Working load limit (WLL) 1500 - 5000kgsThis range of horizontal plate clamps has been designed, to be used in pairs, for the horizontal transporting of individual and bundled plate. Whilst the basic design and function is the same, there are four options available.OPTION 1 - RH. This range is fitted with a steel roller for reduced marking of the plates.OPTION 2 - WH. The jaw on this range has hardened steel teeth for applications where the marking of plates is not an issue.OPTION 3 - WHL. With a protective rubber lining on the jaw and the toe plate, this range totally eliminates any risk of marking.OPTION 4 - WHP. With a protective polyurethane coating completely encasing the jaw and the toe plate.

The TTG girder clamps are designed for transporting girders in the 'I' configuration position (see photograph on the right).These are ideal for use within steel stockholders. Once offered up to the horizontal flange of the girder they are locked in place by the jaw locking lever.The design allows the clamp to be used individually, however for longer girders they should be used in pairs in conjunction with a spreader beam

The TSZ 'two way' screw clamps have all the same features of the TSD (shown above) but have the additional benefit of a second lifting point enabling it to pull in two different directions.NB. The plate surface of the material to be lifted must not exceed a hardness level of HRC 30Brinell 300.

Working load limit (WLL) 1000 - 30000kgsThese clamps are primarily used for transporting sheet metal and steel plates in the vertical position, as well as lifting and rotating through 180'. They can also be used for transporting steel constructions and profiles. It is recommended to use a pair of plate clamps in conjunction with a spreader beam for long materials which have a tendency to sag or flex. Function The jaw is opened and closed with the locking lever. The safety lock spring loads the cam jaw, preventing the clamp from opening even when there is no load. Workmanship and parts These plate clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person. NB: The plate surface of the material must have a hardness level below HRC 30Brinell 300.

The CY plate clamps with hinged hook rings can be used for the safe handling of plate at various angles. It can lift plate from the horizontal and put down in the vertical. The hinged hook ring ensures adequate gripping pressure in every position, but the load capacity is reduced as seen in the diagram below showing the load force capacities. The main benefit of the CY hinged plate clamps is that longer plates can be lifted or handled, using two clamps on a two legged chain sling (as shown in illustration), thus eliminating the need for a spreader beam. NB: The plate surface of the material must have a hardness level below HRC 30Brinell 300.

Standard plate clamps with safety lock working load limit (WLL) 500 - 3000kgs These clamps are primarily used for transporting sheet metal and steel plates in the vertical position, as well as lifting and rotating through 1800. They can also be used for transporting steel constructions and profiles. It is recommended to use a pair of plate clamps in conjunction with a spreader beam for long materials which have a tendency to sag or flex. Function The jaw is opened and closed with the locking lever except for the 92-500 which uses a positive spring-loaded cam. The safety lock spring loads the cam jaw, preventing the clamp from opening even when there is no load.

The TSB non-marking plate clamps with chain are designed for vertical lifting and transporting of plate material. This particular range of clamps has a large jaw capacity that enables it to be used on a multitude of applications.The main feature of the TSB plate clamps is the fact that it is non-marking. It works through the process of 'friction'. This is achieved by a special material on the jaw and pad which is similar to brake linings.Other benefits of the TSB, is that one grab can also be used for lifting materials such as concrete, wood, stone, and hardened steel.

The TAG universal clamps are extremely versatile. They have a large jaw capacity that enables them to be used on a multitude of applications such as loading machine tools, steel constructions, welding and numerous assembly duties. The design means that they do not require additional chain slings and are very easy and simple to use. The automatic gripping force is retained by a positive tension jaw spring, even if there is slack in the chain. The clamps are also fitted with a 'Quick-Open' lever for ease of loading and unloading. These clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person. Protective lined jaws can be fitted up to 1250kgs WLL.

The main purpose of the CG girder turning clamps is for the transportation and turning of steel girders (RSJ) through 900 degrees.They can be used individually or for longer beams used in pairs in conjunction with a spreader beam as shown in diagram.The clamps are attached to the horizontal flange of the girder and locked in place by the jaw locking lever. Once lifted the girder will turn through 900 degrees.

