An uninterruptible power supply, also uninterruptible power source, UPS or battery/flywheel backup, is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails.A UPS differs from an auxiliary or emergency power system or standby generator in that it will provide instantaneous or near-instantaneous protection from input power interruptions by means of one or more attached batteries and associated electronic circuitry for low power users, and or by means of diesel generators and flywheels for high power users.  Offline / Standby:- Offline / standby UPS. Typical protection time: 0–20 minutes. Capacity expansion: Usually not available The offline / standby UPS (SPS) offers only the most basic features, providing surge protection and battery backup. The protected equipment is normally connected directly to incoming utility power. When the incoming voltage falls below a predetermined level the SPS turns on its internal DC-AC inverter circuitry, which is powered from an internal storage battery. The SPS then mechanically switches the connected equipment on to its DC-AC inverter output. The switchover time can be as long as 25 milliseconds depending on the amount of time it takes the standby UPS to detect the lost utility voltage. The UPS will be designed to power certain equipment, such as a personal computer, without any objectionable dip or brownout to that device. 

• RatingUpto 5 MVA, upto 33 kV on primary side
• StandardsIS:2026

SERVO VOLTAGE STABLIZERS  ........................................................................ Voltage fluctuation  is a common phenomenon in every part of the country. Automatic Voltage Controller (Stabilizer) is an equipment to obtain constant voltage tram flucfuating supply system. The industrial units running round the clock usually face the problem of low & high voltage. 90% of industrial load is of motors. Electric motors draw considerably high current at low & high voltage. This higher current affects the electric motors (particularly smaller capacity motors upto 7.5 H.P.) in these ways: . Higher current produce higher losses in Electric motors which cause premature failure of winding.  Higher current produce higher losses in Electric motors which cause premature failure of winding.  These higher current of Electric motors also increase losses of Cables, Switches, Transformer & other associated equipments.  This higher current of Electric motors require 15-20% higher setting of over load relay to avoid frequent tripping of motor's starter. Higher set­ting of over load relays have very little safety margin against single phasing and over loading conditions.  the installation of the stabilizer and maintaining 390/400 volts, the motor will operate smoothly drawing 15-20% lesser current and corresponding the relay setting can be reduced by 15-20%. In case single phasing occurs, the relay will trip in 40-50 seconds. The motor can withstand the high current for this period and will be safe. Also, the relays, contactors, switchgears , etc. incorporated with the motor will be safe.

CT & PT UNITS ........................................................................ Current Transformers (CT) and Potential Transformers (PT)  are used to lower the magnitude of the current and voltage to be measured. Say 100Amp current is flowing in a circuit and you want to measure it. If you connect an ammeter to measure the current the ammeter has to be built to handle that current. Or say if you want to measure current and voltage in a high voltage circuit at 220kV, you need properly insulated meters to withstand that voltage. The meters will be very big for that purpose. The CT and PT is used to solve this problem. The CT and PT works on the principle of transformer and lowers the current and/or voltage at a lower value which can be safely and easily measured. For energy measurement connect the CT and PT secondary to the terminal of the energymeter. However you need to select the proper CT and PT and if you are measuring 3phase power you need to connect the CT and PT as per the requirement.  OR 33KV Outdoor CT-PT Unit Our range of these 33KV outdoor CT-PT units are manufactured and tested to match the international quality. This unit has gained the trust of all our clients and the same is offered in the highest quality standard. This reliable range is offered at a competitive price and has its demand all over the country.

We manufacture diverse range of control panels that are designed using latest technology to suit the varied needs of the clients. These panels also are used in diverse commercial applications and offers accurate longer and reliable operations. We offer highly customized & effective capacitor control panels. Our capacitor control panel are widely used in various industrial unit. Our panel came with a power circuit consisting of contractor, MCB and fuses.  We offer a wide range of motor control panels. These are widely used to feed the larger loads and is available with power stabs. The main task of motor panel is to support high capacity industrial motors. Customization is our forte and all our products are offered as per the specific requirement of our client. We offer a wide range of power control centers to our clients. These are used in various sectors like industrial, commercial, heavy industries . Some of the features of our products are: Weather proof Integrated main switch fuse unit Contractors (Magnetic) Control circuit transformer High temperature controllers Voltmeter.

