Write a Review
Our Products
We offer a complete product range of Aluminium 5086 Sheet, Aluminium 5052 Plate, Aluminium 1070 Hex Bars, Aluminium 1060 Pipes and Aluminium 1070 Pipes
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1060 | O | 55 | 75 | 25 | 25 | 30 |
| H12 | 75 | 110 | 6 | 6 | 7 | |
| H14 | 90 | 120 | 5 | 5 | 6 | |
| H16 | 95 | 130 | 4 | 4 | 4 | |
| H18 | 130 | --- | 3 | 3 | 3 | |
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
| Poisson's Ratio | 0.27-0.30 | 25 | |
| Elastic Modulus (GPa) | 190-210 | 25 | |
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
| Yield Strength (Mpa) | 495 | ||
| Elongation (%) | 10 | ||
| Reduction in Area (%) | 45 | ||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
Aluminium 2014 Sheets Chemical Composition
| Alloy | Si | Fe | Cu | Zn | Mn | Mg | Ti | Other | Cr | Ni | Others | Ti+Zr | Al |
| 2014 (min) (max) | 0.50 - 0.90 | 0.0 - 0.50 | 3.90 - 5.00 | 0.0 - 0.25 | 0.40 - 1.20 | 0.20 - 0.80 | 0.0 - 0.15 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.20 | Balance |
Mechanical Properties of Aluminum 2014 Sheets
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
| - | - | Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) |
| EN AW-2014 | O | – | 250 | – | 135 | 10 |
| T4 | 370 | – | 230 | – | 11 | |
Aluminium 2024 Sheets Chemical Composition
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
| min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
| max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
Mechanical Properties of Aluminum 2024 Sheets
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| (annealed) | 32 | 14 | 12 |
| T3 | 63 | 42 | 15 |
Aluminium 3003 Sheets Chemical Composition
| Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
| Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
Mechanical Properties of Aluminum 3003 Sheets
| Properties | Metric | Imperial |
| Tensile strength | 130 MPa | 18855 psi |
| Yield strength | 125 MPa | 18130 psi |
| Shear strength | 83 MPa | 12039 psi |
| Fatigue strength | 55 MPa | 7977 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Elongation | 10% | 10% |
| Hardness | 35 | 35 |
Aluminium 5005 Sheets Chemical Composition
|
Element |
% |
Element |
% |
|
Aluminium |
Balance |
Manganese |
0.20 max |
|
Magnesium |
0.50 – 1.10 |
Chromium |
0.10 max |
|
Silicon |
0.30max |
Zinc |
0.25 max |
|
Iron |
0.07 max |
Others, each |
0.05 max |
|
Copper |
0.20 max |
Others, total |
0.15 max |
Mechanical Properties of Aluminum 5005 Sheets
|
Temper |
0.2% Proof Stress, MPa min† |
Tensile Strength, MPa |
Elongation % min‡ |
|
O (annealed) |
35 |
105 – 145 |
12 – 22 |
|
H12 |
95 |
125 – 165 |
2 – 8 |
|
H14 |
115 |
145 – 185 |
1 – 6 |
|
H16 |
135 |
165 – 205 |
1 – 3 |
|
H18 |
– |
> 185 |
1 – 3 |
|
H32 |
85 |
115 – 160 |
3 – 9 |
|
H34 |
105 |
135 – 180 |
2 – 7 |
|
H36 |
125 |
160 – 200 |
1 – 4 |
|
H38 |
– |
> 180 |
1 – 4 |
Aluminium 5754 Sheets Chemical Composition
| Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
| 2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 |
Balance
|
Mechanical Properties of Aluminum 5754 Sheets
| Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
| 80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
Aluminium 5082 Sheets Chemical Composition
| Al | Cr | Cu | Fe | Mg | Mn | Si | Ti | Zn | Residuals |
| 95.2 to 98.3% | 0.25% max | 0.1% max | 0.5% max | 0.6 to 1.2% | 0.4% to 1.0% | 0.7 to 1.3% | 0.1% max | 0.2% max | 0.15% max |
Mechanical Properties of Aluminum 5082 Sheets
| Melting Point | Modulus of Elasticity | Electrical Resistivity | Thermal Conductivity | Thermal Expansion | Specific Heat |
| 2700 kg/m3 | 555°C | 70 GPa | 0.038x10-6 Ω.m | 180 W/m.K | 24x10-6 /K |
Aluminium 5083 Sheets Chemical Composition
| Al | Si | Fe | Cu | Mn | Cr | Mg | Ti | Zn | Other Each | Others Total |
| Bal | 0.40 max | 0.40 max | 0.10 max | 0.40 / 1.0 | 0.05 / 0.25 | 4.0 / 4.90 | 0.15 max | 0.25 max | 0.05 max | 0.15 max |
Mechanical Properties of Aluminum 5083 Sheets
| Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
| 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
Aluminium 5086 Sheets Chemical Composition
| Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Others, each | Others, total | Al |
| 0.4 | 0.5 | 0.1 | 0.20-0.70 | 3.5-4.5 | 0.05-0.25 | 0.25 | 0.15 | 0.05 | 0.15 | Balance |
Mechanical Properties of Aluminum 5086 Sheets
| Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
| 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
| Mn | Si | Cr | Cu | Fe | Zn | Al | Mg | Ti | Other Each/Total |
| 0.15 | 0.4-0.8 | 0.15-0.35 | 0.15-0.4 | 0.7 | 0.25 | Remainder | 0.8-1.2 | 0.15 | 0.005/0.15 |
| Tensile Strengtd (PSI) | Yield Strengtd (PSI) | Shear Strengtd (PSI) | Elongation in 2″ | Brinell Hardness |
| 45,000 | 40,000 | 31,000 | 12 | 95 |
| Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Other Each | Others Total | Al |
| .10 (max) | .20/.60 | .35 (max) | .10 (max) | .45/.90 | .10 (max) | .10 (max) | .10 (max) | .05 | .015 | Remainder |
| Tensile Strength (psi) | Yield Strength (psi) | Elongation (% in 2") | Brinell Hardness |
| 27,000 | 21,000 | 12 | 60 |
| Weight % | Zn | Cu | Mg | Zr | Fe | Si | Mn | Ti | Cr | Others(total) |
| Minimum | 5.7 | 2.0 | 1.9 | 0.08 | - | - | - | - | - | - |
| Maximum | 6.7 | 2.6 | 2.6 | 0.15 | 0.15 | 0.12 | 0.10 | 0.06 | 0.04 | 0.15 |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 7050 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 7050 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
Mechanical Properties of Aluminum 1050 Plates