Designed for hardened material. Working load limit (WLL) 500 - 4000kgs HG plate clamps have an extremely high clamping force which makes the clamps particulars suited to the transport of plate with a surface hardness up to HRC 40Brinell 375. Function These clamps are opened and closed with a locking lever. The safety lock spring loads the cam jaw, preventing the clamp from opening even when there is no load. Workmanship and parts These plate clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person.

The LJ non-marking plate clamps are designed for lifting, turning and transporting of all structural steel plates, stainless steel, iron, timber and aluminium without marking, damaging or leaving indentations on the surface. It can also be used for plates with extremely hard surfaces.As standard these clamps come with leather lined pads and jaws, however there is also the option of having rubber or plastic pads fitted for use with polished materials. Contact our sales team for details.These plate clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person. NB: The surface of the plate must be free of oil, grease or any other liquid to ensure safe transport.

The SCB bulb bar clamp is a variant of Camlok's SCA clamp and is particularly useful in the ship building industry. The clamp has a large bow shackle for quick and easy attachment of hoist slings etc. Also available with load bar for low headroom.

The TSH 'swivel hook' screw clamps offer many possible applications. It is particularly useful for lifting, transferring and pulling sheet metal, girders and steel constructions.The clamps are supplied complete with an alloy safety shackle, that allows for pulling in 180' degrees.NB. The plate surface of the material to be lifted must not exceed a hardness level of HRC 30Brinell 300.

The THK horizontal plate clamps share the same basic design features as the CH range of clamps but have a reversed tooth jaw design. This acts as an additional safety feature specifically for use with thin sheets which may have a tendency to deflect or sag or flex.The THK clamps are particularly suited to thin plate with a surface hardness less than 300 Brinell 32 Rockwell C.

TPZ board clamps offer an simple and effective way to vertically lift and transport a variety of materials such as wood, MDF, plasterboard, stone, and plastics. They can also be used to lift loads from the horizontal to the vertical through 900 for transportation. The range has been designed to be user friendly and the handle enables the operator to guide the load easily during operation and each clamp is supplied fitted with large rubber pads to minimise damage.These clamps are ideal in production facilities and especially on construction and building sites.

Working load limit (WLL) 1500 - 3000kgs*The BTG concrete pipe lifting clamps are sold in sets of three and they come complete with chain slings (the working load limits shown are based on a set of three clamps).They are designed for the vertical transportation of concrete pipe sections with a diameter of up to 2000mm.The jaw capacity is designed for pipe thickness of 40 - 200mm.Attachment and removal of the clamps from the pipes is extremely easy due to the simple and straightforward design.

The SCA screwlok beam clamps offer many of the same features as our other beam clamps however this range is specifically designed to be attached to rolled steel angle. These are normally found against the wall of a roof.

The HGC hand grip clamps are suited for the individual transport of light and thin plates. They have a jaw capacity of up to 10 mm and can lift up to 250kgs.To operate the clamp you simply press down on the hand grip which compresses a spring. This allows the clamp to open and slide onto the plate. The plate can then be lifted and transported using the ergonomically designed hand grip. The positive spring pressure prevents the plate from accidentally slipping out of the clamp.NB. Plate surface of material lifted must not exceed a hardness level of HRC 30Brinell 300.

Camlok have now designed a brand new range of reinforced beam clamps. The YRC clamps have all the standard features associated with the SC range of clamps but have the added benefit of being extremely tough and robust, due to the reinforced side plates and jaws.This design change makes them a very safe attachment point, even under demanding conditions.

The SCS screwlok beam clamps have been specifically designed for use as a semi-permanent anchor point.This range is fitted with swivel jaws that a give a more positive grip to the beam flange.These clamps are fitted with a shackle suspension point and are very quick and easy to attach to the beam by simply turning the threaded middle bar.

