We are offering bridge expansion joint material.
The bridge deck expansion joints are an important element in the functioning of bridge structures. When joints fail to function properly they can create problem out of proportion to their size. Selection of good joints for use can create fewer bridge maintenance problems there for indian ministry of roads transport & highways (mort& h) has setup certain guidelines for the design, manufacture and installation of bridge expansion joints in india.
Deevin india having a state-of-art manufacturing facility in mandideep industrial area for the design and manufacturing of expansion joints, which exceed the international quality norms.

types of bridge expansion joints we design, manufacture, supply, replace, supervision & installation
compression seal joint:
is used for smaller range movements from 0 to 40mm. It consist of two angles with an elastomeric seal. The seal is installed in compressed position this joint is ideal for replacement of old joint and for new project.
Design chart
series installation movement(mm)
csej-10 32 30
csej-20 45 40

strip seal expansion joint:
strip seal expansion joint is used for medium movement from 0 to 80mm. It consist of two edge profiles with an elastomeric seal in between. The edge profiles are generally cast into a noising of the structure. These joints expected performance life more than twenty five years. This is most popular and expected joint system among bridge consultants and engineers worldwide.
design chart
series installation width(iw) movement(mm)
ss-80 40 80
ss-130 60 130

modular stripe seal expansion joint
modular strip seal expansion joint is used for large movement from 0 to 2000mm. In addition to edge profiles, it has a series of supported intermediate beams and seals in a modular way to accommodate the movement of the joints. Each seal have a capacity to accommodate movement upto 80mm.

We are offering bridge bearing.
bridge bearings are devices for transferring loads and movements from the deck to the substructure and foundations. In highway bridge bearings movements are accommodated by the basic mechanisms of internal deformation (elastomeric), sliding (ptfe), or rolling. A large variety of bearings have evolved using various combinations of these mechanisms.
1. elastomeric
the elastomeric bearing allows the deck to translate and rotate, but also resists loads in the longitudinal, transverse and vertical directions. Loads are developed, and movement is accommodated by distorting the elastomeric pad.
2. 2. Plane sliding
sliding bearings usually consist of a low friction polymer, polytetrafluoroethylene (ptfe), sliding against a metal plate. This bearing does not accommodate rotational movement in the longitudinal or transverse directions and only resists loads in the vertical direction. Longitudinal or transverse loads can be accommodated by providing mechanical keys. The keys resist movement, and loads in a direction perpendicular to the keyway.
3. roller
large longitudinal movements can be accommodated by these bearings, but vertical loads only can generally be resisted.

We are offering Rebar Couplers.
Deevin's Rebar Couplers increase production rates because of installation time and simpler quality control requirements. Because of these differences, labour requirements cost will be substantially reduced.

Deevin India having a state-of-art manfacturing facility in Mandideep industrial area for thr design and manufacturing of Expansion Joints, which exceed the International quality norms.
Deevin's Rebar Coupler is applied to reinforced concrete construction in various kinds of construction projects. It is regarede as an innovated construction material and connection, with characteristics of 'energy-saving, environment friendly and high efficiency'. The advantages are
TECHNICALLY SUPERIOR:
DEEVINS's rebar coupler performs like continuous reinforcement, developes strength mechanically, independent of concrete. Therefore provides ductility in RCC structure independent of condition of concrete. Proven cyclic performance of rebar offers strength during man-made, seismic or other natural events. The continuity of rebar offers excellent provision for grounding electrical current.
DEEVIN'S REBAR-COUPLERS
Increase production rates because of reduced installation time and simpler quality control requirements. Because of these differences, labour requirements and cost will be substantially reduced.
DEEVIN's REBAR-COUPLERS OFFERS:
Quality, cost and time saving. Fixing couplers requires no special skills or equipments. Simple mmechnical ways in adopting mechanical splicing compared to lapping accelerates construction schedules for optimum cost efficiency.

Tying steel reinforcing bars has always been tough, manual labor, as reinforcing ironworkers spend much of the day hunched over tying rebar. Deevins's Rebar tying machine is fully automatic machine to ie rebar. The machine holds the crossed reinforcing bars, feed the tie wire, winds, cuts, and tie in one second. The result is a strong, single strand, double wrap tie. The Automatic Rebar Tying Machine can be used in numerous applications, manholes even in remote areas where the electricity is not available. Advantages of the Rebar Tying Machine include saving time through productivity it is 6-6 times faster then hand tying, reduction of on-the-job injuries, consistent results, and reduction of material cost by decreasing wire consumption and save big money and manpower.