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
| Poisson's Ratio | 0.27-0.30 | 25 | |
| Elastic Modulus (GPa) | 190-210 | 25 | |
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
| Yield Strength (Mpa) | 495 | ||
| Elongation (%) | 10 | ||
| Reduction in Area (%) | 45 | ||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
| min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
| max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| (annealed) | 32 | 14 | 12 |
| T3 | 63 | 42 | 15 |
|
Element |
% |
Element |
% |
|
Aluminium |
Balance |
Manganese |
0.20 max |
|
Magnesium |
0.50 – 1.10 |
Chromium |
0.10 max |
|
Silicon |
0.30max |
Zinc |
0.25 max |
|
Iron |
0.07 max |
Others, each |
0.05 max |
|
Copper |
0.20 max |
Others, total |
0.15 max |
|
Temper |
0.2% Proof Stress, MPa min† |
Tensile Strength, MPa |
Elongation % min‡ |
|
O (annealed) |
35 |
105 – 145 |
12 – 22 |
|
H12 |
95 |
125 – 165 |
2 – 8 |
|
H14 |
115 |
145 – 185 |
1 – 6 |
|
H16 |
135 |
165 – 205 |
1 – 3 |
|
H18 |
– |
> 185 |
1 – 3 |
|
H32 |
85 |
115 – 160 |
3 – 9 |
|
H34 |
105 |
135 – 180 |
2 – 7 |
|
H36 |
125 |
160 – 200 |
1 – 4 |
|
H38 |
– |
> 180 |
1 – 4 |
| Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Al |
| 0.50 | 0.50 | 3.8/4.9 | 0.30/0.9 | 1.2/1.8 | 0.10 | 0.25 | 0.15 | Balance |
| Hardness, Brinell | Poisson's Ratio | Melting Point | Electrical Resistivity | Modulus of Elasticity | Specific Heat |
| 47 | 0.33 | 607 - 649 °C | 4.99e-006 ohm-cm | 70.3 GPa | 0.88 J/g-°C |
| Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
| 2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 | Balance |
| Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
| 80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
| Al | Cu | Mn | Cr | Si | Fe | Ti | Mg | Zn | Other Each | Others Total |
| Bal | 0.10 max | 0.40 / 1.0 | 0.05 / 0.25 | 0.40 max | 0.40 max | 0.15 max | 4.0 / 4.90 | 0.25 max | 0.05 max | 0.15 max |
| Weight % | Zn | Cu | Mg | Zr | Fe | Si | Mn | Ti | Cr | Others(total) |
| Minimum | 5.7 | 2.0 | 1.9 | 0.08 | - | - | - | - | - | - |
| Maximum | 6.7 | 2.6 | 2.6 | 0.15 | 0.15 | 0.12 | 0.10 | 0.06 | 0.04 | 0.15 |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 7050 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 7050 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
| Weight % | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Each | Total |
| Minimum | 1.20 | 2.10 | 0.18 | 5.10 | ||||||
| Maximum | 0.40 | 0.50 | 2.00 | 0.30 | 2.90 | 0.28 | 6.10 | 0.20 | 0.05 | 0.15 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
| Aluminum, Al | Silicon, Si + Iron, Fe |
Zinc, Zn |
Copper, Cu. | Titanium, Ti | Manganese, Mn | Other (each) | Other (total) |
|---|---|---|---|---|---|---|---|
| ≥ 99 | ≤ 1 | ≤ 0.10 | ≤ 0.050 | ≤ 0.050 | ≤ 0.050 | ≤ 0.050 | ≤ 0.15 |
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength | 70 - 105 MPa | 10152-15228 psi |
| Weight % | Zn | Cu | Mg | Zr | Fe | Si | Mn | Ti | Cr | Others (total) |
| Minimum | 5.7 | 2.0 | 1.9 | 0.08 | - | - | - | - | - | - |
| Maximum | 6.7 | 2.6 | 2.6 | 0.15 | 0.15 | 0.12 | 0.10 | 0.06 | 0.04 | 0.15 |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 8011 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 8011 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 8011 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
| Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Al |
| 0.50 | 0.50 | 3.8/4.9 | 0.30/0.9 | 1.2/1.8 | 0.10 | 0.25 | 0.15 |
Balance
|
| Hardness, Brinell | Poisson's Ratio | Melting Point | Electrical Resistivity | Modulus of Elasticity | Specific Heat |
| 47 | 0.33 | 607 - 649 °C | 4.99e-006 ohm-cm | 70.3 GPa | 0.88 J/g-°C |
| Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
| 2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 |
Balance
|
| Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
| 80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
| Al | Cr | Cu | Fe | Mg | Mn | Si | Ti | Zn | Residuals |
| 95.2 to 98.3% | 0.25% max | 0.1% max | 0.5% max | 0.6 to 1.2% | 0.4% to 1.0% | 0.7 to 1.3% | 0.1% max | 0.2% max | 0.15% max |
| Melting Point | Modulus of Elasticity | Electrical Resistivity | Thermal Conductivity | Thermal Expansion | Specific Heat |
| 2700 kg/m3 | 555°C | 70 GPa | 0.038x10-6 Ω.m | 180 W/m.K | 24x10-6 /K |
| Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Others, each | Others, total | Al |
| 0.4 | 0.5 | 0.1 | 0.20-0.70 | 3.5-4.5 | 0.05-0.25 | 0.25 | 0.15 | 0.05 | 0.15 | Balance |
| Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
| 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
| ALUMINIUM Alloy | % Si |
% Mg |
% Mn |
% Cu |
% Fe |
% Cr |
% Zn |
% Ti |
% Others |
% Al |
|---|---|---|---|---|---|---|---|---|---|---|
| EN AW-1100 | Si+Fe 0.95 Max | – | 0.05 Max | 0.05 – 0.20 | – | – | 0.10 Max | 0.05 Max | – | 99.0 Min |
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1100 | O | 75 | 110 | – | – | 25 |
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 8011 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 8011 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 8011 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Mechanical Properties - Al 1060 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
| H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
| H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
| H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
| H18 | 130 | --- | 3 | 3 | 3 | ||||||||||||||
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