The THS horizontal plate clamps are specifically designed to be used whenloading plate horizontally into presses, shears, guillotines and other industrial machines or where the CH clamps are not suitable.The unique design of the THS allows them to be used individually when loadingplate. However, when transporting plate horizontally the THS clamps should be used in pairs.Other features of this clamp include a spring loaded safety lock that ensures the clamp remains on the plate in the unloaded position prior to lifting.Maximum plate surface hardness 300 Brinell 32 Rockwell C.

The SC92 beam clamp provides a quick and versatile rigging point for hoisting equipment, pulley blocks or loads. The unit offers flexible applications, due to the wide adjustment range. The central threaded spindle allows easy attachment and a safe and secure grip to the beam flange.NB. THIS MODEL MUST NOT BE USED FOR LIFTING.

The SC beam clamp provides a quick and versatile rigging point for hoisting equipment, pulley blocks or loads and comes complete with a locking device.The unit offers flexible applications, due to the wide adjustment range. The central threaded spindle allows easy attachment and a safe and secure grip to the beam flange.NB. THIS MODEL MUST NOT BE USED FOR LIFTING.

The ACH horizontal plate clamps offer superb flexibility because of the large adjustable jaw opening. The jaw is adjusted using a simple ratchet mechanism.These clamps are to be used in pairs and are especially suited to the transportation of large plate bundles

Heavy duty - side loading The CX plate clamps shares all the benefits of the CY clamps, but are specifically designed for more heavy duty applications. The other benefit that the CX clamps offers over the CY clamps is that vertically racked plates can be turned through 90 (as shown in illustration) NB: The plate surface of the material must have a hardness level below HRC 30Brinell 300.

The TSD standard screw clamps offer many possible uses. They are designed to be used in conjunction with ratchet lever hoists to align steel structures or fabrications. They are ideally suited for the construction industry. The unique design of the spindle makes it easy to attach to 'angle' plate. This is achieved by simply turning the handle which applies the pressure to the plate holding it securely. NB. The plate surface of the material to be lifted must not exceed a hardness level of HRC 30Brinell 300

Working load limit (WLL) 1500 - 5000kgsThis range of horizontal plate clamps has been designed, to be used in pairs, for the horizontal transporting of individual and bundled plate. Whilst the basic design and function is the same, there are four options available.OPTION 1 - RH. This range is fitted with a steel roller for reduced marking of the plates.OPTION 2 - WH. The jaw on this range has hardened steel teeth for applications where the marking of plates is not an issue.OPTION 3 - WHL. With a protective rubber lining on the jaw and the toe plate, this range totally eliminates any risk of marking.OPTION 4 - WHP. With a protective polyurethane coating completely encasing the jaw and the toe plate.

The TTG girder clamps are designed for transporting girders in the 'I' configuration position (see photograph on the right).These are ideal for use within steel stockholders. Once offered up to the horizontal flange of the girder they are locked in place by the jaw locking lever.The design allows the clamp to be used individually, however for longer girders they should be used in pairs in conjunction with a spreader beam

The TSZ 'two way' screw clamps have all the same features of the TSD (shown above) but have the additional benefit of a second lifting point enabling it to pull in two different directions.NB. The plate surface of the material to be lifted must not exceed a hardness level of HRC 30Brinell 300.

Working load limit (WLL) 1000 - 30000kgsThese clamps are primarily used for transporting sheet metal and steel plates in the vertical position, as well as lifting and rotating through 180'. They can also be used for transporting steel constructions and profiles. It is recommended to use a pair of plate clamps in conjunction with a spreader beam for long materials which have a tendency to sag or flex. Function The jaw is opened and closed with the locking lever. The safety lock spring loads the cam jaw, preventing the clamp from opening even when there is no load. Workmanship and parts These plate clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person. NB: The plate surface of the material must have a hardness level below HRC 30Brinell 300.

The CY plate clamps with hinged hook rings can be used for the safe handling of plate at various angles. It can lift plate from the horizontal and put down in the vertical. The hinged hook ring ensures adequate gripping pressure in every position, but the load capacity is reduced as seen in the diagram below showing the load force capacities. The main benefit of the CY hinged plate clamps is that longer plates can be lifted or handled, using two clamps on a two legged chain sling (as shown in illustration), thus eliminating the need for a spreader beam. NB: The plate surface of the material must have a hardness level below HRC 30Brinell 300.

