Other Products / Services #212894

Complete made of stainless steel 304 qlty. crusher is fitted with in built water collection tank fitted with float valve to regulate water supply to machine. Complete with automatic voltage stabilizer on 220/230V AC 50 Hz.

Outer body and inside chamber & trays are made of stainless steel 304 qlty. It has microprocessed digital temp. controller to control temperature at 4 Deg , C 1 Deg, C will have alarm if door is opened, temperature deviations to low or high. It may be supplied with pull out drawers. It has hermetic compressor with non CFC refrigerant with chart recorder and voltage stabilizer automatic to works on 2.20 V 50 Hz.

A constant temperature as well as uniform shaking bath for a wide varieties of applications not involving memo metric measurement such as incubation of Tissue slides and homogenates, protein coagulation, aerobic and anaerobic studies of Tissue Slices and homogenates it atmosphere of various gases or mixture of gases. The bath is double walled inside made of Stainless Steel and outside Mild Steel Sheet and painted in Epoxy Powder Coating. The bath has an oscillating tray riding on ball rollers and oscillated by a Governor controlled variable speed motor, shaking speed range is 40 to 140 cycles per minute.

The temperature is controlled by Hydraulic type Thermostat from few C above ambient to 70 C with maximum temperature 100 C. sensitivity plus minus 0.5 C. A "L" shape thermometer mounted on front panel is calibrated from 0 C to 110 C. in one degree division.

Unitized controlled panel has individual switches for heater's knob reference dial for repeat thermostat setting, control of shaking speed and two pilot lights which indicate heater cycle as well as mains, with 1000 watts immersion element. The bath is complete with one shaking tray, one large gabble cover made of Stainless Steel for overall bath, connecting cord plug for operation on 220/230 volts but without racks and glassware.

A constant temperature as well as uniform shaking bath for a wide varieties of applications not involving memometric measurement such as incubation of Tissue slides and homogenates , protein coagulation, aerobic and anaerobic studies of Tissue Slices and homogenates it atmosphere of various gases or mixture of gases. The bath is double walled inside made of Stainless Steel and outside Mild Steel Sheet and painted in Epoxy Powder Coating. The bath has an oscillating tray riding on ball rollers and oscillated by a Governor controlled variable speed motor, shaking speed range is 40 to 140 cycles per minute.

The temperature is controlled by Electronic Digital Temperature Controller cum Indicator from few degree above ambient to 70 C with maximum temperature 100 C. sensitivity plus minus 0.5 C.

Unitized controlled panel has individual switches for heater's knob reference dial for repeat thermostat setting, control of shaking speed and two pilot lights which indicate heater cycle as well as mains, with 1000 watts immersion element. The bath is complete with one shaking tray, one large gabble cover made of Stainless Steel for overall bath, connecting cord plug for operation on 220/230 volts but without racks and glassware.

Shaking rack & its Capacity to accommodate as above.

Option:Microprocessed PID controller having 4 ramp & 4 soak profile having set mode, alarm parameter, configuration parameter, profile parameter, set point profile, Pv error indicator, parameter for locking etc.

Alarm:It is possible to provide electronic alarm, if temperature deviates more than 5 C to cost extra.

The Bath is double walled inner working chamber is made of Stainless Steel & outer case is made of Mild steel finished in epoxy powder coating paint. Space of 50mm between inner & outer wall of the bath is insulated with puff. The lid of the Bath is insulated double walled fixed with hinges and has locking arrangement. The bath is mounted on castors.

Two sealed compressor, fan cooled condenser & all its accessories are placed at the lower portion exactly below the bath.

Temperature is controlled by Microprocessed Electronic Digital Controller Cum Indicator form 5 C to ambient temperature with accuracy of + - 0.2 C .

Control panel is given on right hand side of the bath having the Rotary switch to operate the bath. ON OFF Switch, Voltmeter, 2 Nos. indicators with Heavy Duty Circulating Pump Motor to circulate chilled water to your external machine to work on 220/230 volts A.C.

