Co.me.ar.molinari S.p.a.

ITALY, Italy

We are offering Tow Truck Se 300.The equipment his excellency se300 is applicable on trucks having a gross vehicle weight of 12000 kg minimum and, thanks to a particular ease of use, is particularly suited to the recovery and transport of vehicles. The size of the loading, provided in high-strength aluminum alloy (sea 300) or galvanized steel (se 300), may vary depending on the type of container and the needs of the customer. The special structure of the installation, which exploits a particularly low sub-frame, allows to have greater stability during transport. The set his excellency se 300 is the evolution of the designing his excellency se 200, which still remains in production. The novelty of the new construction is the crane arm is no longer secured to the deck and then roll-off with it, but via a structure attached to the chassis of the vehicle. This change made it possible to make a crane boom and a much longer range than previous (3.5 t in the standard version). In addition, this new configuration allows to use the crane arm for the recovery in the low position. The hydraulic winch, if required in the version with movable hydraulic particularly facilitates the loading of cars crashed. A request can be mounted behind the cab of a crane sling complete fixed or adjustable for lifting and loading cars. The hydraulic telescopic fork rear supplied in version 1.5 t or 2.5 t, allows the towing of cars or trucks lifted axle failure.

We are offering breakdown truck.breakdown truck setal 200 the equipment s.e.t.al. 200 is applicable on trucks having a gross vehicle weight minimum of 6500 kg and, thanks to a particular ease of use, is particularly suitable for the transport of vehicles. The dimensions of the loading surface, provided in aluminum alloy (setal. 200) or galvanized steel (setac. 200), can vary depending on the type of container and the needs of the customer. The special structure of the installation, consisting of a platform that scarra completely until it rests on the ground, facilitates the loading of vehicles with sports suspension or very low. Ideal for loading motor having a particularly long rear overhang and therefore difficult to load with a standard development. A request can be mounted rib with a sliding curtain sides and tailgate to protect the vehicle loaded. Alternatively, you can always fit a rigid body both hatchback and possibly with side door. The hydraulic telescopic fork rear supplied in the version of 1t or 2t, allows the towing of cars or trucks lifted axle failure. The construction s.e.t.al. 200 complies with the ec machinery directive attesting the conformity of the product with the essential requirements of safety and technical standards that are reference quality index for purchasers of the equipment.

We are offering breakdown truck. Breakdown truck dpv 200the equipment d.p.v. 200 is applicable on trucks having a gross vehicle weight minimum of 10000 kg and, thanks to a particular ease of use, is particularly suitable for the transport of more vehicles.the size of the loading, provided in galvanized steel, can vary depending on the type of container and the needs of the customer. The upper comes in high strength aluminum alloy (dpv 200) or, on request, galvanized steel (s 200 dpv).the special structure of the installation, which exploits a particularly low sub-frame, allows to have greater stability during transport.a request is possible to realize, in perte rear of the vehicle, the lowering of the original frame to mount a ball hitch for towing a cart.a request can be mounted on the upper loading deck a second winch to facilitate the loading of motor vehicles.the hydraulic telescopic fork rear supplied in the version of 1t or 2t, allows the towing of cars or trucks lifted axle failure.on request, to increase the functionality of the equipment, it is possible to mount a hydraulic crane arm additional retractable firmly anchored in the rear of the loading floor.built in high-strength steel, the arm crane 3.5t is equipped with two hydraulic cylinders for lifting and one for the extension.e 'possible to realize a special version (dpa) completely of aluminum alloy applied on trucks having a gross vehicle weight of at least 7500 kg; that version has the lower surface fixed, inclined in the rear, and the load of the car is through two platforms manuals.the construction d.p.v. 200 complies with the ec machinery directive attesting the conformity of the product with the essential requirements of safety and technical standards that are reference quality index for purchasers of the equipment.

We are offering breakdown truck.breakdown truck city star the preparation city star is applicable on trucks having a gross vehicle weight minimum of 3500 kg and is characterized by its extreme ease and speed of action in any situation. The dimensions of the loading surface, provided in aluminum alloy or steel, may vary depending on the type of container and the needs of the customer. The particular position of the platform, which in the resting phase is presented with the height from the ground greatly reduced compared to current standards, allows to have a lower center of gravity and therefore a greater stability during transport. The subframe driving completely of aluminum alloy has allowed to reduce further the structure of canvas to have a higher flow rate. The hydraulic winch, as movable with hydraulic ease the load of cars particularly crashed. The construction product for both city star classic has an approach angle of 13 to the ground allowing the ascent of all vehicles in circulation. The version new produced with an angle of attack to the ground of 10 also allows the load of vehicles with sporting arrangements. Available for the following vehicles: fiat 250 ducato ford transit isuzu npr iveco daily mercedes-benz sprinter mitsubishi canter nissan cabstar-atleon renault maxity-mascots volkswagen crafter

We are offering breakdown truck. Breakdown truck pf 1500 the equipment pf 1500 is applicable on trucks with a total weight of 3.5 t with front-wheel drive and is composed of a low frame of aluminum alloy and an aluminum alloy inclined floor in the rear. The height from the ground very small allows to have greater stability during driving on the road. The double rear axle is tested at 2.7 t to reach a top speed of 145 km / h and is adjustable under load from an electro. The platform edge folding allows to minimize the inclination during the loading. The hydraulic winch, in the version with manual movable ease the load of cars particularly crashed. Thanks to the loading platform constructed to measure, the equipment pf 1500 has a maximum angle of attack to the ground of 8 .