We are offering deevin's portable bar cutting/bending machine.
deevin's rebar cutters and benders are purpose use for construction or all kind of other things that relate to rebar (steel bar, rod) cutting widely used in construction engineering. Our products are light, small quiet portable and easily to operate. Also it safe for the users, as cutting without sparks and sediment.
deevins portable bar cutter and benders have an excellent cutting & bending capacity owing to a strong hydraulic and less in weight.
dss-16cb:- its portable battery rebar cutter machine.
dss-25ce:- its portable cutter works with electricity as got wire.
dss-16b :- its portable rebar bending machine
features:
deevins rebar cutters/benders have an excellent cutting and bending facility owing to a strong hydraulic.
the blades of rebar cutter made of special material seldom wear away.
with a strict quality control, rebar cutters and benders have confidence of the best quality in the world.

We are offering mild steel plates.
Only power grid approved steel rollers for complete range of mt/ht angles from 25x25x3 to 250x250x30
exclusive trading unit for all sizes of ms/ht plates/ sheets and tmt bars.

45 x 30 mm to 3 to 6 mm
75 x 50 mm to 6 to 10 mm
90 x 60 mm to 6 to 12 mm
100 x 75mm 6 to 12 mm
125 x 75 mm 5 to 10mm
150 x 75 mm 8 to 12 mm
150 x 90 mm 8 to 12 mm
150 x 115 mm 8 to 12 mm

We are offering building expansion joint systems.
Deevin group is one of the leading innovators for building expansion joint systems for the commercial construction industry. Deevin group offers an architectural line of seismic, thermal and waterproof expansion joint systems meeting the aesthetic and structural demands of airport, metro rails, hospitals, shopping malls and other building type.


parking expansion joints
(i) pcs series
(ii) npj series
(iii) epj series (iv) hdpj series
(v) apj series

floor expansion joints
(i) gaf series
(ii) acbp series
(iii) eacbp series
(iv) afs series (v) affs series
(vi) hfw series
(vii) agp series

all expansion joints
(i) dfs series
(ii) mdfs series
(iii) aaw series
(iv) aws series (v) acpw series
(vi) sem series
(vii) sgva series
(viii) gva series
roof and landscape joints
(i) rnpj series
(ii) rmf series
(iii) rts series
(iv) rcbs series

We are offering mild steel angles.
25 x 25mm upto 250 x 250mm
any thickness from 3mm to 25 mm and more

only power grid approved steel rollers for complete range of mt/ht angles from 25x25x3 to 250x250x35
exclusive trading unit for all sizes of ms/ht plates/ sheets and tmt bars.

We are offering broad flange beams.
section kg/mtr
116 x 100 mm 23
152 x 152 mm 37.1
150 x 150 mm 36.4
200 x 200 mm 40.

We are offernig mild steel beams.
section kg/mtr
100 x 50 mm 8.9
150 x 75 mm 15
200 x 100 mm 25.4
300 x 140 mm 46.1
400 x 140 mm 61.6
500 x 180 mm 86.9
125 x 70 mm 13.4
175 x 85 mm 19.5
250 x 125 mm 37.3
350 x 140 mm 52.4
450 x 150 mm 72.4
600 x 210 mm 124.

Specifications

Types Of Bridge Expansion Joints we Design, Manufacture, Supply, Replace, Supervision & Installation. Approved by MORTH, RDSO, NHAI

Specifications

45 x 30 mm to 3 to 6 mm
75 x 50 mm to 6 to 10 mm
90 x 60 mm to 6 to 12 mm
100 x 75mm 6 to 12 mm
125 x 75mm 5 to 10mm

Specifications

Section Kg/mtr
116 x 100 mm 2

Specifications

Deevinaas Portable Bar cutter and benders have an excellent cutting & bending capacity owing to a strong hydraulic and less in w

Specifications

25 x 25mm upto 250 x 250mm
Any thickness from 3mm to 25 mm and more

Specifications

Deevin group offers an architectural line of seismic, thermal and waterproof expansion joint systems meeting the aesthetic demand