| Poisson's Ratio | 0.27-0.30 | 25 | |
| Elastic Modulus (GPa) | 190-210 | 25 | |
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
| Yield Strength (Mpa) | 495 | ||
| Elongation (%) | 10 | ||
| Reduction in Area (%) | 45 | ||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
| Alloy | Si | Fe | Cu | Zn | Mn | Mg | Ti | Other | Cr | Ni | Others | Ti+Zr | Al |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 2014 (min) (max) | 0.50 - 0.90 | 0.0 - 0.50 | 3.90 - 5.00 | 0.0 - 0.25 | 0.40 - 1.20 | 0.20 - 0.80 | 0.0 - 0.15 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.20 | Balance |
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| - | - | Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) |
| EN AW-2014 | O | – | 250 | – | 135 | 10 |
| T4 | 370 | – | 230 | – | 11 | |
| Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
| Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
| Properties | Metric | Imperial |
| Tensile strength | 130 MPa | 18855 psi |
| Yield strength | 125 MPa | 18130 psi |
| Shear strength | 83 MPa | 12039 psi |
| Fatigue strength | 55 MPa | 7977 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Elongation | 10% | 10% |
| Hardness | 35 | 35 |
| Material | Temper | Tensile Strength (N/mm²) | Yield Strength (N/mm²) | Elongation on 50mm (%) | |||
| 0.5 mm | 0.8 mm | 1.3 mm | 2.6mm | ||||
| 5005 | 0 | 95-145 | - | 18 | 20 | 21 | 22 |
| 5005 | H12 | 125-170 | 80 | 4 | 5 | 6 | 8 |
| 5005 | H14 | 145-185 | 100 | 3 | 3 | 5 | 6 |
| 5005 | H18 | 185 min | 165 | 1 | 2 | 3 | 3 |
| Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Other Each | Others Total | Al |
| .10 (max) | .20/.60 | .35 (max) | .10 (max) | .45/.90 | .10 (max) | .10 (max) | .10 (max) | .05 | .015 | Remainder |
| Weight % | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Each | Total |
| Minimum | 1.20 | 2.10 | 0.18 | 5.10 | ||||||
| Maximum | 0.40 | 0.50 | 2.00 | 0.30 | 2.90 | 0.28 | 6.10 | 0.20 | 0.05 | 0.15 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1060 | O | 55 | 75 | 25 | 25 | 30 |
| H12 | 75 | 110 | 6 | 6 | 7 | |
| H14 | 90 | 120 | 5 | 5 | 6 | |
| H16 | 95 | 130 | 4 | 4 | 4 | |
| H18 | 130 | --- | 3 | 3 | 3 | |
| Al | Si | Fe | Cu | Mn | Cr | Mg | Ti | Zn | Other Each | Others Total |
| Bal | 0.40 max | 0.40 max | 0.10 max | 0.40 / 1.0 | 0.05 / 0.25 | 4.0 / 4.90 | 0.15 max | 0.25 max | 0.05 max | 0.15 max |
| Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
| 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 7050 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 7050 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
| Weight % | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Each | Total |
| Minimum | 1.20 | 2.10 | 0.18 | 5.10 | ||||||
| Maximum | 0.40 | 0.50 | 2.00 | 0.30 | 2.90 | 0.28 | 6.10 | 0.20 | 0.05 | 0.15 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1060 | O | 55 | 75 | 25 | 25 | 30 |
| H12 | 75 | 110 | 6 | 6 | 7 | |
| H14 | 90 | 120 | 5 | 5 | 6 | |
| H16 | 95 | 130 | 4 | 4 | 4 | |
| H18 | 130 | --- | 3 | 3 | 3 | |
| Alloy | Si | Fe | Cu | Zn | Mn | Mg | Ti | Other | Cr | Ni | Others | Ti+Zr | Al |
| 2014 (min) (max) | 0.50 - 0.90 | 0.0 - 0.50 | 3.90 - 5.00 | 0.0 - 0.25 | 0.40 - 1.20 | 0.20 - 0.80 | 0.0 - 0.15 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.20 | Balance |
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
| - | - | Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) |
| EN AW-2014 | O | – | 250 | – | 135 | 10 |
| T4 | 370 | – | 230 | – | 11 | |
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
| min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
| max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| (annealed) | 32 | 14 | 12 |
| T3 | 63 | 42 | 15 |
| Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
| Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
| Properties | Metric | Imperial |
| Tensile strength | 130 MPa | 18855 psi |
| Yield strength | 125 MPa | 18130 psi |
| Shear strength | 83 MPa | 12039 psi |
| Fatigue strength | 55 MPa | 7977 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Elongation | 10% | 10% |
| Hardness | 35 | 35 |
| Weight % | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Each | Total |
| Minimum | 1.20 | 2.10 | 0.18 | 5.10 | ||||||
| Maximum | 0.40 | 0.50 | 2.00 | 0.30 | 2.90 | 0.28 | 6.10 | 0.20 | 0.05 | 0.15 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
| Alloy | Temper | UTS (Mpa) | Elongation (%) | |||
|---|---|---|---|---|---|---|
| 1060 | Minimum | Maximum | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |
| 0 | 55 | 75 | 25 | 25 | 30 | |
| H14 | 90 | 120 | 5 | 5 | 6 | |
| Alloy | Equivalent alloy (A.A) | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI | |||||||||||
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1C | 19000 | 1100 | 0.35 | 0.50 | 0.25 | 0.35 | 0.01 | 0.03 | 0.01 | 0.05 | 0.05 | 0.20 | 0.01 | 0.05 | 0.020 | 0.030 | Trace | Trace | 0.05 (each) | 0.15 (total) | 99.60% | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | H14 | 75 | 110 | 20 | 25 | 29 |
| 95 | 130 | 5 | 6 | 7 | ||
| 110 | 145 | 3 | 4 | 5 | ||
| 130 | 165 | 2 | 3 | 4 | ||
| 150 | --- | 2 | 2 | 3 | ||
| Alloy | Equivalent alloy (A.A) | Si | Fe | Cu | Zn | Mn | Mg | Ti | Cr | Others | AI | |||||||||||
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| H15 | 24345 | 2014 | 0.50 | 0.90 | 0.0 | 0.50 | 3.90 | 5.00 | 0.00 | 0.25 | 0.40 | 1.20 | 0.20 | 0.80 | 0.0 | 0.15 | 0.0 | 0.10 | 0.0 (each) | 0.05 (total) | balance | |
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| - | - | Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) |