We are offering breakdown truck.the breakdown truck se 200 the equipment his excellency mr 200 l is applicable on trucks having a gross vehicle weight minimum of 5000 kg and, thanks to a particular ease of use, is particularly suited to the recovery and transport of vehicles. The size of the loading, provided in high-strength aluminum alloy (sea 200 l) or galvanized steel (200 l se) may vary depending on the type of container and the needs of the customer. The special structure of the installation, which exploits a particularly low sub-frame, allows to have greater stability during transport. The hydraulic winch, if required in the version with movable hydraulic particularly facilitates the loading of cars crashed. The hydraulic telescopic fork rear supplied in the version of 0.8 t or 1t, allows the towing of vehicles with axle raised in failure. On request, to increase the functionality of the equipment, it is possible to mount a hydraulic crane arm additional retractable firmly anchored in the rear of the loading floor. Built in high-strength steel, the crane arm from 2t is equipped with two hydraulic cylinders for lifting and one for the extension.

We are offering breakdown truck. Breakdown truck rftgthe equipment r.f.t.g. Is applicable on trucks having a gross vehicle weight minimum of 3500 kg and, thanks to a particular ease of use, is particularly suitable for the forced removal of parked cars. the hydraulic winch, positioned on the arm allows the use of the arm itself as a crane for the recovery of crashed cars. the sling used to lift the car parked, placing them on the road and tow-axis raised. the rudder spacer placed between the sling and prevents the rescue wagon uto the car while driving. a request can be fitted with a hydraulic rear fork. you can monatre a gallows rear hydraulic swivel to facilitate the removal of parked cars. the construction r.f.t.g. Complies with the ec machinery directive attesting the conformity of the product with the essential requirements of safety and technical standards that are reference quality index for purchasers of the equipment.

We are offering breakdown truck. St 400 breakdown truck the equipment s.t. 400 is applicable on trucks having a gross vehicle weight minimum of 18000 kg and, thanks to a particular ease of use, is particularly suited to the recovery and transport of goods vehicles. The dimensions of galvanized steel load may vary depending on the type of container and the needs of the customer. The special structure of the display, which utilizes a robust sub-frame, allows to have a greater resistance during loading and transport. The hydraulic winch, if required in the version with movable hydraulic particularly facilitates the loading of trucks involved in accidents. A request can be mounted behind the cab of a crane sling complete fixed or adjustable for lifting and loading cars. The hydraulic telescopic fork rear supplied in the version of 3t, 4t or 6t, allows the tow truck with axle raised in failure. On request, to increase the functionality of the equipment, it is possible to mount a hydraulic crane arm additional retractable firmly anchored in the rear of the loading floor. Built in high-strength steel, the arm crane 3.5t is equipped with two hydraulic cylinders for lifting and one for the extension.

We are offering breakdown truck.breakdown truck fp 8000 the equipment fp 8000 is applicable on trucks with three or more axes with a total weight to the ground minimum of 26000 kg. Thanks to a special ease of use, is particularly suited to the recovery and transport of heavy goods vehicles with axle raised in failure. Firmly anchored to the frame, is fixed arm cranes lifted by two hydraulic cylinders on which are fixed one or two hydraulic winches with a capacity of 30 t and 15 t, which permit the recovery of heavy vehicles. Through the referral of the rope with a flag placed on the scaffold results in a hoist with a capacity of 8 t with fork and fully parade of 10 t with fork fully retracted. To promote the stability of the medium during recovery with the cranes, the display is equipped with two hydraulic stabilizer legs firmly anchored to the subframe. On request is possible to mount a crane behind the cab. such a crane (mounted only on vehicles with 4-axis) is used for the recovery of the damaged vehicles. A request can be mounted inside a telescoping boom crane with a capacity of 10t. This extension is used for the recovery of the damaged vehicles or for lifting the vehicle to be loaded on the scaffold. The hydraulic telescopic fork completely parade allows towing with a truck axle raised in failure with a maximum axle weight of 8000 kg. The three extensions of the arm of the fork make it easy to tow buses or trucks with the long front overhang. The particular movement of the arm of the fork makes it easy recovery of vehicles having a height from the ground is very limited. The set fp 8000 meets the ec machinery directive attesting the conformity of the product with the essential requirements of safety and technical standards that are reference quality index for purchasers of the equipment.

We are offering breakdown truck. Breakdown truck psl the equipment p.s.l. Is applicable on trucks having a gross vehicle weight minimum of 7500 kg and, thanks to a particular ease of use, is particularly suited to the recovery of the damaged vehicles. The dimensions of the loading platform, equipped with 2 mats made of aluminum alloy, can vary depending on the type of container and the needs of the customer. The special construction of the installation, which exploits a particularly low sub-frame, allows to have greater stability during transport. The hydraulic winch, if required in the version with movable hydraulic particularly facilitates the loading of cars crashed. A request can be mounted behind the cab of a crane sling complete fixed or adjustable for lifting and loading cars. The hydraulic telescopic fork rear supplied in the version of 1t or 2t, allows the towing of cars or trucks lifted axle failure. Firmly anchored to the frame, is fixed crane with an arm raised by 2 hydraulic cylinders and telescoping hydraulic cylinder via a. Constructed of high strength steel, the hoist is provided in version 5.5t and 4t.

We are offering breakdown truck.pfa breakdown truckthe construction p.f.a. Is applicable on trucks having a gross vehicle weight minimum of 3500 kg and is characterized by its extreme ease and speed of action in any situation. the dimensions of the loading surface, provided in aluminum alloy, can vary depending on the type of container and the needs of the customer. the load of the car is done by hand two platforms of aluminum alloy. the particular very light structure allows higher flow rates compared to current standards, also the particular position of the platform with the height from the ground greatly reduced, allows to have a lower center of gravity and therefore a greater stability during transport. the construction p.f.a. Complies with the ec machinery directive attesting the conformity of the product with the essential requirements of safety and technical standards that are reference quality index for purchasers of the equipment.