MARSHALLING KIOSKS ........................................................................ For Power Transformer up to 400 MVA Type tested for IP-55 at ERDA With Oil Temperature & Winding Temperature Indicators Fans & forced cooling pump starters, and automatic supply changeover facility Used for the marshalling of field cables. There are two sets of cables coming to the Kiosks, one originating from the field, while the other going to the control room Kiosks facilitates the criss-crossing and interconnection of both the set of cables

We manufacture diverse range of control panels that are designed using latest technology to suit the varied needs of the clients. These panels also are used in diverse commercial applications and offers accurate longer and reliable operations. We offer highly customized & effective capacitor control panels. Our capacitor control panel are widely used in various industrial unit. Our panel came with a power circuit consisting of contractor, MCB and fuses.  We offer a wide range of motor control panels. These are widely used to feed the larger loads and is available with power stabs. The main task of motor panel is to support high capacity industrial motors. Customization is our forte and all our products are offered as per the specific requirement of our client. We offer a wide range of power control centers to our clients. These are used in various sectors like industrial, commercial, heavy industries . Some of the features of our products are: Weather proof Integrated main switch fuse unit Contractors (Magnetic) Control circuit transformer High temperature controllers Voltmeter.

DC Distribution Board  We are engaged in offering distribution boards, which are extensively used for domestic and industry purposes. Our range of distribution boards are manufactured using galvanized and electro- galvanized material. These are also helpful in preventing the electrical distribution system from various damages, which can be caused due to shot circuit, earth leakage and over load. Some of the salient features of our product: Easy to install and operate Short mounting times Ample wiring space

The online UPS is ideal for environments where electrical isolation is necessary or for equipment that is very sensitive to power fluctuations. Although once previously reserved for very large installations of 10 kW or more, advances in technology have now permitted it to be available as a common consumer device, supplying 500 watts or less. The initial cost of the online UPS may be slightly higher, but its total cost of ownership is generally lower due to longer battery life. The online UPS may be necessary when the power environment is "noisy", when utility power sags, outages and other anomalies are frequent, when protection of sensitive IT equipment loads is required, or when operation from an extended-run backup generator is necessary. The basic technology of the online UPS is the same as in a standby or line-interactive UPS. However it typically costs much more, due to it having a much greater current AC-to-DC battery-charger/rectifier, and with the rectifier and inverter designed to run continuously with improved cooling systems. It is called a double-conversion UPS due to the rectifier directly driving the inverter, even when powered from normal AC current.  

We exports and manufactures of control and rely panels.our panels deliver outstanding performance in terms of durability, simplicity and energy efficiency control and rely panels are Offered at cost effective prices, its also made as per given requirement of our clients.  We offer our clients with a technologically advanced range of relay and control panels. These are used to operate in case of failure of mains. We manufacture our range using superior quality of raw material and components that ensures notable features like durability and accuracy. These are used for protecting and controlling power distribution process and are applicable in host of industries in the power generating process.

An uninterruptible power supply, also uninterruptible power source, UPS or battery/flywheel backup, is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails.A UPS differs from an auxiliary or emergency power system or standby generator in that it will provide instantaneous or near-instantaneous protection from input power interruptions by means of one or more attached batteries and associated electronic circuitry for low power users, and or by means of diesel generators and flywheels for high power users.  Offline / Standby:- Offline / standby UPS. Typical protection time: 0–20 minutes. Capacity expansion: Usually not available The offline / standby UPS (SPS) offers only the most basic features, providing surge protection and battery backup. The protected equipment is normally connected directly to incoming utility power. When the incoming voltage falls below a predetermined level the SPS turns on its internal DC-AC inverter circuitry, which is powered from an internal storage battery. The SPS then mechanically switches the connected equipment on to its DC-AC inverter output. The switchover time can be as long as 25 milliseconds depending on the amount of time it takes the standby UPS to detect the lost utility voltage. The UPS will be designed to power certain equipment, such as a personal computer, without any objectionable dip or brownout to that device. 

MARSHALLING KIOSKS ........................................................................ For Power Transformer up to 400 MVA Type tested for IP-55 at ERDA With Oil Temperature & Winding Temperature Indicators Fans & forced cooling pump starters, and automatic supply changeover facility Used for the marshalling of field cables. There are two sets of cables coming to the Kiosks, one originating from the field, while the other going to the control room Kiosks facilitates the criss-crossing and interconnection of both the set of cables