| EN AW-2014 | O | – | 250 | – | 135 | 10 |
| T4 | 370 | – | 230 | – | 11 | |
| Alloy | Equivalent alloy (A.A) | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other each | Other total | AI | ||||||||||||
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| H14 | 24534 | 2017 | 0.20 | 0.8 | - | 0.7 | 3.5 | 4.5 | 0.40 | 1.0 | 0.40 | 0.8 | - | 0.10 | - | 0.25 | - | 0.15 | - | 0.05 | - | 0.15 | bal | |
| Alloy | Temper | Tensile Strength (N/mm²) min | Yield Strength (Mpa) | Elongation in 4D % | ||
|---|---|---|---|---|---|---|
| T6 | ksi | Mpa | ksi | Mpa | A 50mm (Minimum) | |
| 2017 | T651 | 60 | – | 20 | – | 23 |
| T6511 | 60 | 95 | 20 | – | 23 | |
| Temper | Tensile Strength | Yield Strength | Elongation |
| T6 | KSI | KSI | % |
| T65 | 32 | 14 | 12 |
| T651 | 63 | 42 | 15 |
| Alloy | Specified thickness | Tensile strength |
Yield strength |
Elongation | ||||||||
| (MPa) | (MPa) | (%) | ||||||||||
| 5005 | 0.2~0.63mm | 138.179 | Min104 | min 3 | ||||||||
| 0.63~1.2mm | min 4 | |||||||||||
| 1.2~6.3mm | min 5 | |||||||||||
| 6.3~50mm | min 8 | |||||||||||
| 0.2~600mm | 118-158 | Min83 | min 3 | |||||||||
| 145-186 | min118 | min1 | ||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 5052 | H32 | 171 | 213 | 16 | 18 | 19 |
| 213 | 261 | 5 | 7 | 9 | ||
| 233 | 281 | 4 | 6 | 7 | ||
| 254 | 302 | 3 | 4 | 4 | ||
| 268 | - | 3 | 4 | 4 | ||
| Alloy | Temper | Thermal conductivity | Coefficient of thermal expansion | Melting point | Elastic modulus | Electrical conductivity | |
|---|---|---|---|---|---|---|---|
| W/m*K | µm/(m*K) | Min | Max | KN/mm2 | %IACS | ||
| 5754 | H22 | 132 | 23,7 | 595 | 645 | 70 | 32,5 |
| 132 | 23,7 | 595 | 645 | 70 | 32,5 | ||
| 132 | 23,7 | 595 | 645 | 70 | 32,5 | ||
| 132 | 23,7 | 595 | 645 | 70 | 32,5 | ||
| 23,7 | 595 | 645 | 70 | ||||
| 132 | 23,7 | 595 | 645 | 70 | 32,5 | ||
| Material | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 Angle (AMS 4340) | 79 | 69 | 7 |
| Aluminium Alloy 7050 Angle (AMS 4340) | 70 | 60 | 8 |
| Aluminium Alloy 7050 Angle (AMS 4342) | 73 | 63 | 7 |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Mechanical Properties - Al 1060 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
| H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
| H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
| H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
| H18 | 130 | --- | 3 | 3 | 3 | ||||||||||||||
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
| Poisson's Ratio | 0.27-0.30 | 25 | |
| Elastic Modulus (GPa) | 190-210 | 25 | |
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
| Yield Strength (Mpa) | 495 | ||
| Elongation (%) | 10 | ||
| Reduction in Area (%) | 45 | ||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Thermal Expansion (10-6/ºC) | 11.8 | 0-100 more | rolled |
| Mechanical Properties - AA 1100 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1100 | O | 75 | 110 | 20 | 25 | 29 | |||||||||||||
| H12 | 95 | 130 | 5 | 6 | 7 | ||||||||||||||
| H14 | 110 | 145 | 3 | 4 | 5 | ||||||||||||||
| H16 | 130 | 165 | 2 | 3 | 4 | ||||||||||||||
| H18 | 150 | --- | 2 | 2 | 3 | ||||||||||||||
| Material | Temper | Diameter (mm) | Tensile Strength min ((N/mm²) | Yield Strength (min) (N/mm²) | Elongation on 5.65 V (min) |
| 2014 Bar | T4 | <20 | 370 | 230 | 11 |
| 2014 Bar | T4 | 20-75 | 390 | 250 | 11 |
| 2014 Bar | T4 | 75-150 | 390 | 250 | 9 |
| 2014 Bar | T4 | 150-200 | 370 | 230 | 8 |
| 2014 Bar | T6510 | 20-75 | 480 | 435 | 7 |
| 2014 Bar | T6510 | 75-150 | 465 | 420 | 7 |
| 2014 Bar | T6510 | 150-200 | 435 | 390 | 7 |
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
| min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
| max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| (annealed) | 32 | 14 | 12 |
| T3 | 63 | 42 | 15 |
| Properties | Metric | Imperial |
| Tensile strength | 130 MPa | 18855 psi |
| Yield strength | 125 MPa | 18130 psi |
| Shear strength | 83 MPa | 12039 psi |
| Fatigue strength | 55 MPa | 7977 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Elongation | 10% | 10% |
| Hardness | 35 | 35 |
| Material | Temper | Tensile Strength (N/mm²) | Yield Strength (N/mm²) | Elongation on 50mm (%) | |||
| 0.5 mm | 0.8 mm | 1.3 mm | 2.6mm | ||||
| 5005 | 0 | 95-145 | - | 18 | 20 | 21 | 22 |
| 5005 | H12 | 125-170 | 80 | 4 | 5 | 6 | 8 |
| 5005 | H14 | 145-185 | 100 | 3 | 3 | 5 | 6 |
| 5005 | H18 | 185 min | 165 | 1 | 2 | 3 | 3 |
| Diameter or minor sectional dimension mm | Tensile Strength, MPa | Yield Strength 0.2%, MPa | Elongation % |
| 0-20 | 295 | 255 | 8 |
| 20-150 | 310 | 270 | 8 |
| 150-200 | 280 | 240 | 5 |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Material | Temper | Diameter (mm) | Tensile Strength min ((N/mm²) | Yield Strength (min) (N/mm²) | Elongation on 5.65 V (min) |
| 2014 Bar | T4 | <20 | 370 | 230 | 11 |
| 2014 Bar | T4 | 20-75 | 390 | 250 | 11 |
| 2014 Bar | T4 | 75-150 | 390 | 250 | 9 |
| 2014 Bar | T4 | 150-200 | 370 | 230 | 8 |
| 2014 Bar | T6510 | 20-75 | 480 | 435 | 7 |
| 2014 Bar | T6510 | 75-150 | 465 | 420 | 7 |
| 2014 Bar | T6510 | 150-200 | 435 | 390 | 7 |
Mechanical Properties of Aluminum 5754 Square Bars
| Thermal conductivity | Coefficient of thermal expansion | Melting point | Elastic modulus | Electrical conductivity | |||
|---|---|---|---|---|---|---|---|
| Alloy | Temper | W/m*K | µm/(m*K) | Min | Max | KN/mm2 | %IACS |
| EN AW-5754 | Hx2 | 132 | 23,7 | 595 | 645 | 70 | 32,5 |
| EN AW-5754 | Hx4 | 132 | 23,7 | 595 | 645 | 70 | 32,5 |
