Kushveer Pharma Machineries

Ring Road, Rajkot, Gujarat

GMPFluid Bed Dryerwith latest improved design makes this unit a truly versatile for Pharmaceutical, Food, Dyestuff & Chemical industries. OurFluid Bed Dryeris capable of drying materials in any forms like granular, powder or crystalline. Afluidized bed of solid particles with a stream of air passing up-ward through the particles at a rate great enough to set them in motion. As the air travels through the particle bed, the particles behave as boiled water. The active motion creates the potential for improved mixing and results an isothermal property. In a bubbling fluidized bed, no temperature gradient exists within the mass of the fluidized particles. Because the temperature and volume of the air can be precisely adjusted, the process achieves fast heat transfer making it very efficient, yet gentle on the product. Our product precisely maintains moisture content up to 20% which is ideal for pharmaceuticals and chemicals .

Fluid Bed DryerThe capacity ranging from 10 / 30 / 60 / 120 / 150 / 200 / 250 / 300 / 500 Kgs., with steam heating / electrical heating & thermal heating facility.Electrically / Steam & Thermic Fluid Heated in which general structure, made out of mild steel & painted in Standard Model & made out of S.S.304 quality material & polished to the matt finished in GMP Model, but contact parts i.e. Product Container and Retarding Chamber, are made out of S.S.304 / S.S. 316 quality material, with Non-Flameproof blower motor, (Flameproof motor provided on demand) suitable to dry wet material.Three Piece GMP ModeOperationFLUID BED DRYER is designed to introduce the hot air stream at the base of the product container which is filled with the material. Induced draught is created by means of blower and fresh air is sucked in to the unit. The fresh air is heat by means of electrical heaters or steam or thermic fluid heaters. This hot air stream expands the bed of material at certain velocity & creating turbulance in the product. The phenomenon is known as fluidisation and offer conditions which are almost ideal for drying. Fluidisation produces full agitation of solid particles and since each particle gets surrounded by hot air, heat transfer is extremely high and uniform. The product is dried fast without appreciable loss of heat. Filter bags prevent particles escaping from the dryer.SuitabilityThe conventional drying method of drying products in tray dryer is rather inadequate and trouble some. They occupy large floor space, have very high drying times, are labour intensive and offer uneven drying. On contrast Fluid Bed Dryer occupy comparatively lesser floor space, are very easy to operate & can dry material in least time as compared to tray dryer.In Fluid Bed Dryer, temperature distribution through out the product is uniform and the heat transfer rate is very high. Due to the reduce drying time high production rates are achieved.As the product is in close contact with drying air at low temperature and also for short duration, the physical and chemical properties of the products are generally not effected and therefore the dryer can effectively be used for heat sensitive products. Due to the continuous movements of product during drying lump formation, case hardening etc. are minimized.The Fluid Bed Dryer are most suitable for drying granular, crystalline, coarse or similar material in pharmaceuticals, fine chemicals, dyes, food and allied products. The Fluid Bed Dryer is not suitable for drying liquids or pasty materials.Special FeaturesUniformity in drying and reduction in drying time.Atmospheric inlet air is filtered by means of non woowen filter cloth. PRE /MICRO V & HEPA filters can be provided on demand on extra cost to prevent any fine dust to pass through the products.Digital temperature indicator cum controller for inlet air & Digital temperature indicator for outlet air, are provided for electrically heated model.Digital temperature indicator are provided for inlet & outlet air, in steam / thermic fluid heated model. (Temperature controlling valves will be in customer scope of supply)Manually operated air dampers provided to control the inlet and outlet air flow.An explosion safety flap of adequate capacity at the rear of dryer and an earthing point to prevent static charge in the machine.Contact parts RETARDING CHAMBER & PRODUCT CONTAINER are made out of SS304 & polished to the mirror finished and other parts are made out of SS 304 and polished to the matt finished in Gmp model & made out of M.S. & Painted in standard model.

We are offering tray dryer. the dryers are made of trays held in a cabinet which is connected to a source of air heated by gas, diesel or electric. The air temperature is usually controlled by a thermostat which is normally set between 50 and 550c. The air enters the bottom of the chamber below the trays and then rises, through the trays of food being dried, and exits from an opening in the top of the chamber. In the practical action systems the trays are designed to force the air to follow a longer zigzag route which increases the air / food contact time and thus improve its efficiency. operating principle of tray dryer jas enterprises offer tray dryers having capacities ranging from 12 to 200 trays and temperature ranging up to 550 celsius (932 fahrenheit) . These trays are available in the different size. A fan impeller with an axils flow design is provide for better uniformity and quick drying. Is equipped with a digital temperature indicator controller for accurate temperature control. Control action on off or pid or as required control accuracy. The material used for construction of dryer of mild steel/ aluminum/ ss 304/ ss 316 or frp-lined or as per requirements. The company offers these try dryers in flameproof and spark proof version. Heating can do through electrical /thermo fluid or steam radiator / oil fired hot air generator.