Our Products
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Additional Information:
Delivery Time : 6 to 8 weeks
Compact automatic three stage flow, max efficiency. Applicable on both one or two wrenches simultaneously.
Aluminum oil tank with oil gauge and thermometer.
Have inbuilt high pressure gauge.
Infinitely variable pressure adjustment between 40 to 700 bar.
Hour Meter available on request to calculate number of working hours of the pump
Temperature sensors available on request to indicate temperature at different ranges
Automatic Shutoff available on request to shutoff pump in case of non cycling
With the high efficiency radiator the pump can work 24 direct hours Can change the motor to fit the different current around the world. You could change the export components(FP-4), drive four wrenches at the same time.
Light weight, Compact design for easy portability.
Enable to maximize the effciency of work.
Various models can be used with the most of hydraulic tools.
Can be used anywhere and under any condition with oil-tight tank.
220V Single phase is standard.
Can be used for every electric tools.
Light Weight , Compact Design for easy Portability.
Can be used with most Hydraulic Tools.
Model |
Flow rate (I/min) |
Pressure rating (kg/cm2) |
Reservoir capacity (liter) |
Weight (kg) |
||
KUP-35RH |
LOW | HIGH | LOW | HIGH | 0.8 | 7.5 |
2.0 | 0.2 | 10 | 700 | 1.6 | 8.5 |
UNIQUE Bearing Fitting Tool Kit Comprises of 36 or 33 Impact Rings made out of Super Tough Light Weight Impact Resistant Ultra High Molecular Polyethylene Rings
Made to fit diverse combination of Impact rings and Impact Sleeves, 3 numbers of Aluminium Impact Sleeve and A Nylon Mallet in a suitable carrying case.
With the above assembly one can mount over 200 types and sizes from 10 mm to 50 mm of Bearings with precision and accuracy.
Each Sleeve can accommodate about 200 mm length projecting shaft.
Selection Chart is provided in each kit to identify easy mounting.
The kit contains 36 or 33 (as required)impact rings of different sizes as perstandard sizes of bearings, 03 impact sleeves and a dead-blow hammerpacket in lightweight carrying case.
Impact rings are marked for clear visual identification of the ringssize and easy selection.
Impact rings and sleeves are made of high impact resistant materialfor longevity.
Dead-blow hammer is of nylon double side head
Carry Case
The easy and convenient and economical way of mountingmedium size bearing is by using UNIQUESPIRALELECTRICAL HEATER. Even today we find quiet a few outdatedmethods being followed and their shortcomings are beinghigh lighted over here. Use of naked flame for e.g. is risky anddoes not ensure uniform heating. If an oil bath is used it may resultin dirt entering the bearing. Dripping of hot oil is not onlyhazardous but also messy. In fact they are against todays ecologicalnormsUse of hammers or other pressing forces may damage the bearingand cut short its life. Thus the ideal solution for medium sizebearing is to heat and mount by UNIQUESPIRAL ELECTRICALHEATER. They are eco friendly.
EASY TO USE:Connect the unit to the suitable electrical pointMount the suitable coil at the center point. And switch on the unit.Select the required temperature.Place the bearing or the heating component on the centering support.Press the start button.The spiral heater does the rest and will automatically switch off when the desired temperature is reached.Removethe heated job by the special hand gloves provided with unit and mount the same in placeFEATURES :The UNIQUESPIRAL HEATER is supplied with heating coils of 1 KW and 75 KW. 1 KW coil is used for heating bearingof bore size 55 mm to 100 mm. The 1.75 KW coil is used for heating the bearings of bore size 100 to 150 mm . The heating coilscan be easily changed since they are just of plug in type. The unit ensures uniform heating through the centering support Thetemperature control sensor is in contact with the inner ring of the bearing. Once the set temperature is reached the same can beseen on the display panel and one can hear the audio alarm signaling the job has been heated. The unit is provided with a microswitch which switches off the current once the job is heated to the set temperature. This is an additional safety feature provided.Apart form bearing couplings, cams rings etc. can also be heated to an accuracy of +I- 2 deg C
Multigrade Cylinder Design, Increase the Tension Length Strong capacity with small outside diameter, it is suit for the operation at narrow space.
700-1500bar operation pressure Spring return protect for the stroke over the maximum value, it is suit for operation frequently.
Operate by Super High Pressure Hand Pumps and Electrical Pump
Technical Data |
Model | ||
HTE36-00 | HTE42-00 | HTE42A-00 | |
Maximum Operation Pressure | 1035bar | 1050bar | 1305bar |
Maximum Output Capacity | 800KN | 1039KN | 800KN |
Maximum Stroke | 10mm | 10mm | 10mm |
Cylinder Effective Area | 6126mm2 | 9896mm2 | 6126mm2 |
Quantity of Cylinder Step | 3 | 3 | 3 |
Outside Diameter | 100mm | 105mm | 111mm |
Bolt Size | |
Electric Hydraulic Rail Road Axle Journal Cartridge Tapered Roller Bearing Puller / Installer with Hydraulic Power Pack Unit are suitable for removing and installing Cartridge tapered roller bearing from axle.
Technical Specification:
1. Stroke Horizontal : 400 mm ( approx )
2. Capacity:
(a) For Bearing Installation (mounting) : Min. 70 Tons
(b) For Bearing dismounting : Min. 100 Tons
3. Speed:
(a) Speed of advancement of ram in idle condition : 28.3 cm/min (approx)i.e., without load
(b) Speed of dismounting the bearing : 7.4 cm/min (approx)
(c) Speed of mounting the bearing : 10.5 cm/min (approx)
4. Type of Cylinder: Single Hydraulic Double Acting Cylinder
5. Hydraulic Pressure: 500 Bars (Max.)
6. Other Power pack details
(a) Suction & return line filter
(b) Oil reservoir capacity: 40 Litres ( approx )
(c) Control Valve
(i) Direction Valve: Three position four-way hand-operated open centre valve.
(ii) Other control valves :
(a) Built in pressure relief valve for safety maximum pressure 500 Bars
(b) Field adjustable pressure relief valve maximum pressure 500 Bars
7. Motor details :
(a) Horse Power 5 HP (or suitable) capacity with Motor Starter and Motor Protection Circuit Barker ( MPCB )
(b) Phase Three Phase
(c) Voltage 415 Volts 10%, 50 Hz.
8. Height from floor tocenterof installation table from 400 mm minimum to 600 mm Maximum: Hydraulic height adjustment arrangement is provided.
9. Extractor / puller and power pack: Mounted on trolley.
10. The trolley ismounted on wheels to make it mobile and is easily maneuverable.
11. All parts with critical application, such as pulling shoe, inserts, adapters is made of alloy steel to ensure long life and minimum wear.
12. The equipment is of such design which will enable in faster and simpler way of pulling / installing operations.
13. The use of puller / installer will consume an absolute minimum time and effort.
14. The machine is capable of giving the out turn of minimum 30 wheel sets for mounting / dismounting, during a shift of 08 hours under ideal condition.
15. We willsupply the accessories like complete set of pulling and pushing adaptors, guide tub, yoke plates, etc if needed extra.
16. Hydraulic and electric components used is of standard and quality makes. Machine is supplied with necessary hydraulic oil fill and 5 M electric supply lead with plug and socket.
17. The equipment iscompletely portable for easy and convenience positioning out of the way storage and can be conveniently operated by one operator
18. The construction of equipment is designed to enable faster and simpler way of pulling / installing operations by two operators