| EN AW-5754 | Hx6 | 132 | 23,7 | 595 | 645 | 70 | 32,5 |
| EN AW-5754 | Hx8 | 132 | 23,7 | 595 | 645 | 70 | 32,5 |
| EN AW-5754 | Hx9 | 23,7 | 595 | 645 | 70 | ||
| EN AW-5754 | O | 132 | 23,7 | 595 | 645 | 70 | 32,5 |
| Aluminium 5083 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.4 | 0.4 | 4.0 - 4.9 | 0.4 - 1.0 | 0.1 | 0.25 | 0.15 | Bal |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| O (annealed) | 42 | 21 | 14 |
| H112 | 43 | 23 | 10 |
| H116 | 46 | 33 | 10 |
| H321 | 46 | 33 | 10 |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| O (annealed) | 42 | 21 | 14 |
| H112 | 43 | 23 | 10 |
| H116 | 46 | 33 | 10 |
| H321 | 46 | 33 | 10 |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| T451 | 35 | 21 | 25 |
| T651 | 45 | 40 | 17 |
| Temper | Tensile | Hardness | ||||
|---|---|---|---|---|---|---|
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T5, T52 | 27 | 186 | 21 | 145 | 12 | 60 |
| T6 | 35 | 241 | 31 | 214 | 12 | 73 |
| Material | Diameter (mm) | Tensile Strength min (N/mm²) | Yield Strength min (N/mm²) | Elongation on 5.65v % (min) |
| Alloy 6082 T6 Bar | < 20 | 295 | 255 | 8 |
| Alloy 6082 T6 Bar | 20 - 150 | 310 | 270 | 8 |
| Alloy 6082 T6 Bar | 150 - 200 | 280 | 240 | 5 |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 7050 (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 7050 (AMS 4342) | T74511 | 73 | 63 | 7 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Mechanical Properties - Al 1060 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
| H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
| H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
| H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
| H18 | 130 | --- | 3 | 3 | 3 | ||||||||||||||
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
| Poisson's Ratio | 0.27-0.30 | 25 | |
| Elastic Modulus (GPa) | 190-210 | 25 | |
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
| Yield Strength (Mpa) | 495 | ||
| Elongation (%) | 10 | ||
| Reduction in Area (%) | 45 | ||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Thermal Expansion (10-6/ºC) | 11.8 | 0-100 more | rolled |
| Mechanical Properties - AA 1100 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1100 | O | 75 | 110 | 20 | 25 | 29 | |||||||||||||
| H12 | 95 | 130 | 5 | 6 | 7 | ||||||||||||||
| H14 | 110 | 145 | 3 | 4 | 5 | ||||||||||||||
| H16 | 130 | 165 | 2 | 3 | 4 | ||||||||||||||
| H18 | 150 | --- | 2 | 2 | 3 | ||||||||||||||
| Material | Temper | Diameter (mm) | Tensile Strength min ((N/mm²) | Yield Strength (min) (N/mm²) | Elongation on 5.65 V (min) |
| 2014 Bar | T4 | <20 | 370 | 230 | 11 |
| 2014 Bar | T4 | 20-75 | 390 | 250 | 11 |
| 2014 Bar | T4 | 75-150 | 390 | 250 | 9 |
| 2014 Bar | T4 | 150-200 | 370 | 230 | 8 |
| 2014 Bar | T6510 | 20-75 | 480 | 435 | 7 |
| 2014 Bar | T6510 | 75-150 | 465 | 420 | 7 |
| 2014 Bar | T6510 | 150-200 | 435 | 390 | 7 |
| Typical Mechanical Properties (Min) | ||||||||||
| Diameter or minor sectional dimension mm | Tensile Strength, MPa | Yield Strength 0.2%, MPa | Elongation % | |||||||
| 0-12.7 | 427 | 310 | 10 | |||||||
| 12.7-114.30 | 427 | 290 | 10 | |||||||
| 114.30-165.1 | 427 | 276 | 10 | |||||||
| 165.1-203.2 | 400 | 262 | 10 | |||||||
| Mechanical Properties - AA 3003 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 3003 | O | 95 | 135 | 20 | 23 | 24 | |||||||||||||
| H12 | 115 | 160 | 6 | 7 | 8 | ||||||||||||||
| H14 | 140 | 180 | 4 | 4 | 5 | ||||||||||||||
| H16 | 165 | 205 | 3 | 3 | 4 | ||||||||||||||
| H18 | 180 | --- | 2 | 2 | 3 | ||||||||||||||
| Mechanical Properties - AA 5005 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 5005 | O | 95 | 135 | 20 | 23 | 24 | |||||||||||||
| H12 | 115 | 160 | 6 | 7 | 8 | ||||||||||||||
| H14 | 140 | 180 | 4 | 4 | 5 | ||||||||||||||
| H16 | 165 | 205 | 3 | 3 | 4 | ||||||||||||||
| H18 | 180 | --- | 2 | 2 | 3 | ||||||||||||||
| Aluminium 5052 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.15 - 0.40 | 0.10 - 0.25 | 2.20 - 2.80 | 0.01 - 0.10 | 0.01 - 0.10 | 0.01 - 0.10 | 0.020 - 0.030 | 97.2 |
| Mechanical Properties - AA 5052 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 5052 | O | 171 | 213 | 16 | 18 | 19 | |||||||||||||
| H12 | 213 | 261 | 5 | 7 | 9 | ||||||||||||||
| H14 | 233 | 281 | 4 | 6 | 7 | ||||||||||||||
| H16 | 254 | 302 | 3 | 4 | 4 | ||||||||||||||
| H18 | 268 | - | 3 | 4 | 4 | ||||||||||||||
| Aluminium 5083 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.4 | 0.4 | 4.0 - 4.9 | 0.4 - 1.0 | 0.1 | 0.25 | 0.15 | Bal |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| O (annealed) | 42 | 21 | 14 |
| H112 | 43 | 23 | 10 |
| H116 | 46 | 33 | 10 |
| H321 | 46 | 33 | 10 |
| Aluminium 5086 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.5 | 0.4 | 3.5 - 4.5 | 0.2 - 0.7 | 0.1 | 0.25 | 0.15 | 95.4 |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| O (annealed) | 42 | 21 | 14 |
| H112 | 43 | 23 | 10 |
| H116 | 46 | 33 | 10 |
| H321 | 46 | 33 | 10 |
| Aluminium 6061 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.70 | 0.40 - 0.80 | 0.80 - 1.20 | 0.15 | 0.15 - 0.40 | 0.25 | 0.15 | 97.9 |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| T451 | 35 | 21 | 25 |
| T651 | 45 | 40 | 17 |
| Aluminium 6063 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.35 | 0.20 - 0.60 | 0.45 - 0.90 | 0.10 | 0.10 | 0.10 | 0.10 | 97.5 |
| Temper | Tensile | Hardness | ||||
|---|---|---|---|---|---|---|
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T5, T52 | 27 | 186 | 21 | 145 | 12 | 60 |
| T6 | 35 | 241 | 31 | 214 | 12 | 73 |
