Measuring Instruments & Equipment

We are leaders in the market for providing best range of Energy Management Systems Basic Meter, Energy Management Systems DC Multi Function Meter, Energy Management Systems Maximum Demand Meter, Energy Management Systems Multi Function Meter and PRE SET COUNTERS

Energy Management Systems Basic Meter

Product Features :

EMS-11: Measurement of current parameters (L-N) *CT primary and secondary programmable.
EMS-12: Measurement of voltage parameters *PT primary and secondary programmable.
EMS-13: Measurement of frequency parameter.
EMS-14: Measurement of Power Factor parameter.
EMS-02: Measurement of basic parameters.(Current (L-N), Voltage (L-N), (L-L), frequency (average) and Power factor (Total) * CT ratio programmable, RS485 Mod-bus RTU protocol available, Sensing : True RMS.
EMS-18: VAF Meter with True RMS Sensing.
Program can be locked by removing short link connected across specified terminals.
Hold/Scroll Facility available .

View Complete Details

Ask Latest Price & Details

Energy Management Systems DC Multi Function Meter

Product Features :

Micro Controller based 3 Channel DC Energy Meter.
Displays DC parameters V, I, KW, KWh , MWh & Load on hours of all three channels.
Displays one set old Energy readings and Communication status.
Display Hold / Scroll Facility available.
Programmable Shunt ratios.
Alphanumeric display for Parameter & values.
RS-485 serial port with Modbus RTU output.
Wide Input Voltage and Current Range.
Protection from dust and water as per IP-51.

View Complete Details

Ask Latest Price & Details

Energy Management Systems Maximum Demand Meter

Product Features :

Measurement of basic, power, energy and demand parameters.
On-site programmable PT and CT ratios.
High brightness LED display (alpha numeric for parameter, numeric for value.
Automatic CT reverse correction for energy and demand.
Programmable demand techniques : block / sliding window.
Programmable demand parameters : Apparent / Active power.
Programmable demand range : Kilo / Mega.
Programmable Alarm / hysterisis settings.
Program RTC time to match EB meter's clock.
For EMS-15C : Max. Demand Controller = Max. demand indicator + Relay module (4 relay)(RR-4)
4 control outputs for alarm and trip settings.

View Complete Details

Ask Latest Price & Details

Energy Management Systems Multi Function Meter

Product Features :

Microcontroller based multifunction A/C Energy Meter.
Accuracy Class1.0 / (Class 0.5 calibration on Request).
CT /PT (Pri/Sec) Programmable.
Digital Measurement.
IEC 62052-11 IEC 62053-21 IEC 62053-22 IEC 62053-23.
RS 485 Serial Port with Modbus RTU Output.
Flush / Panel Mounting .
96 x 96 mm DIN Mounting.
Auto Scroll / Hold Facility.
Internal Resettable fuse for protection of device against voltage fluctuations.Digital display will blink whenever voltage exceeds specified voltage range.Switch off the unit for sometime & then switch on when voltage returns to normal.
Protection from dust and water as per IP-51.

View Complete Details

Ask Latest Price & Details

PRE SET COUNTERS

Product Features :

Din sized enclosure for panel mounting.
Wide Voltage range.
Front / Rear reset facility provided.
Hold / Restart options (selectable) during power failure.
Input signal from proximity switch ( NPN / PNP type) or Potential free (zero volt) signal from limit switch, relay o/p etc.
Over-voltage protection
CT-5: Digital, single window 5 digit 7 segment red LED display with up counting for process value.
Preset Counts can be programmed with the help of thumbwheel switch
H3CT-5U : Digital, single window 5 digit 7 segment red LED display with up counting for both process value and set value
Input sensitivity programmable (1-100Hz)
Internal Resettable fuse for protection of device against voltage fluctuations. Digital display will blink whenever voltage exceeds specified voltage range. Switch off the unit for sometime & then switch on when voltage returns to normal.
Source voltage : 85 270V AC/DC