Standard plate clamps with safety lock working load limit (WLL) 500 - 3000kgs These clamps are primarily used for transporting sheet metal and steel plates in the vertical position, as well as lifting and rotating through 1800. They can also be used for transporting steel constructions and profiles. It is recommended to use a pair of plate clamps in conjunction with a spreader beam for long materials which have a tendency to sag or flex. Function The jaw is opened and closed with the locking lever except for the 92-500 which uses a positive spring-loaded cam. The safety lock spring loads the cam jaw, preventing the clamp from opening even when there is no load.

The TSB non-marking plate clamps with chain are designed for vertical lifting and transporting of plate material. This particular range of clamps has a large jaw capacity that enables it to be used on a multitude of applications.The main feature of the TSB plate clamps is the fact that it is non-marking. It works through the process of 'friction'. This is achieved by a special material on the jaw and pad which is similar to brake linings.Other benefits of the TSB, is that one grab can also be used for lifting materials such as concrete, wood, stone, and hardened steel.

The TAG universal clamps are extremely versatile. They have a large jaw capacity that enables them to be used on a multitude of applications such as loading machine tools, steel constructions, welding and numerous assembly duties. The design means that they do not require additional chain slings and are very easy and simple to use. The automatic gripping force is retained by a positive tension jaw spring, even if there is slack in the chain. The clamps are also fitted with a 'Quick-Open' lever for ease of loading and unloading. These clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person. Protective lined jaws can be fitted up to 1250kgs WLL.

The main purpose of the CG girder turning clamps is for the transportation and turning of steel girders (RSJ) through 900 degrees.They can be used individually or for longer beams used in pairs in conjunction with a spreader beam as shown in diagram.The clamps are attached to the horizontal flange of the girder and locked in place by the jaw locking lever. Once lifted the girder will turn through 900 degrees.

Designed for hardened material. Working load limit (WLL) 500 - 4000kgs HG plate clamps have an extremely high clamping force which makes the clamps particulars suited to the transport of plate with a surface hardness up to HRC 40Brinell 375. Function These clamps are opened and closed with a locking lever. The safety lock spring loads the cam jaw, preventing the clamp from opening even when there is no load. Workmanship and parts These plate clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person.

The LJ non-marking plate clamps are designed for lifting, turning and transporting of all structural steel plates, stainless steel, iron, timber and aluminium without marking, damaging or leaving indentations on the surface. It can also be used for plates with extremely hard surfaces.As standard these clamps come with leather lined pads and jaws, however there is also the option of having rubber or plastic pads fitted for use with polished materials. Contact our sales team for details.These plate clamps are service-friendly, making it easy to exchange parts, which are readily available. Clamp repairs are available through the factory, or can be done by a competent person. NB: The surface of the plate must be free of oil, grease or any other liquid to ensure safe transport.

The SCB bulb bar clamp is a variant of Camlok's SCA clamp and is particularly useful in the ship building industry. The clamp has a large bow shackle for quick and easy attachment of hoist slings etc. Also available with load bar for low headroom.

The TSH 'swivel hook' screw clamps offer many possible applications. It is particularly useful for lifting, transferring and pulling sheet metal, girders and steel constructions.The clamps are supplied complete with an alloy safety shackle, that allows for pulling in 180' degrees.NB. The plate surface of the material to be lifted must not exceed a hardness level of HRC 30Brinell 300.

The THK horizontal plate clamps share the same basic design features as the CH range of clamps but have a reversed tooth jaw design. This acts as an additional safety feature specifically for use with thin sheets which may have a tendency to deflect or sag or flex.The THK clamps are particularly suited to thin plate with a surface hardness less than 300 Brinell 32 Rockwell C.

