Capacity: 500 kg L.C. 20g
To determine the Single / double yarn strength of any type of Yarn. Elongation can also be measured on display panel. Maximum capacity 500Kg with 20gms accuracy, works on CRE principle.
Digital control panel with digital extension meter. Maximum jaw separation 450mm & minimum jaw separation 25mm. The controller is microprocessor based and has the facility of over load protection, peak hold and auto calibration. The load directly indicated in kilograms or Newton. Complete with all accessories including jaws.

Micro-controller based electronic twist tester to determine Twists in double or multiple plied yarns only. Suitable for S/Z type of twisted yarns.Yarn Test Length: 250 mm OR 10 Fixed Length.Suitable for S/Z type of twisted yarns, multi as well as single filament yarns.Electronic sensor for sensing zero (starting) position Tension weight up to 100 Grams adjustable in step of 5 Grams.
Elongation Rang: +40 mm. With tolerance of 5 mm for movement in other direction.Accurate twist measurement of single, plied and OE yarn specimens.

To determines the property of textiles to recover from creases by measurement of the recovery angle.

Digital shore hardness tester is mainly used to measure the hardness of vulcanized rubber and plastic products; there are A, C, D three types. Type A and D are respectively suitable to measure the hardness of low, medium hardness and high hardness rubber. Type C is suitable to measure the hardness of cellular rubber and plastic material usually with the compression ratio 50%, the pressure more than 0.049MPa. The product confirms to the standards of GB/T531, GB2411, HG/T2489, and JB6148.

Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials With test Piece.
Dual Needle helps to take the reading after removing from the work piece. Technical Details :

IRHD hardness testers (IRHD = International Rubber Hardness Degree) determine the indentation depth of materials, from foams to rigid plastics and rubber.
A measure of the indentation resistance of elastomeric or rubber materials based on the depth of penetration of a ball indentor.
An initial contact force is applied to an indentor and the penetration is set to zero. The force is increased to a specified total load and the depth of penetration is measured. The IRHD value is related to the depth of indentor penetration.

IRHD Hardness Standards :ASTM D1415, DIN 53519 Sheet 2, ISO 48.

Capacity :0 35 Kg / sq.cm.
To determine the Bursting strength of any material such as fabric, leather etc. is its strength under multi directional force and is defined, as the hydrostatic pressure required producing rapture of the material when pressure is applied at a controlled increasing rate through a rubber diaphragm.

Analogue Opening in upper clamp : 30.5 mm diameter and Opening in lower .
Clamp : 38.1 mm diameter. Rate of fluid displacement: 95 cc/minute Pressure.

Standards :ISO 2758 / 2559 / 3303 / 3689, ASTM D3786, BS 3137 / 3424, IS 1966.

Micro controller based electro-mechanical testing machines suitable for carrying out tensile test on variety of materials such as yarns, fabrics, Lea, Elastomers, papers, wires, etc.Various models are available up to 500 Kg. force rating. These table top machines consists of lower stationery base plate, a fixed cross tie on two supporting columns and a movable crosshead using a lead screw and nut mechanism. The crosshead is extended on both sides to have 2 testing spaces for accommodating 2 different load sensors with different set of grips. The machine has been designed in such way that one testing space is suitable for extra long test sample, having long elongation.The facility of controlling the test via Computer with online force v/s elongation graph is also available with data analysis & report printout facility, tension, compression, cyclic & stress relaxation test can be carried very effectively using extremely powerful interactive software, which makes the machine versatile.FEATURES :Micro Controller based Panel-incorporating State of Art Technology.Digital Display of Force, Elongation & Speed values on large Backlit LCD Display Unit.Choice of multiple load cells selectable via keyboard.Peak Force Memory Facility.Choice of Fixed or Variable Testing Speed.Closed loop servo system in variable speed Model.Speed selection via keyboard.Displacement measurement using Optical Encoder.Safety interlocks for overload and over travel.Communication port for downloading test data in computer.Software for computer control of machine with online graphic display & test report.Choice of Grips & Fixtures for variety of materials.Compact & Elegant design.

Standards :ASTM-D 5035, ASTM-D 1578, ASTM D-5034, ASTM D-434, BSEN 1002-3, BS-1610, DIN-51221APPLICATIONS :Yarn & Fabric Strength Testing.Lea Strength Testing.Paper Peel off Strength Test.Wire Tensile Strength Testing.Tensile Testing of Elastomers, Rubbers, Corks, PVC, Teflon, Leather and Metal Strips.
Cyclic Testing.Stress Relaxation Test.