Large Dimensions Chiller can be manufactured as per customer's requirement and rates shall be given on request.

Suitable for a wide range of applications such as oxidation stability testes an oils The bath is constructed double walled inside made of Stainless Steel outside of mild Steel painted in epoxy Powder Coating & insulated with 50mm Mineral Wool on five sides.

The temp. is controlled by Microprocessed PID controller cum Indicator from 50 C to 250 C with an accuracy of +/- 0.1C . Control panel is provided on the side of oil bath consisting two neon lights. The bath is complete with High Speed Stirrer and speed regulator, perforated and removable diffuser shelves, with wire and plug, but without thermometers. One rack to hold 6 nos sample . it will have glass window from front and and at back there is also glass window with illumination at back side vertically. to work on 220V 50Hz SHALL BE SUPPLIED WITHVariation range of Bath Temperature : +/- 0.1 C maxPower supply: 230 V, 50 Hz.

Uses:

• Seed Testing
• Biological Studies
• Veterinery Science
• Forestry Research
• Pathology

Construction:

This is double walled cabinet insulated with 75 mm by puff. between interior and exterior walls. Outer chamber made of mild steel and furnished in durable white enamel paint. The inner chamber made of anodized aluminium with shelf supports allowing wide range of shelf positions and spacing.

Diamension of Each Working ChamberHeight 910mm x Width 555mm x Depth 605mm

Each chamber has 14 trays. Totally 28 multi perforated aluminium trays of size 430x480MM each all having 57500 SQ-CM-approx. of testing area. The distance between the tray is 4 CM. Both chamber have full view acrylic door which allows inspections of sample without disturbing temp. of working chamber. Outer double walled metel door with lock and key. A push type switch for illumination lamp is provided in each chamber of inspection of the samples during high condensation cabinet is mounted on caster.

Water Reservoir For Humidity:-Each chamber has stainless steel water reservoir at the bottom and water is heated by low wattage immersion heater which assures to maintain. The humidity from 90 to 95% +/- 3% ( non- adjustable) and to be maintained at this level. Humidity shall be controlled by Micro processed temp. & RH controller temp. accuracy 1 C & RH Accuracy 5 C . Each water reservoir has constant water level arrangement with two no. brass nozzle, one for inlet and other for outlet and a brass drain plug is also provided.

Temperature:- Temp. in both chambers is controlled by a Digital temperature indicator cum controller from in the variation of plus minus 1 deg.c. at any temp. between 5 to 60 deg, c at normal ambient temp. in which chamber is fitted with refrigeration system. In the other chamber, temp. can be maintained from few deg. Above ambient to 50 deg.c. The cooling chamber is provided with a selected switch to operate the unit either above or below ambient temp. desired.

Cooling System:-One chamber has cooling system by a heavy duty sealed compressor with all accessories and also a fan cooled condensor are fitted at the bottom exactly below the working chamber. Copper cooling coil is fitted at the back of inside chamber.

Air Circulating:-Each chamber has separate air circulation by FH Motor with ample provision for an even distribution of air by a fan which assures uniformity of temp. throughout the chamber.

Control Panel:-Control Panel is given at the top of chamber having ON-OFF switch three indicators for main cooling and heating , temp. setting knob which is graduated in the centigrade from 5 to 50 deg.c volt meter in cooling chamber prismatic Digital Temp. Indicator graduated from 0-50 deg.c., to work on 220/230 Volt 50 cycles A.C only.

Optional Arrangements:-

SGA-1 Width 555mm x Depth 605mm x Height 910mm 308 Ltrs.

SGA-2 Specifications as above but provided with heating & cooling in both thechambers from 5 deg.c. To 50 deg.c in bothe chamber instead of one forheating and another one for cooling.

SGA-3 Interior chamber & shelfs made of stainless steelIn both the chambers instead of anodized Aluminium shall cost Extra.