| Aluminium 6082 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.5 | 0.7 - 1.3 | 0.6 - 1.2 | 0.4 - 1.0 | 0.1 | 0.2 | 0.1 | Bal |
| Material | Diameter (mm) | Tensile Strength min (N/mm²) | Yield Strength min (N/mm²) | Elongation on 5.65v % (min) |
| Alloy 6082 T6 Bar | < 20 | 295 | 255 | 8 |
| Alloy 6082 T6 Bar | 20 - 150 | 310 | 270 | 8 |
| Alloy 6082 T6 Bar | 150 - 200 | 280 | 240 | 5 |
| Aluminium 6083 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.5 | 0.7 - 1.3 | 0.6 - 1.2 | 0.4 - 1.0 | 0.1 | 0.2 | 0.1 | Bal |
| Material | Diameter (mm) | Tensile Strength min (N/mm²) | Yield Strength min (N/mm²) | Elongation on 5.65v % (min) |
| Alloy 6083 T6 Bar | < 20 | 295 | 255 | 8 |
| Alloy 6083 T6 Bar | 20 - 150 | 310 | 270 | 8 |
| Alloy 6083 T6 Bar | 150 - 200 | 280 | 240 | 5 |
| Aluminium 7075 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.5 | 0.4 | 2.1 - 2.9 | 0.3 | 1.2 - 2 | 5.1 - 6.1 | 0.2 | 90 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Aluminium 1060 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.15 - 0.20 | 0.10 - 0.15 | 0.01 - 0.03 | 0.01 - 0.03 | 0.01 - 0.05 | 0.01 - 0.03 | 0.020 - 0.030 | 99.60 |
| Mechanical Properties - Al 1060 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
| H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
| H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
| H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
| H18 | 130 | --- | 3 | 3 | 3 | ||||||||||||||
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
| 2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 | Balance |
| Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
| 80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
| Aluminium 5083 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.4 | 0.4 | 4.0 - 4.9 | 0.4 - 1.0 | 0.1 | 0.25 | 0.15 | Bal |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| O (annealed) | 42 | 21 | 14 |
| H112 | 43 | 23 | 10 |
| H116 | 46 | 33 | 10 |
| H321 | 46 | 33 | 10 |
| Aluminium 5086 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.5 | 0.4 | 3.5 - 4.5 | 0.2 - 0.7 | 0.1 | 0.25 | 0.15 | 95.4 |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| O (annealed) | 42 | 21 | 14 |
| H112 | 43 | 23 | 10 |
| H116 | 46 | 33 | 10 |
| H321 | 46 | 33 | 10 |
| Aluminium 6061 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.70 | 0.40 - 0.80 | 0.80 - 1.20 | 0.15 | 0.15 - 0.40 | 0.25 | 0.15 | 97.9 |
| Temper | Tensile Strength | Yield Strength | Elongation |
|---|---|---|---|
| KSI | KSI | % | |
| T451 | 35 | 21 | 25 |
| T651 | 45 | 40 | 17 |
| Material | Diameter (mm) | Tensile Strength min (N/mm²) | Yield Strength min (N/mm²) | Elongation on 5.65v % (min) |
| Alloy 6082 T6 Bar | < 20 | 295 | 255 | 8 |
| Alloy 6082 T6 Bar | 20 - 150 | 310 | 270 | 8 |
| Alloy 6082 T6 Bar | 150 - 200 | 280 | 240 | 5 |
| Aluminium 7050 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.15 | 0.12 | 1.9 - 2.6 | 0.1 | 2 - 2.6 | 5.7 - 6.7 | 0.06 | 89 |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 7050 (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 7050 (AMS 4342) | T74511 | 73 | 63 | 7 |
| Aluminium 7075 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.5 | 0.4 | 2.1 - 2.9 | 0.3 | 1.2 - 2 | 5.1 - 6.1 | 0.2 | 90 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Aluminium 1060 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.15 - 0.20 | 0.10 - 0.15 | 0.01 - 0.03 | 0.01 - 0.03 | 0.01 - 0.05 | 0.01 - 0.03 | 0.020 - 0.030 | 99.60 |
| Mechanical Properties - Al 1060 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
| H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
| H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
| H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
| H18 | 130 | --- | 3 | 3 | 3 | ||||||||||||||
| Aluminium 1070 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.25 | 0.2 | 0.03 | 0.03 | 0.03 | 0.07 | 0.03 | 99.70 |
| Mechanical Properties - Al 1070 | |||||||||||||||||||
| Properties | Conditions | ||||||||||||||||||
| T (°C) | Treatment | ||||||||||||||||||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |||||||||||||||||
| Poisson's Ratio | 0.27-0.30 | 25 | |||||||||||||||||
| Elastic Modulus (GPa) | 190-210 | 25 | |||||||||||||||||
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more | ||||||||||||||||
| Yield Strength (Mpa) | 495 | ||||||||||||||||||
| Elongation (%) | 10 | ||||||||||||||||||
| Reduction in Area (%) | 45 | ||||||||||||||||||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more | ||||||||||||||||
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other Each | Other Total |
| Bal. | 0.20-0.8 | 0.7 max | 3.5-4.5 | 0.40-1.0 | 0.40-0.8 | 0.10 max | 0.25 max | 0.15 max | 0.05 max | 0.15 max |
| Material | Condition | Tensile Strength (N/mm²) min | Yield Strength | Elongation in 4D % | ||
| ksi | Mpa | ksi | Mpa | |||
| Al 2017 | 2017-T4 Bar | 55 | 379 | 32 | 221 | 12 |
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
| min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
| max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| (annealed) | 32 | 14 | 12 |
| T3 | 63 | 42 | 15 |
| Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
| Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
| Properties | Metric | Imperial |
| Tensile strength | 130 MPa | 18855 psi |
| Yield strength | 125 MPa | 18130 psi |
| Shear strength | 83 MPa | 12039 psi |
| Fatigue strength | 55 MPa | 7977 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Elongation | 10% | 10% |
| Hardness | 35 | 35 |
|
