Finpower manufactures customized and standard air handling unit starting from 5TR capacity. Air handling unit is used to provide ventilation, heating, cooling, dehumidification and air distribution to a space.

• SK50T SERIES.
• Fresh air handling units are constructed in Thermal break profile.
• High Quality CFC free injected polyutherane foam. Rock wool /fibre glass insulation can be provided as required.
• Floor mounted or ceiling suspended type.
• High efficiency backward curved fans tested and certified by AMCA in accordance to AMCA 210 for air performance and AMCA 300for sound performance and FEG certified fans
• Cooling coils of copper finsand copper tubes / anti corrosive coating. Stainless steel casing etc can be provided for coastal applications.
• With EC motors for special applications e.g. LEED, Green building concepts.
• UL Certified Electric heaters.
• Stainless Steel drain pan as per ASHRAE 62.2.
• Suitable for Outdoor Applications.
• Can be customized according to the site requirement.
• VFD /Starter control panel can be provided.
• Airflow Available from 1700 CMH to 68000 CMH.

• SK-25-ERU SERIES
• Compact design and low noise unit.
• Heat recovery wheel for recovery
• Cross plate type heat exchanger
• Heat recovery heat pipe
• Direct driven single phase motors
• UL Certified filters
• Low height design

Fan Coil Unit or FCU is a device used in a building to heat or cool a specific space. It is essentially made up of a motor with a fan, a heating or cooling coil connected to the buildings central hot water and cold water system, and valve with a controller. In simple terms, Fan Coil Unit is a heat exchanger where the fan and motor brings air, which is a medium of transfer, to the copper coil. The coil is either having hotter or colder water so transfers the heat to the flowing air.

Our fan coil units are now AHRI certified

Standard Features of Fan Coil Unit

• Airflow range from 400 Cfm to 3000 Cfm.
• ESP range from 20 Pa 250 Pa.
• Coil number of rows from 2 to 6 rows.
• Medium water.
• District cooling or chiller.
• 2 pipe system.
• GI casing well insulated and robust construction.
• Forward curved DIDW fan with statically and dynamically balanced impeller to handle high static with low noise.
• 3 speed permanent split capacitor run, thermally protected motor.
• Maintenance free permanent lubricated ball bearing.
• AC 220 240 volt, 50 Hz, single phase, IP 20, Class B insulated motors with anti vibration rubber mounts.
• Electronically Commutated ( EC) motors, 50/60 Hz, Class B insulation, IP 20, 3 Speed or Step less control as an option for high efficiency can be provided
• All motors are wired to a junction box for easy connection. Wiring diagram is pasted beside to identify neutral.
• Return air plenum and filter.
• Access panel provided below plenum for access to motor and fan.
• Aluminium fins are mechanically bonded over 3/8 copper tubes for higher.
• Copper headers with air vent and drain plug.
• Low height for fitting in ceiling voids
• Die cast powder coated drain pan with foam insulation.
• Coarse filter with upto 65% efficiency.

Optional Features

• As per IAQ requirements we can provide higher grade filters for our Fan coil Unit. However performance need to be checked with us as a consequence.
• Split filters can be provided for easy maintenance
• Bottom/ Side removable filters can be provided when return is ducted .
• Bottom return plenum can also be provided.
• Cutouts can be provided on the plenum sides for treated fresh air entry mixing.
• Copper fins can be provided for highly corrosive environment.
• Aluminium fins with coating or fins produced by using coated aluminum fin stock can be provided.
• Class F insulated motors and higher IP ratings available.
• Stainless steel drain pans with foam insulation.
• Extended drain pan and auxiliary drain pans.
• 2 way / 3 way valves with actuators.
• Thermostat

• SK-25-ECO SERIES
• Odour and smoke removal system
• Backward curve type non Overloading fans
• UL certified Filters as per EN 1822 standard
• Activated carbon type refillable filter tray Type
• Suitable for Kitchen exhaust and laboratory exhaust
• With control panel as an option

Option

• Electrostatic Filters
• UL /CE certified UV lamps
• UL rated Fire dampers
• Motor outside the air stream

• SK-25-VENT
• Compact design and low noise
• Centrifugal fan are AMCA 210 , 300 and FEG certified
• Standard TEFC motor with IP 55 and class F insulation
• Option of Filters , Fire damper , auto change over panel can be provided

Fin power coils have wide range of coils for almost all heat transfer applications. The entire range of 3/8, 1/2, 5/8 coils are manufactured at our fully equipped factory at Dubai industrial park, Jebel Ali.