SGA-4 Seed Germinator with two sides lighting arrangement & two nos. 0-24 hourtimer at an extra cost

Alarm:It is possible to provide electronic alarm if, temperature deviates more than 2 C and RH 5% to cost extra.

Uses:

• Seed Testing
• Biological Studies
• Veterinary Science
• Forestry Research
• Pathology

Construction:

This is double walled cabinet insulated with 75 mm by puff between interior and exterior walls. Outer chamber made of mild steel and furnished in durable white enamel paint. The inner chamber made of anodized aluminum with shelf supports allowing wide range of shelf positions and spacing.

Diamension of Each Working ChamberHeight 910mm x width 555mm x Depth 605mm

Chamber has 14 trays.The distance between the tray is 4 CM. chamber have full view acrylic door which allows inspections of sample without disturbing temp. of working chamber. Outer double walled metel door with lock and key. A push type switch for illumination lamp is provided in chamber of inspection of the samples during high condensation cabinet is mounted on caster.

Water Reservoir For Humidity:-Chamber has stainless steel water reservoir at the bottom and water is heated by low wattage immersion heater which assures to maintain. The humidity from 90 to 95% +/- 3% ( non- adjustable) and to be maintained at this level. Humidity shall be controlled by Micro processed temp. & RH controller temp. accuracy 1 C & RH Accuracy 5 C. water reservoir has constant water level arrangement with two no. brass nozzle, one for inlet and other for outlet and a brass drain plug is also provided.

Temperature:-Temp. in chambers is controlled by a Digital Indicator Cum Controller from in the variation of plus minus 1 deg.c. at any temp. between 5 to 60 deg, c at normal ambient temp. The cooling chamber is provided with a selected switch to operate the unit either above or below ambient temp. desired.

Cooling System:-Chamber has cooling system by a heavy duty sealed compressor with all accessories and also a fan cooled condenser are fitted at the bottom exactly below the working chamber. Copper cooling coil is fitted at the back of inside chamber.

Air Circulating:-Chamber has separate air circulation by FH Motor with ample provision for an even distribution of air by a fan which assures uniformity of temp. throughout the chamber.

Control Panel:-Control Panel is given at the top of chamber having ON-OFF switch three indicators for main cooling and heating , temp. setting knob which is graduated in the centigrade from 5 to 50 deg.c volt meter in cooling chamber prismatic Digital Temp. Indicator graduated from 0-50 deg.c., to work on 220/230 Volt 50 cycles A.C only.

SGA-8D Seed Germinator (Without lighting arrangement) inside made of anodized aluminum. Dimension of working chamber H.910x W.555xD.605MM with 14 trays. Fitted with cooling and heating arrangements. Temp. from 5 to 50 deg.c +/- 1 deg.c. Humidity range 90 to 95% plus minus 3%.( non- adjustable)308 Ltrs.

SGA-8LT Seed Germinator SGA-8D provided with lighting arrangement and 0-24 hours time switch for regulating cyclic illumination condition with electronic digital voltmenter in super deluxe model.

Optional:-

Interior chamber and shelf made of stainless steel. 304 Qlty can be supplied, instead of Anodized aluminum.

Alarm:It is possible to provide electronic alarm if, temperature deviates more than 2 C and RH 5% to cost extra.

This is an asset for micro-biological combination testing research, vial filling and bunging operations in parental and for dry processing job in semi conductor industries. Provides a comfortable sit down working position for the operators.

OPTION1. Cock for gas air vacuum line.2. Satin finish S.S. table top in place of mica top

Complete made of Stainless Steel (304 Qlty.) Wtih Acrylic glass door & U.V. Light.

With cock for gas or Vacuum line.

These are designed to provide an atmosphere free from air borne particles with Laminar air flowing downward the work table. An exhaust system may be fitted at bottom and back to throw the air outside the room. The cabinets are mostly used in Medical, Scientific and Industrial applications where very clean environment is required.

