Other Products / Services #4599873

Turbulent Gas flow & Higher Inlet velocity of the Dust Laden Gas can hamper the performance of the ESP. Upgrade your ESP with IFIs uniquely de-signed Gas Distribution Screens to help you get the best out of your ESP.

The specific collection area of an ESP decides its collection efficiency. Bent, warped, corroded plates hamper the performance. Getting correct profile of the colleting plates is often difficult task. This problem is put to rest by IFI by devising a concept of adaptive weld-mets, which ensures the new collecting plate fits exactly like the original design. The conversion from side to top rapping can fetch up to 33% increase in collection area.

Other Upgrades


IFI offers Design & Installation of Turning vanes also known as Gas Distribution vanes into the Inlet Duct of the ESP. This helps in
Directing the Gas correctly into the ESP.
Reducing Frictional Losses
Increasing the Efficiency of your ESP.

Ionisation Filtration Industries Pune is a leading manufacturer, of various pollution measuring sensors and devices. It has approximately 400 number of installations across India in various type of industries like cement power textile mills etc. As per Central Pollution Control Board (CPCB) State Pollution Control Board (SPCB) guidelines IFI is required to set up a dedicated ServerCloud Services in CPCB premises and later in each of the SPCB premises where the data from various installations will be made available.
IFI has PlantConnect Monitoring Software for all their requirements like collecting real time data of all industries and display at the server, public portal so general public & concerned authorities can view the data, reports, alarms etc.

Diverter Gates manufactured by IFI offer a perfect solution to the diversion of Solid Materials from a single point to two different delivery pointsregulate the amount of flow to various circuits, and to isolate circuit for maintenance. They are ideal for diverting gravity flow of materials. They can be as basic as a single to double diverter with a manual lever to Change blade position from one side to the other, or they can be fully automated devices capable of controlling flow from one or more sources to various points.

The diverter gate can be actuated while material is being conveyed. This allows faster, more efficient changeovers without the need to shut down the system before activating the diverter. Cylinder mounted limit switches can be fitted as optional extras. Flaps for diversion are provided with Spring Steel Tips which offer very high sealing efficiency & durability.

A screw conveyor can be installed at any operating angle. IFI Screw conveyors are designed to operate under harsh conditions and can handle a variety of dry bulk materials such as cement, lime, raw meal, apatite, urea, fly ash, gypsum etc. The screw conveyor is totally enclosed, with no spillage, hardly any dust creation and a very low level of noise.

IFI Butterfly dampers are available for a wide variety of applications in round ductwork, where low-leakage isolation, flow control, or a combination of the two is desired. Varying degrees of isolation can be obtained from 90 to 99.9% depending on the seal arrangement.
Heavy-duty design that is suitable for applications with clean, corrosive, dirty, andor dry environments.
Manufactured in-house under strict quality control procedures. IFIs range of butterfly dampers are best suited in Duct and Ventilation system where flow control and balancing is required.

Double flap valve is continuous material discharge equipment. Double Flap Valve has a two door flap plate which open and close alternatively.
As the material falls on the top plate, during continuous operation the plate opens and discharges the material on the bottom plate. After discharging the material the top plate closes. This ensures that the DFV is sealed to prevent air leakage.
The bottom plate then opens after the top plate is closed and allows material to fall onto onward collecting equipment.
The cycle time is precisely adjusted such that after the bottom plate closes the top plate opens. Thus ensuring continuous air sealing across the DFV. The time for which both flap are in closed condition, is known as dwell time.

Emission Monitor model EM919 is an indigenous product for measuring dust concentration. This device operates on the principle of optical transmissometry, using single pass of a divergent light beam. It can be installed directly on the outlet stack. The dust concentration is measured depending upon the amount of light blocked by suspended articles in exhaust gas. Advanced techniques are effectively used to detect & compensate for errors due to ambient light as well as stationary dust giving accurate emission readings. Unique design of Swirling Chamber ensures effective cleaning of lenses. Due to its unique algorithm of time-based accumulation of opacity, the EM919 can give emission per normalized gas volume (i.e. in mgNm3)

IFI has been a pioneer in applying Air Pollution Control Techniques in day to day process operations.
A striking example of this pioneering approach is IFIs Simple & Efficient Sack Feeding & Dosing system.
Compact, Sturdy & Ergonomically designed to suit various industrial applications. This unique equipment can be effectively used for dosing of various powders in the food, cosmetic, chemical and dairy industry.
At the heart of IFIs Dosing system is a custom designed Dust Filter with Cleaning Arrangement, a Fan optimally designed and a Screw Conveyor which feeds the desired quantity of material into the onward system.