Element |
% |
Element |
% |
|
Aluminium |
Balance |
Manganese |
0.20 max |
|
Magnesium |
0.50 – 1.10 |
Chromium |
0.10 max |
|
Silicon |
0.30max |
Zinc |
0.25 max |
|
Iron |
0.07 max |
Others, each |
0.05 max |
|
Copper |
0.20 max |
Others, total |
0.15 max |
|
Temper |
0.2% Proof Stress, MPa min† |
Tensile Strength, MPa |
Elongation % min‡ |
|
O (annealed) |
35 |
105 – 145 |
12 – 22 |
|
H12 |
95 |
125 – 165 |
2 – 8 |
|
H14 |
115 |
145 – 185 |
1 – 6 |
|
H16 |
135 |
165 – 205 |
1 – 3 |
|
H18 |
– |
> 185 |
1 – 3 |
|
H32 |
85 |
115 – 160 |
3 – 9 |
|
H34 |
105 |
135 – 180 |
2 – 7 |
|
H36 |
125 |
160 – 200 |
1 – 4 |
|
H38 |
– |
> 180 |
1 – 4 |
| Al | Si | Fe | Cu | Mn | Cr | Mg | Ti | Zn | Other Each | Others Total |
| Bal | 0.40 max | 0.40 max | 0.10 max | 0.40 / 1.0 | 0.05 / 0.25 | 4.0 / 4.90 | 0.15 max | 0.25 max | 0.05 max | 0.15 max |
| Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
| 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
| Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Other Each | Others Total | Al |
| .10 (max) | .20/.60 | .35 (max) | .10 (max) | .45/.90 | .10 (max) | .10 (max) | .10 (max) | .05 | .015 | Remainder |
| Tensile Strength (psi) | Yield Strength (psi) | Elongation (% in 2") | Brinell Hardness |
| 27,000 | 21,000 | 12 | 60 |
| Weight % | Zn | Cu | Mg | Zr | Fe | Si | Mn | Ti | Cr | Others (total) |
| Minimum | 5.7 | 2.0 | 1.9 | 0.08 | - | - | - | - | - | - |
| Maximum | 6.7 | 2.6 | 2.6 | 0.15 | 0.15 | 0.12 | 0.10 | 0.06 | 0.04 | 0.15 |
| Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
| Aluminium Alloy 7050 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
| Aluminium Alloy 7050 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
| Aluminium Alloy 7050 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
| Weight % | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Each | Total |
| Minimum | 1.20 | 2.10 | 0.18 | 5.10 | ||||||
| Maximum | 0.40 | 0.50 | 2.00 | 0.30 | 2.90 | 0.28 | 6.10 | 0.20 | 0.05 | 0.15 |
| Temper | Tensile | Hardness | ||||
| Ultimate | Yield | Elongation | Brinell | |||
| KSI | MPA | KSI | MPA | % | ||
| T6, T651 | 83 | 572 | 73 | 503 | 11 | 150 |
| T73, T7351 | 73 | 503 | 63 | 434 | 13 | N/A |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||||
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Aluminium 1060 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.15 - 0.20 | 0.10 - 0.15 | 0.01 - 0.03 | 0.01 - 0.03 | 0.01 - 0.05 | 0.01 - 0.03 | 0.020 - 0.030 | 99.60 |
| Mechanical Properties - Al 1060 | |||||||||||||||||||
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
| H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
| H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
| H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
| H18 | 130 | --- | 3 | 3 | 3 | 23 | |||||||||||||
| Aluminium 1070 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.25 | 0.2 | 0.03 | 0.03 | 0.03 | 0.07 | 0.03 | 99.70 |
| Properties | Conditions | ||
| T (°C) | Treatment | ||
| Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
| Poisson's Ratio | 0.27-0.30 | 25 | |
| Elastic Modulus (GPa) | 190-210 | 25 | |
| Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
| Yield Strength (Mpa) | 495 | ||
| Elongation (%) | 10 | ||
| Reduction in Area (%) | 45 | ||
| Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Aluminium 2014 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.7 | 0.50 - 1.20 | 0.2 - 0.8 | 0.4 - 1.2 | 3.9 - 5.0 | 0.25 | 0.15 | 93.5 |
| Material | Temper | Diameter (mm) | Tensile Strength min ((N/mm²) | Yield Strength (min) (N/mm²) | Elongation on 5.65 V (min) |
| 2014 Pipes | T4 | <20 | 370 | 230 | 11 |
| 2014 Pipes | T4 | 20-75 | 390 | 250 | 11 |
| 2014 Pipes | T4 | 75-150 | 390 | 250 | 9 |
| 2014 Pipes | T4 | 150-200 | 370 | 230 | 8 |
| 2014 Pipes | T6510 | 20-75 | 480 | 435 | 7 |
| 2014 Pipes | T6510 | 75-150 | 465 | 420 | 7 |
| Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other Each | Other Total |
| Bal. | 0.20-0.8 | 0.7 max | 3.5-4.5 | 0.40-1.0 | 0.40-0.8 | 0.10 max | 0.25 max | 0.15 max | 0.05 max | 0.15 max |
| Material | Condition | Tensile Strength (N/mm²) min | Yield Strength | Elongation in 4D % | ||
| ksi | Mpa | ksi | Mpa | |||
| Al 2017 | 2017-T4 Bar | 55 | 379 | 32 | 221 | 12 |
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
| min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
| max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
| Temper | Tensile Strength | Yield Strength | Elongation |
| KSI | KSI | % | |
| (annealed) | 32 | 14 | 12 |
| T3 | 63 | 42 | 15 |
| Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
| Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
| Properties | Metric | Imperial |
| Tensile strength | 130 MPa | 18855 psi |
| Yield strength | 125 MPa | 18130 psi |
| Shear strength | 83 MPa | 12039 psi |
| Fatigue strength | 55 MPa | 7977 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Elongation | 10% | 10% |
| Hardness | 35 | 35 |
| GRADE | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Al |
| 5052 | 0.50 | 0.50 | 3.8/4.9 | 0.30/0.9 | 1.2/1.8 | 0.10 | 0.25 | 0.15 | Balance |
| Mechanical Property | Hardness, Brinell | Poisson's Ratio | Melting Point | Electrical Resistivity | Modulus of Elasticity | Specific Heat |
| Value | 47 | 0.33 | 607 - 649 °C | 4.99e-006 ohm-cm | 70.3 GPa | 0.88 J/g-°C |
| Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
| 2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 | Balance |
| Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