1. Satin finish S.S. table top in place of Mica Top at an extra cost:VLF-2 VLF-3 VLF-4 VLF-6

Complete made of Stainless Steel (304 Qlty.) Wtih Acrylic glass door & U.V. Light with cock for gas or vacuum line & exhaust fan.

RATES FOR BIOLOGICAL SAFETY CABINETS OF DIFFERENT CLASS SHALL BE GIVEN ON REQUEST.

This is a premium solution for cytotoxic / antinloplastic drug processing, providing the highest level of patient, pharmacist and environmental protection. The Unique demands of handling and preparing cytotoxic drugs for use in chemotherapy require a specialized cabinet As cytotoxic cannot be inactivated by chemical decontamination, class II biosafetv cabinet should not be used.

Class: III Rio Safety Cabinet

Class - III Biosafety Cabinet is totally and gas tight with ULPA filter and exhaust air work is performed with long sleeved gloves. The cabinet is kept under negative pressure of at least 120 pa and is maintained by dedicated exterior exhaust system. It protects the operator, product and environment.

Made of heavy duty Mild Steel pipe and powder coated each shelf size 1200 x 400mm and distance between each shelf is 400mm top of shelf shall be made of nylon sheet. Each shelf is fitted with 4 nos. 40 watts fluorescent light. Nylon wheels provided for easy movement without any scratch on the floor with Photoporiodic time and 3, 4 and 5 U V light in each unit.

No.of Shelves 4 5 6

Sterilizer Pressure Cooker Type (Electrically Operated)

This Sterilizer is made of Aluminium for quick transfer of heat, which generates steam under pressure. As soon as it reaches the right temperature the sterilizer are subjected to saturated steam environment for preset specified time. It has double protection for safety

Sterilizer pressure cooker type complete made of aluminum bowl. Electrically operated.

"NSW" Freeze Dryer covers a range of application from multiuser centralized laboratory application, pilot plant determination etc. made of mild steel duly powder coated. insulation of pre freezing chamber is done by puff. This unit is mounted on castors. The unit has hermetically sealed CFC Free compressor maintains temperature upto minus 40 C . Trap is given at non magnetic stainless steel dished bottom for complete effluent removal. Refrigerant coils made of copper are heavily insulated for maximum efficiency. Temperature control by Electronic Controller Cum Indicator. Vacuum Drum is made of non-magnetic stainless steel with Perspex top cover and incorporates 8/12" Quick seal valves/Ports for manifold drying. Double stage Vacuum pumps with gas ballast giving vacuum 1 x 10-3 torr module gauge. Sample port having 12.5mm outer dia provided for quick drying . Electronic Vacuum indicator, Pirani gauge is used. Specially designed temperature indicator to read temperature as low as 40 C, mounted on front panel. with 3 step automatic voltage stabilizer. Suitable to work on 220V, single phase, 50 HZ A.C. supply.

A Large capacity washer especially recommended for serological, bacteriological or clinical laboratory. It operates on a siphoning principle to send a continuous flow of water over the through the pipettes. At normal pressure the water is completely changed in cycles of about one minute. Even at reduced pressure this washer operates efficiently. In consist of a stainless steel washing cylinder 56 cm. Height into 15cm in diameter mounted in a base 26.2cm in diameter, and a removable pipette holder, which is 13.75cm dia. The holder is made of stainless steel with a heavy wire-mesh bottom, rolled in and spot welded for strength and durability, the cylinder has a 1.25cm inlet with a removable hose nipple for attaching to permanent dram if desired. Will accommodate pipettes up to 37.5cm in length.

