Our Products
t is used for sterilization under saturated steam pressure at any selected point between 10 to 20 p.s.i. (adjustable). These are double walled units with inner chamber (Boiler) made of 18 S.W.G. stainless steel and outer chamber is covered with S.S. Lid is tightened by wing nuts / radial locking system (AS ORDERED). Fitted with neoprene rubber gasket, all systems are hydraulically tested upto 40 p.s.i. as a safety measure. All autoclaves are fitted with saandrad accessories such as water level indicator, pressure gauge, steam release cock, spring loaded safety valve and heating element. Supplied complete with S.S basket, cord and plug to work on 220/230 volts A.C. Supply.V
Light weight with ceramic fibre wool insulation (instead of Brick insulation). The outer casing is made of double walled thick P.C.R.C. Sheet, duly painted. Heating elements are made of KANTHAL "A-1" wire and backed by high temperature cerwool insulation, which avoids loss of energy. Temperature is controlled through Digital Temperature Indicator- cum-controller. To work on 220/230 volts or 400/440 volts A.C. Maximum Temp. is 10000C and working temp 9000C. For models of higher temperature the maximum temp. is 12000C and working temp. 11500C.
hese are sturdy double walled units with outer chamber made of M.S. sheet duly enamel with inner made up of anodized aluminium or S.S. sheet. The gap between inner and outer chamber is filled with high grade glass wool to avoid thermal losses. Beaded heating elements are placed in ribs, at bottom and sides. Inner chamber is provided with ribs for adjusting perforated shelves to convenient height. Temperature is controlled by imported hydraulic type capillary thermostat from 500C to 2500C 10C. An-L shaped prismatic thermometer is fitted to the unit for reading the chamber temperature. Air ventilators are also provided on the sides of the unit. To work on 220/230 volts A.C.
(a) Air Circulation fan can also be provided at an extra cost
(b) Mechanical timer (2 Hrs) at an extra cost
(c) Microprocessor based PID temp. Controller-cum-indicator instead of Thermostat
(d) Digital Timer of 1 hour can be Provided.
ner Camber Size | Cap |
(a) 300 x 300 x 300 mm | 28 ltrs. |
(b) 355 x 355 x 355 mm | 45 ltrs. |
(c) 455 x 455 x 455 mm | 95 ltrs. |
(d) 455 x 455 x 605 mm | 125 ltrs. |
(e) 605 x 605 x 605 mm | 224 ltrs. |
(f) 605 x 455 x 910 mm | 252 ltrs. |
(g) 605 x 605 x 910 mm | 336 ltr |
Double walled with inner chamber made of S.S. and outer of thick PCRC sheet duly enamel painted. Temperature range from ambient to-200C is achieved by hermetically sealed compressor. The gap between the inner and outer wall is filled with high grade mineral glass wool to avoid thermal loss. Body is mounted on a sturdy angle iron frame and mounted on castor wheels. Unit is fitted Solid State Digital Temperature indicator-cum-Controller. Vertical models are supplied with three stainless steel storing shelve.
|
Based on the rotating disc-splash plate principal. It produce only super fine particles of micron size, which become part of the atmosphere, thereby reaching every corner of the room, resulting in uniform humidity. Due to the upward thrust imparted to the micron size water droplets, by high speed motorized Unit, they remain suspended in the atmosphere for longer duration of time. The unit is capable of atomizing upto 3 liters of water in an hour at full evaporation in the dries possible ambient condition. The unit has body made up of S.S. A single unit is effective for an enclosed space of volume upto 40 cu. Mtrs. The unit is provided with high speed 2800 RPM motor to run longer period, and the blades are aerodynamically balanced to ensure fumigation. To work on 220/230 volts A.C. supply.
he unit is recommended for making pyrogen free distilled water of a very high degree of purity. Made out of S.S. special kettle element is fitted with Ejection Device/ Auto cut for safety of the element in case water supply is stopped. The cock fitted to the unit is of brass C.P. A wall mounting clamp is provided with the unit but without rubber tubing. Supplied with cord and plug to work on 220/230 volts A.C. supply. (S.S-304 GRAD ARGON ARC WELDED)he unit is recommended for making pyrogen free distilled water of a very high degree of purity. Made out of S.S. special kettle element is fitted with Ejection Device/ Auto cut for safety of the element in case water supply is stopped. The cock fitted to the unit is of brass C.P. A wall mounting clamp is provided with the unit but without rubber tubing. Supplied with cord and plug to work on 220/230 volts A.C. supply. (S.S-304 GRAD ARGON ARC WELDED)
The assembly consists of Borosil glass flask with embedded heating elements fused in spiral type glass coil internally at bottom. A double wall coiled condenser has standard ground glass joints. Complete with glass fitting, metallic stand, rings clamps and electrical fittings. The unit supplied is as per NPL patent design. To work on 220/230 volts A.C. supply.
