International Equipments

Kanjurmarg East, Mumbai, Maharashtra

for pipes as per IS 4985 and IS 12235(Part 9) to test the impact strength of the pipes.

Specification:

Height of fall :500mm, 1000mm and 2000mm.
Weight of striker :250 grams, 500 grams and 1000 grams.
Material of striker :S.S
Angle of V block:120.
Release mechanism of striker :Manual.
Paint:Powder coated.

to check the opaqueness ofplastic samples as per IS 4985and IS 12235 (Part 3).

Specification:

Range :0 99.9 % opaque.
Direct display :% opaque.
Paint :Powder coated.
Power :230 Volts, 50Hz, single phase.

as per IS 4984 and IS 4985 to check the creep rupture of pipe when subjected to internal pressure under a specified condition.

Pressure range : 0 100 bar*.
No. of stations : 8 nos.
Pressure input : Through compressed air having pressure upto 5 kg/cm.sq
Pressure output: through hydro-pneumatic pump.
Time range : 0 999.9 hours.
Panel mounting : Trolley with castor wheels.
Paint : Powder coated.
Power : 230 Volts, 50Hz, single phase.

Direct display through MMI :
Set pressure, Actual pressure, Set time, Actual time, Set temperature and Actual temperature.

Graphic display and printout through PC :
In addition to the above values Pressure & Temperature Vs Time graph could be obtained for any station by attaching a printer to the PC.

Specification:

Double Walled well insulated tank with proper insulation for the doors also.Offered capacity: From 200 litres to 5000 litres capacity.
Stainless steel manifolds placed in the walls of the tank having quick release couplings
Inside and out for easy handling of hoses coming from panel outside and going to the pipe
Paint :Powder coated
Power :415 volts , three phase

as per Tappy T 815 standard to determine the coefficients of friction between film to film, film to metal and film to glass.

Specification:

Speed :1.5 to 2.0 / second.Weight of the sled: 750 grams.
Size of sled :4 inch X 2 inch.
Accessories :2 nos. of S.S templates.
Paint :Powder coated.
Power :230 Volts, 50Hz, single phase.

As per ASTM D 1238 & ISO 1133 (Test Method A & B) to check the melt flow rate (MFR) & melt volume rate (MVR) of thermoplastics and compounds with automatic result.

to check the adhesive strength betweentwo samples.

Specification:

Load capacity :Up to 5 kg.*No. of load cell: One.
Cross Travel :Up to 250 mm*
Speed :300 mm/minute.
Direct display :Peak load.
Paint :Powder coated.
Power :230 Volts, 50 Hz, single phase.

Charpy impact tester is manufactured as per ASTM D 6110 and ISO standard. These models are used by injection moulds & engineering plastic manufacturers. Also charpy impact tester has wide importance in testing polypropylene pipe manufacturing industry for testing the PPR pipe.

Notch cutter is a requirement for making notch on charpy impact samples. Thus notch cutter is also supplied along with this equipment. Charpy impact tester and Izod impact tester are those material testing equipment that are used to check the axial impact on molecular structure of material and thus measure the failure of polymers under impact. condition.

Specification:

Capacity :Up to 25.00 Joules.Release angle of pendulum: 150 degree.
Range of four scales :0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules.Minimum resolution on scale: 0.02 Joule, 0.05 Joule, 0.1 Joule, 0.2 Joule and 0.2 Joule respectively.
Paint :Powder coated.
Power :230 Volts, 50Hz, single phase.

Direct display through microcontroller:Impact strength in joules/meter and kg-cm/cm.

Graphic display and printout through PC:Impact energy Vs Angular displacement graph and numeric reports consisting of values for impact strength as per ASTM standard, ISO and IS standard in different units could be obtained by attaching a printer to the PC.

for conditioning of pipes for impact test as per IS 4984 and IS 12235 (Part 9).

Specification:

Size of the working chamber :16 inch X 16 inch X 16 inch*.Material of construction :Inner bath : S.SOuter Body : M.S
Temperature range :Ambient to 0C.
Compressor :CFC free.
Paint :Powder coated.
Power :230 Volts, 50 Hz, single phase.

International equipments developed the first dart impact tester way back in year 1971 as per the ASTM D 1709 and IS 2508 standard. This equipment is mainly designed to check the impact failure weight of film and sheeting by a falling weight impact method.