Multi louver Dampers manufactured by IFI offer a perfect solution to regulate and control gases in various process industries.
They are a type of venetian blind made up of various parallel blades which can be opened and closed in parallel or in opposite directions.
The blades normally have an aerodynamic profile which minimizes head losses.
These are designed in circular or rectangular form according to the installed situation. A defined number of damper blades determined by the duct cross section and damper function are arranged in a robust flanged frame.
The actuation of the damper can be manual, motorized or pneumatic as the case may be. Actuators can be the onoff type or regulation type to which Proximity Sensor can be added, we can give signal to control room based on the level of automation required.

onisation Filtration Industries Pvt. Ltd. has taken a step forward and improved its manufacturing capabilities by setting up its own automated brand new line of Cage Manufacturing. IFI has always been a pioneer in offering new Technologies to our esteemed customers at affordable prices & at the same time maintaining world-class quality. With the newmanufacturing unit is based in Pirangut, located on the outskirts of Pune, Maharashtra, we are geared up to manufacture more than 1000 Cages per day.
Bag Filter Cages
Our cages are available in a variety of configurations, finishes and materials, including stainless steel.Heavy duty shipping crates are used to protect the cages during shipment and at the site.

The Bag Filter Controller also known as a Sequential timer is a Sophisticated Electrical unit which is primarily responsible for controlling the Purging Cycles of a Bag Filter.

The Integrated Bag Filter Controller
IFI's integrated programmable bag filter controller helps you get the best performance out of your Bag Filter.
It integrates all important signals associated with a bag filter & produces the most efficient cleaning program. The Inputs & Outputs of the IPBC can be configured as per user requirement.

There was a time when smoke bellowing out of a chimney was considered to be a sign of industrialization. In todays environmentally cautious ageeven the analysis of suspended particles in visibly clean gas is mandatory.
ESP has proved itself time & again to be the most economical equipment for handling high volume gas. Thus making it the first choice for various industries.
With Ever increasing number of industrial processes, the importance of the ESP has
increased considerably.
The latest advancements in Electronic Control Systems has proved itself in enhancing the reliability & performance of the ESPs.
IFI brings the latest in ESP Technology right to your door step to fulfill the ever increasing needs of the industry.

Cleans the sack from bottom, sides and top
Installed at the sack discharge end of Rotary Packer.
Recovers the spillage and dust on the sack
Keeps the packing area clean
Improves the working environment
Uses the draught of the packer
No extra air used
Single drive in the form of geared motor

The bed of the sack sweeper is made of powered rollers. The hollow rollers are fitted with brush that rotates in the opposite direction to make the brushing effective. The top brushes are also powered and fitted with bristles that can clean the sacks from top and sides. The level of the top brush can be adjusted to compensate the reduced length of the brush when it wears off.
Safety covers are fitted on both sides. These covers are loaded with gas springs for ease of opening and closing.
The drive is in the form of cascaded chains and sprockets powered by a geared motor. The drive can be located on either side of the sack sweeper. The rpm of the geared motor can be chosen to suit the packer throughput.
Top bonnet can be opened and closed with ease with the help of gas springs.
Emergency stop push buttons are provided in all the four corners of the sweeper module

IFI designs, manufactures & supplies customized platforms which are pre fabricated& to be erected at site.
Customized designs allows us to make platform exactly as per user requirements so as to fit in existing space, around existing equipments and at varying heights.
IFI has internal engineering facilities to design platforms which are load bearing platforms on case to case basis.

Pre-fabricated platforms, staircases, ladders, railings allow easy erection at site which can be completed in the least possible time.
Platforms can be made in various MOCs like Mild Steel which can be Painted or Galvanized. Stainless Steel platforms can also be manufactured on request.

