JD series automatic mould temperature controller is mainly used to bring the mould to a specific operating temperature and hold that temperature constant by heating and/or cooling a Circulating fluid heat transfer medium. This series adopts heat-exchanging principle, using water or high-heat-conduction oil as transfer medium. Unstable temperature in the process of mould forming always tends to produce unqualified products. According to the principle of heat exchange, JD’s mould temperature controls make use of water and high property heat transferring oil as a medium to keep a proper stable temperature in the process of mould forming so as to guarantee high quality of products and raise the productive efficiency.   Features: Mould Temperature Controller – Hot medium liquid : Water or oil convertibility, Either water or oil can be used as a hot medium liquid according to the needs of mold forming temperature. Its high selectivity is certain to bring in high economic efficiency. While most of the MTC’s (Mould Temperature Controller) only support one medium, Our MTC (Mould Temperature Controller) supports both Water and Oil Medium. – Vertical Pump: The flow of vertical pump can be always kept steady, making its service life long and durable. – Stainless medium tank: Our Mould Temperature Controller’s interior tank will not get rust for long term, which is sure to prevent from any blockade of pipes and keep long-term service of pump. – Transparent water (oil) level viewer: The transparent water (oil) level viewer can easily be used to view and inspect the quantity of medium liquid and be reminded to refill the medium liquid from time to time. – Automatic alarming device: While water (oil) shortage occurs in the container, this device will automatically light up and start alarming and cut off the electric power of heaters and pumps, thus guaranteeing the machines (MTC) safety as well as the person running it. – High-precision automatic temperature control: The measure of temperature is very sensitive and accurate, little change of temperature helps to keep products both fine and delicate. – Minimize Products Wastage: The mold can reach the required temperature right at the beginning of operation, thus can obviously minimize products shortage. – Maintain proper temperature: Either in continuous operation or in temporary shutting down, mold-forming temperature can always be kept proper to guarantee the best quality of products and further improve the forming process.   – Compact in size, light in weight: Easy to install, convenient to operate, convenient to move and little room to occupy, our Mould Temperature Controller (MTC) is perfect choice for any Company running any kind of mould.

JD series Auto loader offer a wide choice of loader-blower sets and are designed for higher through puts from 250kg-1200kg. The unit are supplied with a separate 3-phase floor standing blower station which is low noise & maintenance free. JD units are also available with two material lines with a common blower & can cater two machine simultaneously. Imported high speed commutator motor, small cubage and strong suction. Connection between operation controller and electric control box free and convenient  operation. The micro computer controls and the accurate action.  Out hanged air storage device to thoroughly clean the dust on the strainer.   Features： – The Auto Loader’s main engine and the material hopper are designed separately and thus it is safe, easy and convenient to be operated. – The whole operation in Auto Loader is controlled by Microchip computer. – Equipped with an independent filter, Our Auto Loader is very convenient to clean up dust. – The equipped muffler reduces the noise in operation unlike any other Normal Auto Loader – Stainless steel material Auto Loader is light in weight, durable and very convenient for cleaning the device. – The control box being designed separately is easy to maintained. – Auto-buzzer will give alarm in-case of Leaking material or shortage. – Auto-protective device protects motor against overloading. – The bunker with electronic eye can be installed on the charging inlet of molding machine directly. – Can select two-material proportional valve, used for new material mixed Grinned material using or instant receiving of Grinned material. – Induction type motor of Auto Loader has strong suction force & long service life. – Independent filter, convenient for cleaning accumulated dust.

A silo is a tall tower with a cylindrical shape. The Silo holds anything that needs to stored in bulk. We have a high quality range of Silos available with us. Can be customized as per customers need. Sizes available.

We are eventual source for Granulators Knives. We provide them in various models well suited for various applications. High quality parts are so designed that they meet the demanding needs of the process and reduce the downtime.  

Our  Storage Racks  are especially designed by the expertise to fulfill various storage requirements of different industries. These racks are supervised by using the various parameters to ensure the effective quality. The finest raw material are used in the industry.  Widely used in warehouses and various industries for storage of materials, these systems are also checked on various parameters of quality. Features: Light weight Less maintenance Durable finish standard

We Offer Process Chillers for Plastic, Medical, Pharmaceutical industries and varied industrial applications like plastic mould cooling, printing and lamination processes. These chillers incorporate microprocessor based controls which offer intelligent cooling and are energy efficient apart from being extremely compact with a small footprint. Features – Wide range of models: 8, 11, 18, 26, 35, 45, 52 and 77 TR – Energy efficient scroll compressors and plate heat exchangers – Extremely compact plug-in design for high ambient applications – Stainless steel hydraulic circuit with buffer and expansion tank – Microprocessor controller with computer and remote connectivity – Anti-corrosive fins – Low noise – Food grade quality option available

