Write a Review
Our Products
Leading Manufacturer, Supplier & Retailer of Flute Rib Processing End Mills, Carbide Tipped Straight Shanked End Mill, Carbide End Mills, Flute Radius End Mills and Parallel Shank End Mills.
Features:
| For deep pocketing or deep reach Features | |
| Also avaialble in 4-Flute above 2mm diameter | |
| Designed with reinforced shank for higher stability | |
| Long neck design for deep machining near walls |
| Ordering No. | Flute Dia(D1) |
Flute Len(L2) |
Overall Len(L1) |
Shank Dia(D2) |
Reach Len(L2) |
Neck Dia(D3) |
||||||||
| 20901006-F | 1 | 2 | 50 | 4 | 6 | 0.95 | ||||||||
| 20901010-F | 1 | 2 | 50 | 4 | 10 | 0.95 | ||||||||
| 20901506-F | 1.5 | 2 | 50 | 4 | 6 | 1.45 | ||||||||
| 20901510-F | 1.5 | 2 | 50 | 4 | 10 | 1.45 | ||||||||
| 20902008-F | 2 | 3 | 50 | 4 | 8 | 1.95 | ||||||||
| 20902012-F | 2 | 3 | 50 | 4 | 12 | 1.95 | ||||||||
| 20902016-F | 2 | 3 | 50 | 4 | 16 | 1.95 | ||||||||
| 20902020-F | 2 | 3 | 50 | 4 | 20 | 1.95 | ||||||||
| 20902508-F | 2.5 | 4 | 50 | 4 | 8 | 2.4 | ||||||||
| We are the manufacturer and supplier of carbide tipped straight shank end mill in india |
| Sizes available 1/4" to 3"custom design can also be done |
Features:
| These end mills are meant for general purpose milling of Low carbon steel, M.S, softer Steels, Cast Iron up to 320BHN etc. | |
| These end mills are abvaialble in stock in STD, LONG, EXL lengths at all times. | |
| Size ranges from 1mm to 25mm up to a total length of 250mm are made on order basis. | |
| Dispatch in 1-day even the EXTRA LONG Series. |
| Ordering No. | Flute Dia(D1) |
Flute Len(L2) |
Overall Len(L1) |
Shank Dia(D2) |
|||||
| 201020038-F | 2 | 9 | 38 | 3 | |||||
| 201025038-F | 2.5 | 12 | 38 | 3 | |||||
| 201030038-F | 3 | 12 | 38 | 3 | |||||
| 201030050-F | 3 | 15 | 50 | 3 | |||||
| 201030075-F | 3 | 20 | 75 | 3 | |||||
| 201030100-F | 3 | 25 | 100 | 3 | |||||
| 201040050-F | 4 | 14 | 50 | 4 | |||||
| 201040075-F | 4 | 20 | 75 | 4 | |||||
| 201040100-F | 4 | 25 | 100 | 4 | |||||
| 201050050-F | 5 | 16 | 50 | 5 | |||||
| 201050075-F | 5 | 20 | 75 | 5 | |||||
| 201050100-F | 5 | 25 | 100 | 5 | |||||
| 201060050-F | 6 | 16 | 50 | 6 | |||||
Features:
| Carbide 6-Flute End Mills is mainly used for finishingapplication where stringent Ra values are required. | |
| Controlled Run-out & tolerance for finish machining | |
| Corner Radius to provide more edge strength | |
| More flutes means higher feed rates & more productivity |
| Ordering No. | Flute Dia(D1) |
Flute Len(L2) |
Overall Len(L1) |
Shank Dia(D2) |
Corner Radius (R) | |||||||
| 217060075R0.5-F | 6 | 25 | 75 | 6 | R0.5 | |||||||
| 217060075R1.0-F | 6 | 25 | 75 | 6 | R1.0 | |||||||
| 217080075R0.5-F | 8 | 25 | 75 | 8 | R0.5 | |||||||
| 217080075R1.0-F | 8 | 25 | 75 | 8 | R1.0 | |||||||
| 217080075R1.5-F | 8 | 25 | 75 | 8 | R1.5 | |||||||
| 217100075R0.5-F | 10 | 30 | 75 | 10 | R0.5 | |||||||
| 217100075R1.0-F | 10 | 30 | 75 | 10 | R1.0 | |||||||
| 217100075R1.5-F | 10 | 30 | 75 | 10 | R1.5 | |||||||
| 217120075R1.0-F | 12 | 30 | 75 | 12 | R1.0 | |||||||
Features:
| Carbide High Helix End Mills are especially used asaluminum finisher, | |
| Higher Helix for low power consumption | |
| Available with Corner Radius upon request |
| Ordering No. | Flute Dia(D1) |
Flute Len(L2) |
Overall Len(L1) |
Shank Dia(D2) |
|||||
| 211040050-U | 4 | 14 | 50 | 4 | |||||
| 211040075-U | 4 | 25 | 75 | 4 | |||||
| 211040100-U | 4 | 30 | 100 | 4 | |||||
| 211050050-U | 5 | 16 | 50 | 5 | |||||
| 211050075-U | 5 | 25 | 75 | 5 | |||||
| 211050100-U | 5 | 35 | 100 | 5 | |||||
| 211060050-U | 6 | 18 | 50 | 6 | |||||
| 211060075-U | 6 | 30 | 75 | 6 | |||||
| 211060100-U | 6 | 35 | 100 | 6 | |||||
| 211080060-U | 8 | 20 | 60 | 8 | |||||
| 211080100-U | 8 | 40 | 100 | 8 | |||||
| 211100075-U | 10 | 30 | 75 | 10 | |||||
| 211100100-U | 10 | 50 | 100 | 10 | |||||
Mohammed Bhai (Kb Industries)
F-404, Sarvoday Shrishti, Wing 3, Near Raheja Complexes Kalyan West, Thane, Mumbai, Maharashtra - 421301
Share us via