Fabric Filter Leak Detection System.
Ionisation Filtration Industries Pvt. Ltd. has always believed in offering new Technologies to our esteemed customers at affordable prices & at the same time maintaining world-class quality.
Finding leakages in a fabric filter is a laborious process which takes time & is often not carried out satisfactorily.
Leak Glo Manufacturer
With the Fabric Filter Leak Detection System maintenance of Fabric Filters has taken a quantum leap. Its ease of use & reduction in downtime of Fabric Filters makes it the preferred choice of all Maintenance Engineers.
The powder when thrown into the Bag House will follow the Path of the Gas. Where there is a leakage the gas will tend to exit through it. The fluorescent powder when it passes along with the gas through the leakage will glow in UV light supplied along with the Powder identifying the leakage with ease.

The screw sampler is designed for sample extraction of dry and non-sticky powdered material from a duct or chute through which free flow of material is taking place.
The sampler is driven by a geared motor coupled to a transport screw, crossing the flow of material. As an option, the screw sampler can be equipped with variable speed geared motor.
The screw transports the extracted material to a discharge outlet chute where the material falls by gravity to the subsequent sample preparation equipment.
The screw sampler type size and design is based on chute dimension in mm as well as chute form. It can be mounted in chutes (rectangular or circular)
The control of the sampler is normally conducted from your central PLC system or local control is also possible. It can be equipped with a motion detector as an option.
Manual type Screw Samplers are also available upon request.

Slide Gates are used to control and isolate the discharge of bulk materials from hoppers, bins, silos or conveyors.
Slide Gates consist of a rigid frame mounted to the bottom of the storage device or conveyor.
A slide plate is located inside the frame that either opens or closes against the flow of material. The slide plate can be moved by manual, pneumatic, electric or hydraulic means.

The slide plate being a wear component is made from high wear resistant material & can be offered in various MoCs.
IFI manufacture slide gates to meet specific customer requirements & sizes.

The ionisation process is governed by corona generation in an esp.
The specially designed pipe & spike emitting electrodes can generate desired amount of corona for a particular application.
The nails welded to the pipe provide sharp points for higher corona emission.
The number of nails per meter of electrode decides the corona density.
With our experience in various applications we can engineer correct characteristics of corona densities.
The corona density requirement changes from first to last field and a suited design for individual filed is engineered.
A continuous fabrication line produces high quality electrodes as per the desired user specifications.

Rotary Air Lock valves are one of the most commonly used Dust Extraction Systems in the Process Industry.
A rotary valve or airlock is used to feed solids between areas of differing pressure while still maintaining the pressure differential and product flow.
The word rotary refers to the fact that during operation of a rotary airlock, the vanes turn or rotate. As they turn, the pockets, which are formed between the vanes, become
rotating pockets. The bulk material being handled enters the pockets at the top, through the Inlet port, travels around in a rotating motion, and exits at the bottom, or through the Outlet port. As the vanes and pockets continue to turn, material continues to be moved from top to bottom, or from Inlet port to Outlet port, in a rotating motion.c

Guillotines provide a mechanized means of inserting a duct blanking plate and offer superior isolation of flue gas applications containing heavy particulate loads and are ideal for tight shut off applications.
IFI guillotine damper, has the main function of isolation of equipment to permit inspection, maintenance, or repair in addition to process isolation. Occasionally, guillotine dampers are specified for bypass ducts, if operation requirements allow enough time for the slow-moving blade to travel across the opening.
The standard guillotine model is designed forassembly to be performed in such a way that the gate slides vertically. The guillotine damper is made up of a gate whichslides along metal guides, closing the conduitcompletely. The ends are joined to the conduits bymeans of flanges. The guillotine damper isnormally supplied as a single part. The body of the guillotine damper can beinsulated externally depending upon application requirement

Bag Filters up to 20, 000 m3hr with high efficiency filtration systems are commonly used in the Industry.
Single Hopper entry is the most common type of Dust Entry method.

Simultaneous hopper entry can be done into Two Hoppers by giving a Y Joint at the inlet.
Inlet velocities are controlled at 10 ms for better performance of the Bag Filter.