| 80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
| Weight% | Al | Si | Fe | Cu | Mn | Cr | Mg | Ti | Zn | Other Each | Others Total |
| 5083 | Bal | 0.40 max | 0.40 max | 0.10 max | 0.40 / 1.0 | 0.05 / 0.25 | 4.0 / 4.90 | 0.15 max | 0.25 max | 0.05 max | 0.15 max |
| Properties | Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
| Metric | 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
| Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Other Each | Others Total | Al |
| .10 (max) | .20/.60 | .35 (max) | .10 (max) | .45/.90 | .10 (max) | .10 (max) | .10 (max) | .05 | .015 | Remainder |
| Tensile Strength (psi) | Yield Strength (psi) | Elongation (% in 2") | Brinell Hardness |
| 27,000 | 21,000 | 12 | 60 |
| Weight% | Al | Si | Fe | Cu | Mn | Cr | Mg | Zn | Ti | Other Each | Others Total |
| Aluminium 6082 | Bal | 0.7 - 1.3 | 0.50 max | 0.10 max | 0.40-1.00 | 0.25 max | 0.06-1.20 | 0.20 max | 0.10 max | 0.05 max | 0.15 max |
| Diameter or minor sectional dimension mm | Tensile Strength, MPa | Yield Strength 0.2%, MPa | Elongation % |
| 0-20 | 295 | 255 | 8 |
| 20-150 | 310 | 270 | 8 |
| 150-200 | 280 | 240 | 5 |
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Alloy | Mn | Si | Cr | Cu | Fe | Zn | Al | Mg | Ti | Other Each/Total |
| 6061 | 0.15 | 0.4-0.8 | 0.15-0.35 | 0.15-0.4 | 0.7 | 0.25 | Remainder | 0.8-1.2 | 0.15 | 0.005/0.15 |
|---|
| Tensile Strengtd (PSI) | Yield Strengtd (PSI) | Shear Strengtd (PSI) | Elongation in 2″ | Brinell Hardness |
| 45,000 | 40,000 | 31,000 | 12 | 95 |
| Alloy | Al | Si | Fe | Cu | Mn | Cr | Mg | Zn | Ti | Other Each | Others Total |
| Aluminium 6082 | Bal | 0.7 - 1.3 | 0.50 max | 0.10 max | 0.40-1.00 | 0.25 max | 0.06-1.20 | 0.20 max | 0.10 max | 0.05 max | 0.15 max |
| Material | Diameter (mm) | Tensile Strength min (N/mm²) | Yield Strength min (N/mm²) | Elongation on 5.65v % (min) |
| Alloy 6082 | < 20 | 295 | 255 | 8 |
| 20 - 150 | 310 | 270 | 8 | |
| 150 - 200 | 280 | 240 | 5 |
| Alloy | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Each | Total | ||||||||||
|
Aluminium 7075 |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | 0.40 | - | 0.50 | 1.20 | 2.00 | - | 0.30 | 2.10 | 2.90 | 0.18 | 0.28 | 5.10 | 6.10 | - | 0.20 | - | 0.05 | - | 0.15 | |
| Standard | Temper | Tensile | Hardness | ||||
| Aluminium 7075 | Ultimate | Yield | Elongation | Brinell | |||
| T6, T651, T6511 | KSI | MPA | KSI | MPA | % | ||
| 83 | 572 | 73 | 503 | 11 | 150 | ||
| 73 | 503 | 63 | 434 | 13 | N/A | ||
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
|
Alloy (ISS) |
Equivalent alloy (A.A) |
Copper |
Magnesium |
Silicon | Iron | Managanese Others* (Total) | Remarks | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Old | New |
U.S.A |
Min. | Max. | Min. | Max. | Min. | Max. | Min. | Max. | Max | Max. | Aluminum 99.0% Min. | ||
| 1 B | 19500 | 1050 | — | 0.05 | — | — | — | 0.30 | 0.4 | — | 0.05 | 0.1 | Aluminum 99.5% Min. | ||
| Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
|---|---|---|---|---|---|---|
| Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) | ||
| EN AW-1050 A | F | 60 | – | 20 | – | 23 |
| O | 60 | 95 | 20 | – | 23 | |
| Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Each | AI |
| 1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 | 99.60% |
| 1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 | remainder |
| Alloy | Temper | UTS(Mpa) | % Elongation | |||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
| 1100 | O | 75 | 110 | 20 | 25 | 29 |
| H12 | 95 | 130 | 5 | 6 | 7 | |
| H14 | 110 | 145 | 3 | 4 | 5 | |
| H16 | 130 | 165 | 2 | 3 | 4 | |
| H18 | 150 | --- | 2 | 2 | 3 | |
| Aluminium 2014 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.7 | 0.50 - 1.20 | 0.2 - 0.8 | 0.4 - 1.2 | 3.9 - 5.0 | 0.25 | 0.15 | 93.5 |
| Material | Temper | Diameter (mm) | Tensile Strength min ((N/mm²) | Yield Strength (min) (N/mm²) | Elongation on 5.65 V (min) |
| 2014 Bar | T4 | <20 | 370 | 230 | 11 |
| 2014 Bar | T4 | 20-75 | 390 | 250 | 11 |
| 2014 Bar | T4 | 75-150 | 390 | 250 | 9 |
| 2014 Bar | T4 | 150-200 | 370 | 230 | 8 |
| 2014 Bar | T6510 | 20-75 | 480 | 435 | 7 |
| 2014 Bar | T6510 | 75-150 | 465 | 420 | 7 |
| 2014 Bar | T6510 | 150-200 | 435 | 390 | 7 |
| Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Others Each | Other Total |
| 2017 | Rem | 0.20-0.8 | 0.7 max | 3.5-4.5 | 0.40-1.0 | 0.40-0.8 | 0.10 max | 0.25 max | 0.15 max | 0.05 max | 0.15 max |
| Material | Condition | Tensile Strength (N/mm²) min | Yield Strength | Elongation in 4D % | ||
| ksi | Mpa | ksi | Mpa | |||
| 2017 | 2017-T4 Bar | 55 | 379 | 32 | 221 | 12 |
| Aluminium 5052 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
| 0.15 - 0.40 | 0.10 - 0.25 | 2.20 - 2.80 | 0.01 - 0.10 | 0.01 - 0.10 | 0.01 - 0.10 | 0.020 - 0.030 | 97.2 |
| Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
| Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
| 5052 | O | 171 | 213 | 16 | 18 | 19 | |||||||||||||
| H12 | 213 | 261 | 5 | 7 | 9 | ||||||||||||||
| H14 | 233 | 281 | 4 | 6 | 7 | ||||||||||||||
| H16 | 254 | 302 | 3 | 4 | 4 | ||||||||||||||
| H18 | 268 | - | 3 | 4 | 4 | ||||||||||||||
| Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
| 2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 | Balance |
| Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
| 80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
Satish Bothra (Jagdish Metal)
226/06, 1st Floor, Sambhavdarshan Building Raja Ram Mohan Roy Marg, Prarthna Samaj, Mumbai - 400004, Khetwadi, Maharashtra
Share us via
