Rajkot, Gujarat, India
Our Products
Flame Hardened Bed WaysChuck PlateChange Gear Set (Inch & mm)Tool Post SpannerCenter AdaptorDead Center 2 no.Motor PulleyMotor Railing 2 no.
Face plateCarrier platesteady rest, follow rest, Taper turning attachmentmotorised coolant pump with tank and fittings, Rear tool post with extended cross slideChuck back plates (Extra)Electricals (Motor, Panel board, Wirings, Push button Switches, V-belts and fittings), Electrical Switch shaft and Splash guard
| MODEL | AGL – 4 | AGL – 6 |
|---|---|---|
| Admit Between Center | 660 mm | 1200 mm |
| Length of Bed | 1370 mm(4′-6″) | 1825 mm (6′) |
| Floor Space | 1500×850 | 1825 x 850 |
| Centre Height over flat bed ways : | 165 mm | 165 mm |
| Swing Over Bed : | 325 mm | 325 mm |
| Swing Over Cross Slide : | 175 mm | 175 mm |
| Swing in Gap : | 500 mm | 500 mm |
| Width of Bed | 225 mm | 225 mm |
| Type of Spindle Nose | Threaded |
| Spindle bore | 38 mm |
| Spindle Morse Taper | MT 5 |
| Spindle Adapter Morse Taper | MT 3 |
| Spindle Speeds | 8 |
| Nos. / RPM Range | 54 to 1200. RPM |
| Spindle Mounting on | Taper Roller Bearings |
| Spindle Diameter | 38.1 mm |
| Spindle Travel | 120 mm |
| Spindle Morse Taper | MT-3 |
| LEADING SCREW : Diameter / Threads : | 25.4 mm / 4 TPI |
| Nos. of Threads / Range metric | 17 / 0.5 mm To 15 mm Pitch |
| (For Fully norton Gearbox) inch | 40 / 2 to 60 TPI |
| Suitable Electric | |
| Electric motor of 2 HP / 1.5 k.w., 3 Phase, 1440 RPM | |
| Reverse – Forward Switch, V-belts and fittings. |
Flame Hardened Bed Ways
Chuck Plate
Change Gear Set ( Inch & mm )
Tool Post Spanner
Center Adaptor
Dead Center 2 no.
Motor Pulley
Motor Railing 2 no.
Face Plate
Steady Rest
| WIDTH OF BED 12.3/4″ (323 MM) | |||
|---|---|---|---|
| SPECIFICATION | 10″ Center Height | 12″ Center Height | Spindle Bore Avalible |
| Center Height | 254 mm | 304 mm | 2.1/8″ (54 mm) |
| Swing Over Bed | 458 mm | 580 mm | 3.1/8″ (80 mm) |
| Swing Over Cross Slide | 300 mm | 400 mm | 4.1/8″ ( 104 mm) |
| Swing In Gap Bed | 810 mm | 900 mm | 5.1/8″ (130 mm) |
| Width of Bed | 12.3/4″ (323 mm) | ||
| Length Of Bed | ABC | Approx Floor Space |
| 5′-6″ (1675 mm) | 525 mm | 2400 X 1300 X 1600 |
| 7′ (2135 mm) | 1000 mm | 2850 X 1300 X 1600 |
| 9′ (2745 mm) | 1600 mm | 3350 X 1300 X 1600 |
| 10′ (3050 mm) | 1900 mm | 3700 X 1300 X 1600 |
| 12′ (3660 mm) | 2500 mm | 4300 X 1300 X 1600 |
| 14′ (4270 mm) | 3120 mm | 5000 X 1300 X 1600 |
| 16′ (4875 mm) | 3730 mm | 5550 X 1300 X 1600 |
| 18′ (5485 mm) | 4340 mm | 6100 X 1300 X 1600 |
| Taper Bore In Spindle Sleeve | MT-4 | |
| Taper Bore In Main Spindle | MT-6 | |
| No. Of Spindle Speed | 8 | |
| Rpm (Low – High) | 28 to 520 RPM | |
| V-Belt | C-70 | |
| Metric Thread (mm) | 13 (1 TO 6 mm) | |
| British Thread (Inch) | 19 (2 TO 24 TPI) | |
| Lead Screw (O.D. & Tpi) | 1.5″ (38 mm) & 4 TPI | |
| Power | 3 Phase 1440 Rpm |