COMPLETE (STAINLESS STEEL)

This is general purpose Hot Plate having maximum temperature 370 Deg. C with Electronic digital temperature controller cum indicator. Top of hot plate is made of aluminum dicast

Clean Room Sterile Dynamic Pass through box is self-contained units with class 100 laminar air flow unit installed at entrance to the clean rooms. They minimize the amount of particulate contamination entering the clean room by reducing the operator traffic. The laminar flow in the pass box starts running. When the doors are opened for material transfer in order to maintain air cleanliness required for the product which is equipped with a mechanical interlock system that prevents both the doors from being opened at the same time.

Construction details :- Unit has double walled construction.

Salient Features:-Electromagnetic InterlockingFloor mounted designMaximum chemical resistance constructionModular & Economical

These are required in the following applications:- Medical DevicesVaccine ManufacturersPharma Companies and other related applications

Complete made of Stainless Steel 304 qlty.

Fluid Warming Cbainet (Super Deluxe Model)

Double walled inside made of stainless steel 304 qty. and outside of Mild Steel Sheet furnished in Epoxy Powder Coating.The gap of75mm between two walls is fitted with pure mineral wool. Synthetic rubber gasket is provided on the door for better grip This incubator has double door outer is metal door and inside is glass door in stainless steel frame. There will be no glass window outside. If, you require glass window outside please specify while placing order. In this Case we shall not provide inside glass door. Heating elements are placed in ribs at the bottom and sides. Two adjustable air ventilators are placed near the top of the sides. The temperature is controlled by an Electronic microprocessed Temperature Controller cum Indicator from few C above ambient to 80 deg. C with sensitivity of plus minus 0.5 deg. C may be increased upto 100 C on request.Supplied complete with two pilot lamps, aircirculating fanperforated shelves adjustable at any level, having arrangement to fit the automatic timer to work on 220/230 volts A.C. only with cord and plug.

Option:

Microprocessed PID Controller having 4 ramp & 4 soak profile having set mode, alarm parameter, configuration parameter, profile parameter, set point profile, Pv error indicator, parameter for locking etc. Alarm: It is possible to provide electronic alarm if, temperature deviates more than +/- 1 C to cost extra. Automatic timer electronic 999 mts. to extra cost

Double walled inside made of thick Anodized Aluminium/Stainless Steel and outside made of Mild steel and painted in Epoxy Powder Coating. The gap of 75mm between two walls is filled with pure mineral wool. Synthetic rubber gasket is provided on the door for better grip. This incubator has double door outer is metal door and inside is glass door in stainless steel frame. There will be no glass window outside. If, you require glass window outside please specify while placing order. In this Case we shall not provide inside glass door.

Heating Elements are placed in ribs at the bottom and sides. Adjustable air ventilators are placed near the top of the sides. Built in Horizontal L shaped thermometer 0 to 110 C. is also provided.

The temperature is controlled by a Precision Thermostat from 10 C above ambient to 70 C with sensitivity of plus minus 0.5 C. Supplied complete with two pilot lamps , thermostat, perforated shelves adjustable at any level having arrangement to fit the automatic Timer to work on 220/230 volts A.C. cord and plug.

Option: Automatic timer mechanical 60 or 120 minutes at an extra cost

These work stations are used for examination specimens in pathology department, Powerful blowers sucks out the contaminated air and formalin vapor from the worktable.It is made of high qualities stainless steel sheet. Negative pressure of work station in maintained by highly efficient centrifugal blower. Work area is illuminated by fluorescent light. UV germicidal light is also fitted in this area. This grossing table is supplied with magnifying glass, magnetic instrument holder light flexible arms. paper towel holder, Polypropylene cutting board, sink and mixer tap for hot and cold water, sprinklet system, adjustable valve for bath sanitation located below the perforated working plates storage compartment under table, waste bin and a small weighing scale.

Side window & are made of poly carbonates which may be taken out to clean it

CALTAN - quality Laboratory Refrigerators offer high capacity and excellent temperature control at an affordable price. This Refrigerators are suitable for storage of vaccines, Reagents, Cultures, medicines, storing blood plasma and Blood samples. Temperature range adjustable from + 2.0 C to + 8.0 C temperature controller includes digital temperature display of set value and process value, Forced air circulation for maximum temperature uniformity. Temperature alarm system with adjustable high/low alarm limits, includes audible and visual warning.

