Write a Review
Our Products
Our Complete range of products are Silicone Heat Sink Compound, Dpdt Switches, DUMMY WHEEL, Sensor Module and LIGHT INTENSITY SENSOR MODULE.
Operating Voltage: 7 to 12V DC. 2. Low power consumption. 3. On board 5V regulator. 4. Direct connection. 5. 4 PIN header interface for output 6. LED Indicators for POWER & DATA output.
A rotary encoder has a fixed number of positions per revolution. These positions are easily felt as small clicks you turn the encoder.
On one side of the switch there are three pins. They are normally referred to as A, B and C. In the case of the KY-040, they are oriented as shown.
Inside the encoder there are two switches. Once switch connects pin A to pin C and the other switch connects pin B to C.
Can detect surrounding environment of the humidity and temperatureDHT11 sensor adoptsHumidity measurement range: 20% 95%Humidity measurement error: 5%Temperature measurement range: 050Temperature measurement error: 2 Operating voltage:3.3 V5 VOutput form:digitalHas fixed bolt hole and easy installation
This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier to use version of the simple foto resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. With the BH1750 Light Sensor intensity can be directly measured by the luxmeter, without needing to make calculations. The data which is output by this sensor is directly output in Lux (Lx). When objects which are lighted in homogeneous get the 1 lx luminous flux in one square meter , their light intensity is 1lx
The E3D-v6 has been redesigned from the ground up. E3D has invested a lot of time and used all of their experience to design E3Ds latest and greatest HotEnd. If you would like to know more about the design process, check out this blog post.
Print the Widest Range of Materials Possible.
Building on their signature high temperature performance that allows you to print high temperature materials E3D has now focussed on adding increased functionality with soft and flexible filaments. By providing a PTFE liner tube through the hotend that you can extend into your extruder this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments like NinjaFlex, FlexPLA and FlexPolyester. This opens up a huge range of new opportunities for your printer.
High Temperature Performance.
With no PEEK or PTFE in hot regions of the HotEnd you can reach 300C with the supplied thermistor. By swapping a thermistor for a thermocouple (may require additional electronics) you can reach over 400C.
This not only allows you to print extremely high temperature materials like Polycarbonate and Nylons but also eliminates HotEnd meltdown failures associated with PEEK/PTFE designs. Although the latest v6 hotend has a PTFE liner inside the hotend this liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating.
The new Heater Block gives the fastest heat up times and the most responsive temperature control by clamping around the cartridge for maximum thermal contact. The new thermistor placement means you get the most accurate temperature readings with the fastest response. What this means for you the user is that you can go from 20C to 200C in just 65 seconds, temperature control is responsive enough that you can keep the hotend within 0.5C of your set temperature or less with ease.
Ramps is short for reprap Arduino mega pololu shield, it is mainly designed for the purpose of using pololu stepper driven board (similar to 4988 driven board). Ramps can only work when connected to its mother board Mega 2560 and 4988/DRV8825.
RAMPS RepRap Arduino Mega Pololu Shield, or RAMPS for short.
RAMPS RepRap Arduino Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino MEGA with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
Ramps is short for reprap Arduino mega pololu shield, it is mainly designed for the purpose of using pololu stepper driven board (similar to 4988 driven board). Ramps can only work when connected to its mother board Mega 2560 and 4988/DRV8825. Owning to its stability in operation and great compatibility with most 3Dprinter (all reprap-model such as pursa i2 and i3). The combination of Ramps1.4+MEGA2560+A4988/DRV8825 is becoming a mainstream of DIY 3D printer control board.
10mm Linear Rail Shaft Support made of Aluminium and Anodized surface finish, Shaft Support suitable for 10mm Diameter Shaft used in CNC, 3D Printing applications
This is a high quality 2-axis analog joystick module. It comes with a plastic knob which gives an excellent feel during use.
It can be used to sense movements in 2 directions(axes). It also has a inbuilt switch which can be activated by pressing the stick.
The module brings out the odd pin spaced joystick pins to the standard and easy to use 0.1 spaced headers. The joystick has two power pins and 3 output pins. The position of the stick can be known from the voltage at the two output pins A1(Axis 1) and A2(Axis 2). These pins output 0V and Vcc when the stick is at the two extreme positions of an axis. When the stick is at any other intermediary position, the output is between 0V and Vcc corresponding to the position of the stick. The third output pin provides a digital status of the switch(0V when pressed, Vcc when released).e, This makes it easy to interface the module to any microcontroller with ADC with only a few lines of code.
This joystick is perfect for making classy interfaces, robot remotes, airplane remotes, games, etc. It can be used with out development boards with our female to female jumper wires for connections.
Package list:
Ravji Bhai Makwana (IFuture Technology)
29, SHAKUNTAL COMPLEX, NEAR KALADARSHAN CHAR RASTA, NALANDA WATER TANK RD, WAGHODIA ROAD, VADODARA, Gujarat - 390025, India
Share us via
