Paints #158747

chlorinated rubber is a premium quality, single pack, unmodified chlorinated rubber finish. it is resistant to salt spray, all types of acids, impermeable to water and exhibits excellent resistance to mould and fungus growth. chlorinated rubber can be applied over correctly prepared and primed steel and concrete surfaces.

primary uses

• fishing bins

preparation of substrate

• surfaces showing heavy scale or surface rust should be treated with protec metal conditioner and degreaser.

• heavily rusted surfaces should be abrasively blast cleaned.

cleaning : before and after any sanding operation, the substrate must be thoroughly degreased with & grease remover to remove all traces of dirt, oil, grease, silicone, wax etc.

drying times will vary dependent on temperature, flash off between coats, number of coats used.

• is suitable for brush application on small areas.

• 37% volume solids (depending on colour).

When used as part of approved scheme, this material has following certifications

• Food Contact - Carriage of Grains ( NOHA )

• Food Contact - FDA Compliant : Dry Foodstuffs

• Tested for non-contaminations of grain cargo at the

Theoretical spreading rates :

• 3.9 m²/litre - 200 micron 3.9 m²/litre - 200 micron

• 154 sq.ft./US gallon - 8 mils 154 sq.ft./US gallon - 8 mils

Introduction to Food Grade Epoxy

• A low viscosity, 100% volume solids epoxy coating

• Compliant with SSPC paint 42 specification

• Applicable over variety of substrates including Aluminum, Concrete, Glass, FRP, GRP etc.

• Flexibility in application – can be applied directly over tightly adherent rust, old coating, oily, condensed & splash zone surface. Can be used underwater for wrapping of piling, jacket legs & variety of substrates

Properties of Food Grade Epoxy

• 100% Solid Epoxy Coating

• '0' Volatile Organic Compound

• Food-grade certified

• '0' Flame spread

• Applicable directly on difficult surfaces, viz. Stainless Steel, Aluminum, Galvanized Iron etc.

Examples of Applications

• As a protective coating for structures in harsh environment

• Condensation structure / piping

• Online high heat application (≤ 150°C)

• Underwater piling, jacket legs, risers

• GRE/GRP piping

• FRP strengthening

• As a Metal Filling Compound (MFC) (≤5mm)

• Oily bilge wells / pump rooms / engine room

• Concrete & concrete repairs

• As a floor-coating – also for "Clean Room" applications

"Happy to inform you that we stock and trade in this Food Grade Epoxy Paints, we have observed visually and found satisfactory paint which was applied on condensate surface lines at our premises”

Food Grade Epoxy Paints – an innovative 100% solid multipurpose epoxy coating

• Meets & exceeds the requirements enlisted in SSPC Paint 42 specification

• 100% solid epoxy – no solvents added – “0” VOC

• Specially formulated for multipurpose use in offshore environment

• No stringent requirements for surface preparation – can be applied on tightly adherent rust

• Equally good performance even when applied on oily or damp surfaces

• Applicable directly underwater without any modifications

• Can be used along with wrapping tapes underwater for extra protection to risers, piling, structure etc.

• Along with Zirconium (added externally), can be used as a Metal Filling Compound

• Food grade coating – DNV certified – applicable for internal lining of Potable water tank

• Class “0” rated fire retardant

APPLICATIONS

• Crude, product & potable water storage tank linings

• Ballast tank coating where surface preparation may be an issue

• Bilges, pump rooms etc. where there is a high possibility of oily substrate

• High temperature application (up to 150 deg. C)

