Material: Almost all media O-ring: NBR/FKM
Color: Green/Brown O-ring: Black/Brown

High static and dynamic sealing effect Low friction, high efficiency
Stick-slip free starting, no sticking Easy installation

It excels at sealing irregular surfaces and maintaining a tight seal under demanding processing and system conditions.

This material is recommended for gaskets used in flange sealing duties in steel pipes and equipment for pharmaceutical, food and beverage processing.

Suitable for pharmaceutical, food and beverage processing duties.Resistant to creep and cold flow.Maintains a reliable, durable seal.Dimensionally stable.Conforms easily - seals irregular flanges.Retains tightness - minimum re-torque.Documented lot traceability.

USP Class Vl Biocompatibility.US food contact compliance: FDA 21 CFR 174.5(d).EU food contact compliance:

Resistant to all media in the range pH 0-14, excludingalkali metals and elemental fluorine, particularlyat elevated temperatures.

Temperature stability: expanded PTFE is stable in temperature ranges typically found in food and pharmaceutical applications: -100C to +270C with excursions to +315C (-148F to +518F with excursions to +600F).

Standard thicknesses: 1.5mm & 3.0mm. Standard sheet size: 1524mm x 1524mm.

gasket are available in 1.5 mm, 2 mm & 3 mm, 4 mm, 5 mm thick. Gaskets are manufactured to suite different flange standard like; E/F table, ANSIB-16.5-150, 300 & 600. Class flange, DIN standard flanges from 1/2 NB (15NB) to 28 NB. PTFE gaskets are available in raise face size & full face size. PTFE gaskets are also available as per client drawing specification.

Spring Energised seals are single acting seals which are used for dynamic and static applications.They are effective in a wide range of applications. They are chosen when higher resistance to chemical media is required, if the seal is required to operate in extremes of temperature and where good extrusion and compression characteristics are needed.

1. Application specific U-shaped seal profile
2. Spring geometry suited to the particular application
3. Proven high-performance polymers

Standard products are available from 2 mm up to 2500 mm (8' 2") in diameter along with custom Manufactured intermediate sizes, inch (imperial) sizes or special geometries.

All seals have the same operating principle and differ only in their profile form and type of metallic spring used. The spring supplies the load required for sealing at low pressures. The "U" shaped jacket allows fluid pressure to energize the sealing lips, so total sealing pressure rises with increasing operating pressure Spring Force.

The different types of seal combined with the properties of materials offer design engineers a wide range of solutions to a large number of applications. The most important characteristics of Spring Energised Seals are listed below:
Very low coefficient of friction
Good dynamic and static sealing
Capable of sealing at high speeds up to 15 m/s (49 ft/sec)
Almost universal chemical compatibility
Operating temperature of -253 C up to +300 C (423 F to 572 F)
Very good thermal resistance
Permanent elasticity unaffected by contact with chemicals
Good ageing characteristics
Low compression set
Capable of withstanding high pressures above 200Mpa (2000 bar, 29000 psi) when using Back-up Rings
Very good dry-running properties

Spring Energised seals offer major benefits in the design of components such as hydraulic and pneumatic cylinders, in all industries.

These include:
Excellent leak tightness
High resistance to wear
No extrusion into gaps
Withstanding aggressive and abrasive process media
Very good temperature capabilities
Low friction
Compact form
Simple installation

These seals are available in a range of geometries and designs that allow the optimum profile to be selected for each application. They can be produced from a wide range of PTFE based compounds. These are specially formulated for sealing elements and offer superior characteristics specifically matched to the demands of our customers. When required, Spring Energised seals can also be manufactured in polyethylene based material. To choose the best seal for your application, you must first decide the functional parameters. It is also important to consider the quality of the mating surface, which has a significant effect on the function and service life of the sealing system.

1 - Could be provided by kilogram or meter
2 - High abrasion resistance, wide range of application temperatures
3 - Low friction, high efficiency
4 - Stick-slip free starting, no sticking
5 - Easy installation

We are one of the well-reputed and established manufacturers and suppliers of an high quality array of PTFE Compressor Parts. These are manufactured using superior quality material which ensures durability.The filled Teflon (PTFE) that we process are suitable for serving nearly every identifiable market at both the OEM and after-market levels. These can also beemployed by plastics distributors and machine shops thatserve OEM's. The Parts display exemplary performancecharacteristics and have a long service life even undercritical conditions.

1. 
   

   Piston Rings

   
   


2. 
   

   Wearing Rings

   
   


3. 
   

   Rider Rings

   
   


4. 
   

   Seal Rings

   
   


5. 
   

   Bearing Rings

   
   


6. 
   

   Gland Packing

   
   


7. 
   

   Shaft Bearing

   
   

PTFE Rod is often chosen to produce bearings because of its very low friction and also for its free running ability. Because of its ability to conform to shape otherwise known as flow, PTFE Rod is used for seals in valves, this is because it can conform to shape and create a high specification valve seal.

PTFE Rod can easily be machined but due to the surface softness, care must be taken in lathe jaws or high compressive loads, which may cause distortion

Another important element to remember regarding PTFE Rod is the coefficient of expansion due to heat changes; this can be uneven with PTFE and may cause distortion in components.

