The MicroSD Card Adapter is a Micro SD card reader module, which uses the SPI interface via the file system driver, microcontroller system, to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE  with an SD card to complete the library card initialisation and read-write function. Specifications Micro SDHC card (

This tiny module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s that don’t have their own protection circuit.  Based around the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished. Futhermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time. Using the module Connect micro USB cable for power, or 5V DC to pads marked IN+ and IN- on left-hand side of the module Connect cell to charge to B+/B- pads on right-hand side of module A load (something for the battery to power) can be connected to the OUT+/OUT- pads on the right-hand side Important! Disconnect load when charging The red LED indicates chaging in progress, green LED indicates charging has finished. Never charge your battery at a rate greater than 1C. Specifications Input voltage – 5V via microUSB or solder pads on left-hand side of module Full charge voltage – 4.2V Charging current – 1A by default. However you can change this by changing the 1k2 resistor next to the “IN-” pad the bottom-left of the board.

• ColorGreen
• ApplicationHome Use
• FeatureLong Life, Stable Performance,Long Life
• QualityBest
• ConditionNew
• PerformanceOptimum
• DurabilityLong Life
• MaintenanceLow

These round high capacity cells have been mainly used in flashlight type applications but with its capability to be used as a drop-in rechargable cell at 3.7V with a capacity of 2600mAh. This is a great battery option for those of you who need a simple-to-install and replace cell with a lot of juice.   These 18650 Cells have a standard discharge current of 0.2C to a maximum of 1C and can handle about 300 charge cycles.

• ModelLR1130 (SR54 / AG10 / SG10)
• Cell Type: Button cell 
• Nominal Voltage(V) 1.5
• Nominal Capacity(mAh)* 68
• External Diameter11.6 mm
• External Height3.05 mm
• Operating Temperature Range(deg. C): –20 to +85

These are generally used to power small toys, clocks, LEDs, watches, calculators etc.. High quality & stable 1.5v Alkaline batteries.  

The MicroSD Card Adapter is a Micro SD card reader module, which uses the SPI interface via the file system driver, microcontroller system, to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE  with an SD card to complete the library card initialisation and read-write function. Specifications Micro SDHC card (

This tiny module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s that don’t have their own protection circuit.  Based around the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished. Futhermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time. Using the module Connect micro USB cable for power, or 5V DC to pads marked IN+ and IN- on left-hand side of the module Connect cell to charge to B+/B- pads on right-hand side of module A load (something for the battery to power) can be connected to the OUT+/OUT- pads on the right-hand side Important! Disconnect load when charging The red LED indicates chaging in progress, green LED indicates charging has finished. Never charge your battery at a rate greater than 1C. Specifications Input voltage – 5V via microUSB or solder pads on left-hand side of module Full charge voltage – 4.2V Charging current – 1A by default. However you can change this by changing the 1k2 resistor next to the “IN-” pad the bottom-left of the board.

• ColorGreen
• ApplicationHome Use
• FeatureLong Life, Stable Performance,Long Life
• QualityBest
• ConditionNew
• PerformanceOptimum
• DurabilityLong Life
• MaintenanceLow

These round high capacity cells have been mainly used in flashlight type applications but with its capability to be used as a drop-in rechargable cell at 3.7V with a capacity of 2600mAh. This is a great battery option for those of you who need a simple-to-install and replace cell with a lot of juice.   These 18650 Cells have a standard discharge current of 0.2C to a maximum of 1C and can handle about 300 charge cycles.

• ModelLR1130 (SR54 / AG10 / SG10)
• Cell Type: Button cell 
• Nominal Voltage(V) 1.5
• Nominal Capacity(mAh)* 68
• External Diameter11.6 mm
• External Height3.05 mm
• Operating Temperature Range(deg. C): –20 to +85

These are generally used to power small toys, clocks, LEDs, watches, calculators etc.. High quality & stable 1.5v Alkaline batteries.