TPZ board clamps offer an simple and effective way to vertically lift and transport a variety of materials such as wood, MDF, plasterboard, stone, and plastics. They can also be used to lift loads from the horizontal to the vertical through 900 for transportation. The range has been designed to be user friendly and the handle enables the operator to guide the load easily during operation and each clamp is supplied fitted with large rubber pads to minimise damage.These clamps are ideal in production facilities and especially on construction and building sites.

Working load limit (WLL) 1500 - 3000kgs*The BTG concrete pipe lifting clamps are sold in sets of three and they come complete with chain slings (the working load limits shown are based on a set of three clamps).They are designed for the vertical transportation of concrete pipe sections with a diameter of up to 2000mm.The jaw capacity is designed for pipe thickness of 40 - 200mm.Attachment and removal of the clamps from the pipes is extremely easy due to the simple and straightforward design.

The SCA screwlok beam clamps offer many of the same features as our other beam clamps however this range is specifically designed to be attached to rolled steel angle. These are normally found against the wall of a roof.

The HGC hand grip clamps are suited for the individual transport of light and thin plates. They have a jaw capacity of up to 10 mm and can lift up to 250kgs.To operate the clamp you simply press down on the hand grip which compresses a spring. This allows the clamp to open and slide onto the plate. The plate can then be lifted and transported using the ergonomically designed hand grip. The positive spring pressure prevents the plate from accidentally slipping out of the clamp.NB. Plate surface of material lifted must not exceed a hardness level of HRC 30Brinell 300.

Camlok have now designed a brand new range of reinforced beam clamps. The YRC clamps have all the standard features associated with the SC range of clamps but have the added benefit of being extremely tough and robust, due to the reinforced side plates and jaws.This design change makes them a very safe attachment point, even under demanding conditions.

The SCS screwlok beam clamps have been specifically designed for use as a semi-permanent anchor point.This range is fitted with swivel jaws that a give a more positive grip to the beam flange.These clamps are fitted with a shackle suspension point and are very quick and easy to attach to the beam by simply turning the threaded middle bar.

The THS horizontal plate clamps are specifically designed to be used whenloading plate horizontally into presses, shears, guillotines and other industrial machines or where the CH clamps are not suitable.The unique design of the THS allows them to be used individually when loadingplate. However, when transporting plate horizontally the THS clamps should be used in pairs.Other features of this clamp include a spring loaded safety lock that ensures the clamp remains on the plate in the unloaded position prior to lifting.Maximum plate surface hardness 300 Brinell 32 Rockwell C.

The SC92 beam clamp provides a quick and versatile rigging point for hoisting equipment, pulley blocks or loads. The unit offers flexible applications, due to the wide adjustment range. The central threaded spindle allows easy attachment and a safe and secure grip to the beam flange.NB. THIS MODEL MUST NOT BE USED FOR LIFTING.

The SC beam clamp provides a quick and versatile rigging point for hoisting equipment, pulley blocks or loads and comes complete with a locking device.The unit offers flexible applications, due to the wide adjustment range. The central threaded spindle allows easy attachment and a safe and secure grip to the beam flange.NB. THIS MODEL MUST NOT BE USED FOR LIFTING.

The ACH horizontal plate clamps offer superb flexibility because of the large adjustable jaw opening. The jaw is adjusted using a simple ratchet mechanism.These clamps are to be used in pairs and are especially suited to the transportation of large plate bundles

Heavy duty - side loading The CX plate clamps shares all the benefits of the CY clamps, but are specifically designed for more heavy duty applications. The other benefit that the CX clamps offers over the CY clamps is that vertically racked plates can be turned through 90 (as shown in illustration) NB: The plate surface of the material must have a hardness level below HRC 30Brinell 300.

The TSD standard screw clamps offer many possible uses. They are designed to be used in conjunction with ratchet lever hoists to align steel structures or fabrications. They are ideally suited for the construction industry. The unique design of the spindle makes it easy to attach to 'angle' plate. This is achieved by simply turning the handle which applies the pressure to the plate holding it securely. NB. The plate surface of the material to be lifted must not exceed a hardness level of HRC 30Brinell 300