My ExportersIndia

For Buyer

For Seller

For Help

Jabbals - Testing Equipment

Our Complete range of products are Hipot Tester, Rotor Tester, Hi-Pot tester and Surge Tester.

Hipot Tester

    Jabbals Hipot Tester

    • Max Output Voltage10000 Volts
    • Max Leakage Current2000 μAmps

    the latest dc hi-pot tester provides a cost-effective solution to perform hi-pot testing of cables, generators, motors & other electrical products. User friendly front panel controls, high fault detection capability, insulated test probe to allow easy application of the high voltage to the device under the test.

    View Complete Details
    Rotor Tester

      Rotor Tester

      Principle of Rotor Testing

      The Rotor tester uses the principle of electrical and magnetic effects caused by the circulation of induced currents into the bars of a rotor, which is made to turn at a constant speed, with in a magnetic field produced by a permanent magnet. The induced magnetic field produced by permanent magnet, acts on one slot at a time. The direction of magnetic field is such that the turns of a moving rotor cut the lines of force normally. The induced currents, which are proportional to the field intensity (distance of magnet from the rotor, on the speed of rotation constant) & on the rotor characteristics, produce magnetic fields, the symmetry of which enable a clear observation of the turns in the short-circuited condition. A fixed probe subjected to the magnetic fields produced by the rotor under test, provides the signals, which after being amplified, are applied to the monitor. The synchronized sinusoidal wave pattern from the rotor bars is displayed on the monitor screen. The waveform identifies typically occurring faults in the rotor bars & there is a distant correlation between the result of the inductive test of the rotor bars & the starting torque of a motor.
      View Complete Details
      Hi-Pot tester

        Hi-Pot Tester

        The latest DC Hi-Pot tester provides a cost-effective solution to perform Hi-Pot testing of cables, generators, motors & other electrical products.

        BENEFITS

        • User friendly front panel controls
        • High fault detection capability
        • Non-destructive to insulation
        • Zero start lock for operator safety
        • Insulated Test Probe to allow easy application of the high voltage to the device under the test
        • Shielded output test leads
        • Test leads energized warning indicator
        • Auto/Manual test mode
        • Adjustable test time in the Auto mode
        • Continuously adjustable output test voltage
        • Accurate 3 Digits LED Display for DC Hi-Pot test voltage and Leakage current
        • Go/No-Go Leakage current trip indicator and buzzer


        APPLICATIONS

        • Transformers
        • Switchgear & Relays
        • Motors
        • Coils & Chokes
        • Generators
        • Capacitors
        • Wires & Cables
        • Other electrical apparatus

        Model3010HP3025HP3050HP
        Max Output Voltage10000 Volts25000 Volts50000 Volts
        Max Leakage Current2000 μAmps2000 μAmps2000 μAmps
        Max Trip Current2000 μAmps2000 μAmps2000 μAmps
        Max Test Time180 secs180 secs180 secs
        Display3½ Digits LED3½ Digits LED3½ Digits LED
        Power Consumption120 Watts300 Watts440 Watts
        Weight23kgs (50lbs)30kgs (70lbs)36kgs (80lbs)
        Operating Voltage230V ± 10%230V ± 10%230V ± 10%
        Operating Frequency50Hz ± 3%50Hz ± 3%50Hz ± 3%
        Physical Dimensions(W X H X D) mm380 X 210 X 485435 X 250 X 540475 X 320 X 570
        View Complete Details
        Surge Tester

          Jabbals Surge Tester

          the surge comparison tester checks the strength of ground insulation that consists of enameled insulation. It detects the insulation failures such as turn-to-turn shorts, layer-to-layer shorts, coil-to-coil shorts, winding-to-winding shorts, and phase-to-phase shorts. Open circuit and ground detection are other benefits of surge testing. The surge tester uses the principle of impedance balance to test the quality of electrical windings.the surge tester works as a capacitive-discharge system. A capacitor is charged with high voltage and then discharged into the winding, through a solid state assembly. This sequence is repeated thus stressing the insulation of the winding with high voltage pulses.

          View Complete Details
          Tell Us What are you looking for? Will call you back

          Contact Us

          • icon userJabbals(Jabbals)
          • location iconPlot No. 20A/14-15, Industrial Area Faridabad – 121 001, Haryana India - 121001
          • share iconShare us via
          • Manufacturers In Faridabad