It consists of an in built prefilter and very high exchanging capacity non-corrosive CATION and ANION resin columns prefilled with imported Resins for efficient results having treated water parameters conforming to IS-1069/64. It yields chemically pure water equal to multiple distilled water having a conductivity of less than 10 microsiemens/ cm and ph of 7.5 to 9 ph. Fitted with a sturdy PVC multi control valve and can be connected direct to water taps. Fitted with digital conductivity meter. Supplied with one plastic chemical proof regeneration tank and the complete unit in housed in a painted M.S. Trolly for easy mobility.
The apparatus consists of an evaporating flask rotated by heavy duty motor in a heating water bath (optional). Vacuum distillation of solvent at high and low temperature is achieved quickly and efficiently by use of a variable speed motor, which prevents foaming and bumping of the liquid (solvent) into the evaporating flask and also distillation under controlled atmosphere. The evaporating flasks is pear shaped to give a large surface area of evaporation and is clamped to a glass duct which goes through the drive unit and protrudes about 120 m.m. into the condenser. The condenser is fitted with standard joint at the bottom for receiver flask. The unit is fitted with a quick action jack.
CAPACITY 1 ltr. 3 ltr.
Consists of S.S. Holders in manifold of 3 or 6 holders for 47 m.m. Dia membrane filters. The tops of the holders are connected to the outlets of the flushing tube with silicone tubing and glass stop cock. A vacuum resistant flask or woulfs bottle must be placed between the manifold and vacuum pump. (Supplied without woulfs bottle and vacuum /pressure pump.). These units are used for sterility testing when the membrane filter is to be removed from the holder for incubation in culture media. Filteration areas is 12.5cm and has a holding capacity of 250ml. through only vacuum is required for filteration, some pressure is required for flushing liquids.
(a) 3 Branch Sterility Test Unit. (Made from SS-316 filters of dia 47 m.m. (250 ml. cap)
(b) 6 Branch Sterility Test Unit (Made from SS-316)
It has compact stirring device utilizing a rotating magnetic field (created by a PERMANENT MAGNET) which induces variable speed stirring action. Stirring is accomplished by means of small Teflon rotor, which when placed in the liquid to be stirred is capable on rotation by magnetic field applied from below the container. The unit is fitted with pilot lamp. To work on 220/230 volts A.C. supplied complete with one stirring Teflon bar.
Gyratory sieve shaker is driven by 1/4 H.P. Electric motor through a reduction gear, can carry up to SIX, 6" OR 8" Test Sieves with one set of LID and PAN. This gyratory motion of the table there is an upward and downward movement but is inclined from the vertical axis and the direction or inclination charges progressively in clockwise direction having frequency of about 270 vibration per minutes (without sieves & lid & pan) Fitted with perfect motor.
This yoder type motor driven sieve shaker is for carrying out wet sieve analysis of material. Consist of a water reservoir and a holder for sieve which can take upto 7 sieve of 8" di1500C a. The shaker is driven by 1/4 HP Motor through a belt drive. Suitable to operated on 230 volts 50 cycle, single phase A.C.
Electrically operated with quick release chuck taking wide variety of interchangeable nylon brushes for cleaning syringes, test tubes, bottles etc. Model (a) and (b) are table model mounted on a heavy base and have single chuck. Machines with soaking tanks have 12 rinsers and two drill chuck to hold variety of brushes and are mounted on sturdy angle iron frame duly painted. Fitted with perfect motor.
Made DE-444 Overhead Projector is a brilliant aid for your business presentations, training classes and seminars. It projects large clear images. Irrespective of the size of the room, marinating a brilliant white screen with edge to clarity and consistency. Ensuring your comfort and facilitating smooth presentations.
Type of OHP Tranmissive | Tranmissive |
Aperture | 250 x 250 mm |
Projection Lens | Single Miniscus |
Focal Length | F-290 mm |
Lamp | 24V-250W(Twin) |
Cooling System | Silent Cooling |
Lens | 1800 |
Lamp Changer | Yes |
Foldable Arm | Yes |
Weight | 10 kg. |
Packing | Cardboard |
This is a double walled unit mounted horizontal on a sturdy, heavy mild steel tubular stand duly painted. Pressure is adjustable from 10 to 20 psi. fitted with pressure gauge, safety valve and steam release valve. Available with boiler. For units fitted with S.S. Boiler, separate valves for injecting the steam into the main chamber and releasing the steam in atmosphere after use are provided. Hydraulically tested upto 40 psi. Automatic vacuum breaker is provided to break the vacuum in case of formation of vacuum due to steam condensation. Both inner chamber made of S.S. Fitted with a Digital Temperature Indicator to indicate temperature. Automatic Pressure Control Switch and Automatic Low Water Level Cut-off devices. Lid is made of S.S. Plate provided with radial locking system. Without steam jacket.
It withstands high temperature up to 3500C. The body of the mantle is spun one piece from non-rusting Aluminium (upto 5.0 ltrscapacity)duly stoving painted. All heating mantles are lagged with special grade mineral wool. To work 220/230 volts. A.C.