AIR HANDLING UNIT (AHU) COILS

• CHILLED WATER COILS
• HOT WATER COILS
• DIRECT EXPANSION (DX)COILS

FAN COIL UNIT (FCU) COILS

• CHILLED WATER COILS
• HOT WATER COILS
• DIRECT EXPANSION (DX)COILS

TYPE OF COPPER TUBES

• 3/8 OD Plain
• 1/2 OD Plain
• 5/8 OD Plain

TYPE OF FINS

• Aluminium fins
• Hydrophilic or Pre-Coated Aluminium fins
• Copper fins

TYPE OF COIL COATINGS

• Heresite coating
• E-Kote
• Special coating on request

Finpower & fin coils specializes in manufacturing of Air-conditioning equipment manufacturing and Kitchen ventilation system with state of art manufacturing facility located in Baikampadi Industrial Area, Mangalore. Finpower is committed to provide quality HVAC solution for Commercial, Residential and special application projects with the backup of strong engineering team to serve diverse design challenges. Finpower is committed toward environment which provides HVAC engineering solutions with assist in saving energy and reducing the carbon foot prints and abets customer in operational savings.

Finpower condensing unit is best inquality and energy efficiency available in market today. Condensing unit is available with single or dual Hermetic sealed scroll compressors and they can be used with multiple refrigerants, such as R22, R410A and R407C.

Salient Features

Design for ambient of 85 Deg F to 115 Deg F and SST of 35 Deg F to 50 Deg F

Refrigerant: R22, R410A and R407C

CABINETS:Cabinets are constructed of heavily zinc coated galvanized steel .Chemically cleaned and phosphatized to bond the specially formulated corrosion inhibiting, polyester powder coating.

CONDENSER COIL:Condenser Coil are formed of seamless smooth surface or inner grooved copper tubing with mechanically bonded aluminum alloy plate fin slit type

COMPRESSOR:Single or Dual Hermetic sealed scroll compressors are applied together with internal compressor motor protection.

Condenser Fan Motor:Permanently split capacitor motor with permanently lubricated ball bearing and internal thermally protector.

Standard accessories:

• High pressure protection
• Low pressure protection
• Magnetic contactor
• Time delay relay
• 220V /240V Control Circuit
• Crankcase heater for higher capacity unit

Optional Features

• Expansion valve
• Slight glass
• Filter drier
• Solenoid valve
• Shut off Valve
• Copper fins
• Phase Protector

Fresh air handling unit is used to circulate 100% fresh air to a closed space. Fresh air handling unit treat the fresh air by cooling/heating and pass on to the room.

A duct heater is a device used for sensible heating or re heating purposes. Both application lead to increasing temperature of passing air, Sensible heating is done for purely increasing temperature of cold air and to heat up the space. Re-heating is done to heat up sub-cooled dehumidified air so that it does not chill the space while keeping the air dry. Designed and assembled under strict quality control to withstand the severe climatic conditions in the Arabian Gulf area.The assembled capacities range from 0.25 KW to 110 KW.They are custom built to the site requirement.

The thermal wheel is used to recover the energy from the exhaust air and subsequently bring down the overall cooling load.The thermal wheels are air to air rotary heat exchanger and can recover energy up to 80% without spoiling the IAQ. The heat wheel can recover both the sensible as well as latent heat thus reducing the load on the main cooling coil by around 30 % Two basic types of Wheels are available. Sensible heat recovery wheel for sensible heat recovery only Enthalpy heat recovery wheel for Sensible and latent recovery The thermal wheel is a revolving cylinder divided into a number of parallel flutes.

SK50T Series are Horizontal Floor mounted Fresh Air handling units capable of handling the air volume from 1700 CMH to 60000 CMH and handling external static pressure of up to 1000 pa. The casing consist of 50 mm thick profile with Thermal bridge which ensures that no condensation takes place on the surface of AHU The panels are of 50 mm thick insulated with CFC free PUF with uniform density of 40 kgm3 The unit consists of following components

SK-25-ERU SERIESCompact design and low noise unit.Heat recovery wheel for recoveryCross plate type heat exchangerHeat recovery heat pipeDirect driven single phase motorsUL Certified filtersLow height design

Fin power coils have wide range of coils for almost all heat transfer applications. The entire range of 38, 12, 58 coils are manufactured at our fully equipped factory at Dubai industrial park, Jebel Ali. AIR HANDLING UNIT (AHU) COILS CHILLED WATER COILSHOT WATER COILSDIRECT EXPANSION (DX)COILS FAN COIL UNIT (FCU) COILS CHILLED WATER COILSHOT WATER COILSDIRECT EXPANSION (DX)COILS

Finpower manufactures customized and standard air handling unit starting from 5TR capacity. Air handling unit is used to provide ventilation, heating, cooling, dehumidification and air distribution to a space.