We are among the leading manufacturers, suppliers and exporters of wide range of high qualityPTFE Ball Valve Seats. These products undergo various quality assurance procedures at each level of their productions, to ensure high standards of quality and safety. These products are chemically inert to attack by most chemicals. These products are available in standard sizes that best suits the requirement of our valuable customers. These products are available in various grades for our valuable customers. We believe in effective and timely delivery of these products once ordered, owing to vast network of our dedicated employees.

PTFE seats are providing consistent perfomance with min.maintance

PTFE Insulated Sleeve application is for high temperature or high frequencies or both. PTFE Sleeve and teflon sleeve possesses excellent electrical properties, which remain practically constant over a wide range of frequencies, temperature (-600 to +2600 C) and humidities andhas a very low loss factor.

Resistance to fire

Resistance to Chemicals

Corona resistance

Non-flammable

The widest product range in the sector Due to their elastomer sealing lip, standard radial shaft seals have only a limited application range with respect to pressure , temperature and media loads.
High performans sealing lips made from modified PTFE , cause very low friction , thanks to their stick-slip-free running , suffer little wear and tear, reducing the heat development and permitting higher peripheral speeds.

1 - Low friction seal material
2 - Low and high temperature range (-60 to +260 C
3 - High pressure capability (up to 25 bar )
4 - High speed ability ( 40 m/s )
5 - Outstanding resistance to chemical media
6 - Fits Standard oil seal installation groove.

Given the many different needs involved in practical applications, TOKEZ offers users many different product versions , ranging from standard one lip , ready to-install , available from stock; right through to customized special designs.

Sealing Lip

1 - Standard material with exceptional wear and friction characteristics.For lubricated or dry running. Carbon filled , Black colour.
2 - Special material for all lubricating and non-lubricating fluids and suitable for soft counter-surfaces. Moly filled , Grey colour.
3 - Special application such as food stuff , pharmaceutical and chemical industries. Colour : Tan to dark brown.

Case Material :Gasket Elastomer

Standard material :Fluoroelastomer (-25 to +200 C)

1 - Centrifuge machinery
2 - Pumps
3 - Mixers
4 - Separators
5 - Agitators
6 - Spiral conveyors.
7 - Rotary lead-throughs

Bellows are specially designed from virgin PTFE and is contour molded. This manufacturing method guarantees an excellent structure of the material; symptoms of ageing are practically excluded.

Very long term durability and low maintenance cost are assured. The bellows can be used up to 200oC. Bellows serve for compensation of vibration, thermal strain expansion and Axial & Redial motion.

The sealing surfaces are covered end plates and individually boxed for protection against mechanical damage. Limit bolts are preset to prevent over extension during operation.

These Bellows are meant for resisting highly corrosive plants and piping for aggressive Medias. These Bellows are installed in PTFE Lined Carbon Steel Piping and equipment without additional gaskets. For use with piping and equipment made of glass, enamels and ceramics we recommend PTFE Gaskets, offered as accessory.

Bellows are manufacturing in different sizes from NB 25mm to NB 300mm. The standard length is 67.5mm long.

Quite simply Turcite is PTFE impregnated with fillers and additives that serve to enhance the wear properties of the material.

It is used, most often in a sheet form, in thicknesses ranging from 0.5mm (0.02) to 4mm (0.16), although in some applications, it is also used as a bush and in more rare applications it is used as a thick plate.

Being based on PTFE, the material cannot be extruded like a normal plastic sheet and instead needs to be skived the process most commonly used to make thin PTFE sheets.

Also, the material will not easily adhere to other surfaces another feature resulting from its PTFE base.

Therefore a chemical etching is required on one surface of the material, so the sheet can be bonded to other articles.

1. 
   

   Planers,

   
   


2. 
   

   milling machines

   
   


3. 
   

   SPMs

   
   


4. 
   

   Sharper's, horizontal & vertical boring machines,

   
   


5. 
   

   hydraulic & pneumatic power presses,

   
   


6. 
   

   press brakes,

   
   


7. 
   

   all types of grinders,

   
   


8. 
   

   radial drills,

   
   


9. 
   

   automatic screw machines,

   
   


10. 
    

    gear hobbers,

    
    


11. 
    

    gear shapers.

    
    

OurPTFE Ballsare perfectly used, where metals or alloys cannot be used. PTFEPlastic Balls are highly functional in self-lubrication conditions such as ballbearings. Today, we are counted among the key PTFE Balls Manufacturers andSuppliers in India. Solid PTFE Balls are available in size range of 6mm to 10mm oraccording to the specifications of our customers.

The PTFE ball is a unique product. It has many advantages in applications where metals or alloys can not be used. These advantages are Broad operatingtemperature (-400oF to +500oF), Chemical inertness to most corrosive liquids orgases extremely low coefficient of friction. PTFE balls are highly functional in selflubricating conditions such as ball bearings. In the fluid handling industry PTFEballs are used in ball valves that have contact with extremely corrosive liquids.PTFE ball has reduced maintenance costs and man hours in the field by eliminating the replacement of valve components subjected to corrosive environments.

Balls are available in size from 6mm to 150mm. But it can also be made in any specifications.