• Engine shell coating

• Sweating lines – can be applied directly without shutdown

• Risers, jackets, piling – for underwater application

• GRE & FRP repairs & restoration

• Self-levelling floor coating – Sterile grade

A single component, high temperature coatings, based on moisture curing silicone binder. On offshore facilities there is a continuous demand for coatings that maintain their performance despite exposure to a variety of environmental conditions and various temperature fluctuations from the substrate. The company has developed a range of heat resistant, high performance, high quality coatings meeting the latest requirements of the offshore industry. The coatings can be applied on pipes and steel surfaces as well as on process equipment. The coatings protect the steel from the influences of thermal cycling, which is one of the most extreme challenges faced by coating systems. For the protection of steels from corrosion on areas including flare stacks, chimneys, exhausts, vents, and pipework temperature upto 600©. Some of the most challenging coatings situations that exist in industry today concern heat resistance. There is a continuous demand for coatings that can maintain their function despite exposure to the extremely high operational temperatures found in the power, offshore and petrochemical processing industries. We offers a range of high quality, high performance heat resistant coatings developed specifically to meet this challenge, able to cope with extremes of temperature and deliver a dependable long-term performance for both new construction and maintenance alike.

Product Features :

• A heat resistant moisture curing silicone aluminium Finish meeting all maintenance requirements up wide range of temperature.

• One component

• Aluminium Pigmented

• Heat resistant on SA 2.5 blasted Steel

• Heat resistant on ST3 powertool cleaned steel

• No post-cure required

• Application direct to metal or zinc silicate primer

Applications : The products is widely used and respected in all key industry sectors, meeting the very demanding challenges required to protect major assets. Performance you can trust All our coatings are manufactured to world-leading standards. So you can rely on a consistent performance from each and every coating.

• Petrochemical : Piping, Heat Exchangers, Maintenance, Process equipment

• Power : Piping, Stacks, Process equipment

• Offshore : Piping, Heat Exchanger, Maintenance, Flare Stacks

Aggressive environments demand highly durable systems. Incorporating innovative technology, the Polyurethane Epoxy paints range of atmospheric, durable finishes meets these requirements and offers exceptional cosmetics for all atmospheric vessel and Industrial areas.

Independent approval : Polyurethane Epoxy Paints has been tested to meet, and exceed, the highest international standards, such as ISO 12944, and NORSOK M501.Certified by DNV as a paint system with low-flame spread in compliance with IMO Solas and Marine Equipment Directive (MED).

Features

• Finish coating for decks, superstructure, and topsides

• Suitable for application at new-build, in dry dock and for onboard maintenance

• High gloss with up to 10 years’ durability

• Non-chalking and non-yellowing

• Excellent application properties with minimal overspray

• Resistant to splash of mineral and vegetable oils, paraffins, aliphatic petroleum products and mild chemicals

Benefits

• Excellent application properties by spray application, roller and brush

• Durable for up to 10 years – less maintenance costs

• Flexibility of use – simplifies stock lists

• Easy to apply – less time, more productivity

• Fast drying – reducing maintenance downtime

• Unlimited recoatability

• Outstanding gloss retention – easier cleaning

• Reliable and proven track record

This epoxy paints is a 100 % solvent-free, two component, High-Build, Polyamine adducted cured epoxy paint specially developed for long term protection on concrete and steel potable water tanks. The product is designed for use at both new building and maintenance of existing potable water tanks. The product contains no solvents, benzyl alcohol or nonyl phenol that can influence taste or smell. This means that quality water is mainntained that way. This Products is approved by the Water Research Centre (WRAS), Great Britain, according to BS 6920 for potable water up to 23C/73F. It is also covered by the Norwegian Health Authorities (Folkehelseinstituttet), Norway, for use in tanks for potable water offshore according to system 3A in NORSOK M-501, revision 5.

Product features and benefits

• Certified and approved for portable water use

• 100% Solvent-free and Benzyl alcohol free

• Application friendly

• Long overcoating window

• Light colour for easy inspection

Certificates/Approvals : This products is in accordance with ARAMCO's specification APCS 2A, 2B and 2C. Approved for aviation fuel storage tanks by Exxon Mobil Aviation International Ltd. England. Approved by Water Research Centre, Great Britain, for potable water up to 23C/73F. Approved by Folkehelseinstituttet, Norway, for potable water - cold water. Certified by NSF, USA for use in potable water tanks with volumes of 1000 gallon or greater, valves at 2 inches (5 cm) or greater, pipes at 16 inches (40 cm) or greater. NSF certification applies to US manufactured product only. Conforms to Norsok M-501, system no. 3.