• SK50T SERIES.
• Fresh air handling units are constructed in Thermal break profile.
• High Quality CFC free injected polyutherane foam. Rock wool /fibre glass insulation can be provided as required.
• Floor mounted or ceiling suspended type.
• High efficiency backward curved fans tested and certified by AMCA in accordance to AMCA 210 for air performance and AMCA 300for sound performance and FEG certified fans
• Cooling coils of copper finsand copper tubes / anti corrosive coating. Stainless steel casing etc can be provided for coastal applications.
• With EC motors for special applications e.g. LEED, Green building concepts.
• UL Certified Electric heaters.
• Stainless Steel drain pan as per ASHRAE 62.2.
• Suitable for Outdoor Applications.
• Can be customized according to the site requirement.
• VFD /Starter control panel can be provided.
• Airflow Available from 1700 CMH to 68000 CMH.

• SK-25-ERU SERIES
• Compact design and low noise unit.
• Heat recovery wheel for recovery
• Cross plate type heat exchanger
• Heat recovery heat pipe
• Direct driven single phase motors
• UL Certified filters
• Low height design

Fan Coil Unit or FCU is a device used in a building to heat or cool a specific space. It is essentially made up of a motor with a fan, a heating or cooling coil connected to the buildings central hot water and cold water system, and valve with a controller. In simple terms, Fan Coil Unit is a heat exchanger where the fan and motor brings air, which is a medium of transfer, to the copper coil. The coil is either having hotter or colder water so transfers the heat to the flowing air.

Our fan coil units are now AHRI certified

Standard Features of Fan Coil Unit

• Airflow range from 400 Cfm to 3000 Cfm.
• ESP range from 20 Pa 250 Pa.
• Coil number of rows from 2 to 6 rows.
• Medium water.
• District cooling or chiller.
• 2 pipe system.
• GI casing well insulated and robust construction.
• Forward curved DIDW fan with statically and dynamically balanced impeller to handle high static with low noise.
• 3 speed permanent split capacitor run, thermally protected motor.
• Maintenance free permanent lubricated ball bearing.
• AC 220 240 volt, 50 Hz, single phase, IP 20, Class B insulated motors with anti vibration rubber mounts.
• Electronically Commutated ( EC) motors, 50/60 Hz, Class B insulation, IP 20, 3 Speed or Step less control as an option for high efficiency can be provided
• All motors are wired to a junction box for easy connection. Wiring diagram is pasted beside to identify neutral.
• Return air plenum and filter.
• Access panel provided below plenum for access to motor and fan.
• Aluminium fins are mechanically bonded over 3/8 copper tubes for higher.
• Copper headers with air vent and drain plug.
• Low height for fitting in ceiling voids
• Die cast powder coated drain pan with foam insulation.
• Coarse filter with upto 65% efficiency.

Optional Features

• As per IAQ requirements we can provide higher grade filters for our Fan coil Unit. However performance need to be checked with us as a consequence.
• Split filters can be provided for easy maintenance
• Bottom/ Side removable filters can be provided when return is ducted .
• Bottom return plenum can also be provided.
• Cutouts can be provided on the plenum sides for treated fresh air entry mixing.
• Copper fins can be provided for highly corrosive environment.
• Aluminium fins with coating or fins produced by using coated aluminum fin stock can be provided.
• Class F insulated motors and higher IP ratings available.
• Stainless steel drain pans with foam insulation.
• Extended drain pan and auxiliary drain pans.
• 2 way / 3 way valves with actuators.
• Thermostat

• SK-25-ECO SERIES
• Odour and smoke removal system
• Backward curve type non Overloading fans
• UL certified Filters as per EN 1822 standard
• Activated carbon type refillable filter tray Type
• Suitable for Kitchen exhaust and laboratory exhaust
• With control panel as an option

Option

• Electrostatic Filters
• UL /CE certified UV lamps
• UL rated Fire dampers
• Motor outside the air stream

• SK-25-VENT
• Compact design and low noise
• Centrifugal fan are AMCA 210 , 300 and FEG certified
• Standard TEFC motor with IP 55 and class F insulation
• Option of Filters , Fire damper , auto change over panel can be provided

Fin power coils have wide range of coils for almost all heat transfer applications. The entire range of 3/8, 1/2, 5/8 coils are manufactured at our fully equipped factory at Dubai industrial park, Jebel Ali.