JD series Auto loader offer a wide choice of loader-blower sets and are designed for higher through puts from 250kg-1200kg. The unit are supplied with a separate 3-phase floor standing blower station which is low noise & maintenance free. JD units are also available with two material lines with a common blower & can cater two machine simultaneously. Imported high speed commutator motor, small cubage and strong suction. Connection between operation controller and electric control box free and convenient  operation. The micro computer controls and the accurate action.  Out hanged air storage device to thoroughly clean the dust on the strainer.   Features： – The Auto Loader’s main engine and the material hopper are designed separately and thus it is safe, easy and convenient to be operated. – The whole operation in Auto Loader is controlled by Microchip computer. – Equipped with an independent filter, Our Auto Loader is very convenient to clean up dust. – The equipped muffler reduces the noise in operation unlike any other Normal Auto Loader – Stainless steel material Auto Loader is light in weight, durable and very convenient for cleaning the device. – The control box being designed separately is easy to maintained. – Auto-buzzer will give alarm in-case of Leaking material or shortage. – Auto-protective device protects motor against overloading. – The bunker with electronic eye can be installed on the charging inlet of molding machine directly. – Can select two-material proportional valve, used for new material mixed Grinned material using or instant receiving of Grinned material. – Induction type motor of Auto Loader has strong suction force & long service life. – Independent filter, convenient for cleaning accumulated dust.

        JD-Series vertical batch mixer is suitable for mixing of powder and granule material. The mixing can be finished quickly and completely. The ideal structure and design make it easy for operation, and also easy for cleaning and maintenance. It is mainly used for mixing and stirring of plastics material. Also it is widely used in the industry of powder metallurgy, pharmacy, chemicals, foodstuff, ceramic ware and so on. It is ideal for mixing.   Features： Vertical Batch Mixer • In our, Vertical Batch Mixer Both mixing pail and vane are made of stainless steel, easy to clean and absolutely no pollution. • The chain safety device can protect the safety of operator and machine. • The material in our Vertical Batch mixer is thick, strong and durable. • Well-distributed mixing can be done in a shot time, low energy consumption and high efficiency. • Time setting can be controlled easily and precisely in the range of 0-15 minutes. • Vertical design, less space occupied, easy dismounting

  Day bins are very adaptable and can be used for storing both raw materials and finished products. Available in different sizes.

JD series automatic mould temperature controller is mainly used to bring the mould to a specific operating temperature and hold that temperature constant by heating and/or cooling a Circulating fluid heat transfer medium. This series adopts heat-exchanging principle, using water or high-heat-conduction oil as transfer medium. Unstable temperature in the process of mould forming always tends to produce unqualified products. According to the principle of heat exchange, JD’s mould temperature controls make use of water and high property heat transferring oil as a medium to keep a proper stable temperature in the process of mould forming so as to guarantee high quality of products and raise the productive efficiency.   Features: Mould Temperature Controller – Hot medium liquid : Water or oil convertibility, Either water or oil can be used as a hot medium liquid according to the needs of mold forming temperature. Its high selectivity is certain to bring in high economic efficiency. While most of the MTC’s (Mould Temperature Controller) only support one medium, Our MTC (Mould Temperature Controller) supports both Water and Oil Medium. – Vertical Pump: The flow of vertical pump can be always kept steady, making its service life long and durable. – Stainless medium tank: Our Mould Temperature Controller’s interior tank will not get rust for long term, which is sure to prevent from any blockade of pipes and keep long-term service of pump. – Transparent water (oil) level viewer: The transparent water (oil) level viewer can easily be used to view and inspect the quantity of medium liquid and be reminded to refill the medium liquid from time to time. – Automatic alarming device: While water (oil) shortage occurs in the container, this device will automatically light up and start alarming and cut off the electric power of heaters and pumps, thus guaranteeing the machines (MTC) safety as well as the person running it. – High-precision automatic temperature control: The measure of temperature is very sensitive and accurate, little change of temperature helps to keep products both fine and delicate. – Minimize Products Wastage: The mold can reach the required temperature right at the beginning of operation, thus can obviously minimize products shortage. – Maintain proper temperature: Either in continuous operation or in temporary shutting down, mold-forming temperature can always be kept proper to guarantee the best quality of products and further improve the forming process.   – Compact in size, light in weight: Easy to install, convenient to operate, convenient to move and little room to occupy, our Mould Temperature Controller (MTC) is perfect choice for any Company running any kind of mould.

We Offer Process Chillers for Plastic, Medical, Pharmaceutical industries and varied industrial applications like plastic mould cooling, printing and lamination processes. These chillers incorporate microprocessor based controls which offer intelligent cooling and are energy efficient apart from being extremely compact with a small footprint. Features – Wide range of models: 8, 11, 18, 26, 35, 45, 52 and 77 TR – Energy efficient scroll compressors and plate heat exchangers – Extremely compact plug-in design for high ambient applications – Stainless steel hydraulic circuit with buffer and expansion tank – Microprocessor controller with computer and remote connectivity – Anti-corrosive fins – Low noise – Food grade quality option available

We provide our customers a premium quality range of PVC Pipes. These are manufactured using raw materials of the best quality. Different Sizes (Length and Breadth) available.