

The ultrasonic sensor produces a data carrier utilizing very high frequencies that are outside the humans audible range. The time it takes for that ultrasonic wave to pass between the sensor and the object is the value for the distance or the position. Ultrasonic sensors have proven their reliability and precision in many industries, including lumber and furniture, construction materials and equipment, farming equipment and in level control applications.

Pepperl+Fuchs ultrasonic sensors currently encompass 8 series of mechanical designs for through-beam, direct detection and retro-reflective operation with more than 40 designs and models. Customer and application specific custom solutions underscore our technological competence in this area of sensors.

Product features:

Devices with TEACH-IN functionality for fast and simple installation.

ULTRA 2001 software for improved adaptation of sensors to applications (for devices with RS 232 interfaces)

Temperature compensation equalizes deviations in sound velocity due to varying air temperatures

Synchronization input to prevent cross-talk interference when sensors are mounted within close proximity of each other

Sensors with digital and/or analog outputs

Identification systems are used for object identification. They can be used to automate manufacturing processes and to control the entire logistics of merchandising management through flexible networking. This reduces throughput times and makes variant manufacturing more flexible. Pepperl+Fuchs offers a comprehensive range of electromagnetic identification systems (RFID). Object identification is also possible using barcodes and data matrix codes.

The Actuator/Sensor Interface (AS-Interface) is a replacement for conventional wiring systems, designed to significantly reduce installation and startup times while increasing diagnostics. AS-Interface utilizes a 2-conductor flat cable to supply power to field device (I/O blocks, encoders, and even safety devices.) Installations based on AS-Interface posses several advantages including:

Only one 2-conductor cable is needed to connect hundreds of I/O points
Standard I/O and safety devices coexist on a single network
Superior noise immunity
Fast and deterministic update times

AS-Interface ensures reliable data transmission in demanding industrial applications. The unshielded, non-terminated network allows adding and moving I/O points any time, even under power.

Rotary encoderscan be used in all applications that require monitoring rotation rate, speed, acceleration and direction. These sensors can be utilized in many applications found in mechanical engineering, the conveyor industry, material handling and the packaging industry. You are certain to find a suitable rotary encoder for your application from our broad product offering.

In automation, rotary encoders are used as sensors for angle, position, speed and acceleration. Linear motion can also be measured through the use of spindles, gear racks, measuring wheels or cable pulls.

Rotary encodersconvert a mechanical input into electrical signals, which can be processed by counters, tachometers, programmable logic controllers and industrial PCs.

Features

Out put power ready - Rdy signal.remote monitoring

Can be connected in parallel for redundancy

Low ripple

Over voltage protection. OVP trip point

Over load protection.Automating power limiting

Short circuit protection.Auto recovery

100% full loadburn - in test

DIN RAIL (TS35) / panel mountion

Compact - Economical

C&S ACB, conforming to IEC 60947 Part 2 and IS 13947 Part 2, are available from 630A to 6300A, 3 pole as well as 4 pole, in all possible versions - Fixed or Drawout, Hand operated or Motorized. The 4 pole incorporate true 4th pole - rating & contacts same as the main poles but with advance closing and delayed opening mechanism to avoid any Switching Surges and Remnant Transients.

Accessories

All commonly required Accessories are also offered along with them as per the customer choice - Auxiliary Switch, Shunt Release, Under Voltage release, Position and Indication Micro-Switch, etc. Also offered are certain Special Accessories like Capacitor Trip, Mechanical Inter-lock kit, different types of Busbar termination kit, etc.

User Friendly, easy to operate and maintain

C&S ACB have features to make it very simple to operate. All type of ACB - even the Manually operated type come with Ratchet charging mechanism to enable effortless, gradual charging of mechanism spring so that, even highest rating ACBs can be charged very easily by any operator. All controls are visible and available in front - Auxiliary Switch, Sliding Contacts, etc. All the accessories like Shunt, closing coil, Under Voltage, etc are fitted in front and do not require calibrations

Safety Built-In

The Drawout ACB can be racked in or out only when the TRIP push button is pressed thus ensuring ACB will not be racked in CLOSED condition. Safety Shutters are supplied as standard. Sliding window in front of both push button - CLOSE and TRIP, facilitates pad locking and avoiding un-authorized operation while maintenance.

National & International Certification

These ACBs have been tested at various laboratories for their conformity to various standards - ASTA, CPRI, ERDA, etc and meets the Safety requirements as per European standards to carry CE marking. They have also undergone rigorous testing to establish their suitability for Marine applications.

Applications

These ACB are fit for use in diverse application and are in use in various industries for last more than 15 years - Power Plants, Gas & Petro Chemicals, Steel, Chemicals, Automobile Industry, Telecommunication & Infrastructure, Buildings and Commercial Complexes, etc. They are also being used in some of the very special applications - DC applications, 690 Volts system, Marine & Naval applications, etc.

The U series Terminal Blocks are based on Modular Type design having all Brass parts. The proven screw clamp design offers high compact force and is easy to use. The special design of the clamp makes it possible to terminate upto 0.2 sq.mm conductor on the lower side. All metal parts are made up of high conductivity brass. The housing is made from engineering thermoplastic type Polyamide 6.6. The feed through terminal blocks are available currently to accommodate conductor sizes from 0.2 sq.mm to 10 sq.mm. The Twin Terminal Block solves the problem of power distribution by accommodating two separate cable connection points on the load side. The Double Level Terminal Blocks offer easy solution to space problem. The special feature of providing offset between lower and upper decks allows better accessibility to the lower level screws and better visibility of labels.

Solving a wide range of applications in one system, our K-System guarantees a reliable and economical signal transmission between your field device and the control system. Whether your plans include a single isolating module or a large scale system integration, application-oriented solutions characterize the entire K-System product range.

Product portfolio

The K-System offers an extensive range intrinsic safety interface modules for many signals and applications - from simple isolators to highly functional modules.

Power Rail

The Power Rail is an insert in the standard 35mm DIN rail. When mounting on the DIN rail, the units are simply snapped in place. The Power Rail supplies the modules with power and provides a path for the collective error message from individual isolators. Power Rail reduces wiring and maintenance costs because it eliminates the need to daisy chain the wires. It also simplifies expansion. Just snap in a new module when you're ready to add to your system.

Power Feed Modules

The Power Rail is an insert in the standard 35mm DIN rail. When mounting on the DIN rail, the units are simply snapped in place. The Power Rail supplies the modules with power and provides a path for the collective error message from individual isolators. Power Rail reduces wiring and maintenance costs because it eliminates the need to daisy chain the wires. It also simplifies expansion. Just snap in a new module when you're ready to add to your system.

International safety standards

SIL ratings are available at no extra charge.

Easy Configuration

With our powerful software tool, PACTware, Project documentation is easier to create and highly functional interface modules are easily configured.

Digital Analog

Input Isolated Switch Amplifiers Transmitter Supply IsolatorsPulse Analyzer Units ConvertersRelay Modules Trip AmplifiersOutput Solenoid Drivers Isolated Repeaters