AIR HANDLING UNIT (AHU) COILS

• CHILLED WATER COILS
• HOT WATER COILS
• DIRECT EXPANSION (DX)COILS

FAN COIL UNIT (FCU) COILS

• CHILLED WATER COILS
• HOT WATER COILS
• DIRECT EXPANSION (DX)COILS

TYPE OF COPPER TUBES

• 3/8 OD Plain
• 1/2 OD Plain
• 5/8 OD Plain

TYPE OF FINS

• Aluminium fins
• Hydrophilic or Pre-Coated Aluminium fins
• Copper fins

TYPE OF COIL COATINGS

• Heresite coating
• E-Kote
• Special coating on request

Finpower & fin coils specializes in manufacturing of Air-conditioning equipment manufacturing and Kitchen ventilation system with state of art manufacturing facility located in Baikampadi Industrial Area, Mangalore. Finpower is committed to provide quality HVAC solution for Commercial, Residential and special application projects with the backup of strong engineering team to serve diverse design challenges. Finpower is committed toward environment which provides HVAC engineering solutions with assist in saving energy and reducing the carbon foot prints and abets customer in operational savings.

Finpower condensing unit is best inquality and energy efficiency available in market today. Condensing unit is available with single or dual Hermetic sealed scroll compressors and they can be used with multiple refrigerants, such as R22, R410A and R407C.

Salient Features

Design for ambient of 85 Deg F to 115 Deg F and SST of 35 Deg F to 50 Deg F

Refrigerant: R22, R410A and R407C

CABINETS:Cabinets are constructed of heavily zinc coated galvanized steel .Chemically cleaned and phosphatized to bond the specially formulated corrosion inhibiting, polyester powder coating.

CONDENSER COIL:Condenser Coil are formed of seamless smooth surface or inner grooved copper tubing with mechanically bonded aluminum alloy plate fin slit type

COMPRESSOR:Single or Dual Hermetic sealed scroll compressors are applied together with internal compressor motor protection.

Condenser Fan Motor:Permanently split capacitor motor with permanently lubricated ball bearing and internal thermally protector.

Standard accessories:

• High pressure protection
• Low pressure protection
• Magnetic contactor
• Time delay relay
• 220V /240V Control Circuit
• Crankcase heater for higher capacity unit

Optional Features

• Expansion valve
• Slight glass
• Filter drier
• Solenoid valve
• Shut off Valve
• Copper fins
• Phase Protector

Fresh air handling unit is used to circulate 100% fresh air to a closed space. Fresh air handling unit treat the fresh air by cooling/heating and pass on to the room.

A duct heater is a device used for sensible heating or re heating purposes. Both application lead to increasing temperature of passing air, Sensible heating is done for purely increasing temperature of cold air and to heat up the space. Re-heating is done to heat up sub-cooled dehumidified air so that it does not chill the space while keeping the air dry. Designed and assembled under strict quality control to withstand the severe climatic conditions in the Arabian Gulf area.The assembled capacities range from 0.25 KW to 110 KW.They are custom built to the site requirement.

The thermal wheel is used to recover the energy from the exhaust air and subsequently bring down the overall cooling load.The thermal wheels are air to air rotary heat exchanger and can recover energy up to 80% without spoiling the IAQ. The heat wheel can recover both the sensible as well as latent heat thus reducing the load on the main cooling coil by around 30 % Two basic types of Wheels are available. Sensible heat recovery wheel for sensible heat recovery only Enthalpy heat recovery wheel for Sensible and latent recovery The thermal wheel is a revolving cylinder divided into a number of parallel flutes.

SK50T Series are Horizontal Floor mounted Fresh Air handling units capable of handling the air volume from 1700 CMH to 60000 CMH and handling external static pressure of up to 1000 pa. The casing consist of 50 mm thick profile with Thermal bridge which ensures that no condensation takes place on the surface of AHU The panels are of 50 mm thick insulated with CFC free PUF with uniform density of 40 kgm3 The unit consists of following components

SK-25-ERU SERIESCompact design and low noise unit.Heat recovery wheel for recoveryCross plate type heat exchangerHeat recovery heat pipeDirect driven single phase motorsUL Certified filtersLow height design

Fin power coils have wide range of coils for almost all heat transfer applications. The entire range of 38, 12, 58 coils are manufactured at our fully equipped factory at Dubai industrial park, Jebel Ali. AIR HANDLING UNIT (AHU) COILS CHILLED WATER COILSHOT WATER COILSDIRECT EXPANSION (DX)COILS FAN COIL UNIT (FCU) COILS CHILLED WATER COILSHOT WATER COILSDIRECT EXPANSION (DX)COILS