This is double walled inside made of stainless steel 304 qlty. and outer is made of mild steel duly powder coated. It will have 75mm high-density puff insulation. This chamber has got a lockable door with plastic magnetic gasket. It offer a microprocessor temperature controller with maximum temperature uniformity with heavy duty forced air refrigeration system. Supplied with 3 or 4 removable perforated staibless steel 304 qlty shelves.

One sealed CFC free compressors with all its protective devices along with fan cooled condensing coil are placed below the working chamber for faster cool down and recovery times by heavy refrigerations . CFC free (Environmental Friendly ) refrigerant are used to cool down the temperature automatic/ manual deep frosting and condensed melt water evaporation system are done for longer life of compressor . Inside air circulating system is provided by 2 nos F.H. Moptor's Fan which keeps uniform temp. throughout the chamber.

Above Pharmacy Refrigerator shall be complete with following special features:-

1. perforated castor mounted
2. adjustable shelves
3. battery backup for display and alarms
4. control panel with temperature alarm, on/off switch and digital thermometer
5. interior lighting , manual defrosting arrangement
6. Adequate circulation of air to ensure even cooling
7. door with lock .
8. control panel with temperature alarm, on/off switch with power on indicator, digital thermometer, temperature display

Large size of Pharmacy refrigerator may be manufactured on customer requirements.

NSW walk in chamber are designed for simulating, monitoring to control environmental conditions. These chambers are double walled and modular in construction, easy to assumable at site. Size of chamber can be made as per customer requirement. Air circulation is made to create uniform temperature under RH inside.

Construction:Double wall prefabricated modular panels with PUF insulation. In GIMP model we shall provide inside 316 qlty. stainless steel cuter 304 qlty. Refrigeration system with spit type condensing Unit having (CFC free refrigerant) are placed outside the laboratory area Heating system consists of SS tubular heaters. Humidity inside the chamber is created by steam injection - Boiler and water reservoir made of stainless steel with heater with low water cut off. These chambers are designed as per ICH guidelines to meet WHO and USFD A specifications.

This Oven has double walls with an inner chamber made of Aluminum/Stainless Steel . Outer surface of Mild Steel and painted in Epoxy Powder Coating . The gap between walls is filled with special grade Mineral Wool which helps proper insulation and avoids loss of energy. In the inner chamber 2/3 removable shelves are provided. The is fitted with heavy caste chromium plated hinges with a spring and automatic roller to and fro latch. Synthetic rubber gasket is provided on the door for better grip.

The temperature is controlled by a precision Thermostat working in the range of 50 C. to 250 C in the variation up to plus minus 2 C . The inner chamber is heated with the help of coils heaters placed at the bottom with three control switch (Rotary Switch). For low, medium and high wattage .Control panel is located directly beneath the door provided with two neon pilot lights which indicate control cycles as well as mains. Temperature control knob graduated in centigrade , wattage controller knob marked Off, low, Medium and high. Complete with adjustable shutters near the top for ventilation, shelves wire and plug . To work on 220/230 volts A.C. but without thermometer.

Electronic digital temperature controller-cum-indicator can not be fitted in Hot Air Oven.

Double walled inside made of thick anodized Aluminum/Stainless Steel and outside and Mild Steel furnished in Epoxy Powder Coating. The gap of 75mm between two walls is filled with pure mineral wool. Synthetic rubber gasket is provided on the door for better grip.

Heating elements are placed in ribs at the bottom and sides. Adjustable air ventilators are placed near the top of the sides,

The temperature is controlled by an Electronic Digital Controller cum Indicator from room few C above ambient to 250 C with sensitivity of plus minus 0.5 deg. C . Supplied complete with two pilot lamps , perforated shelves adjustable at any level having arrangement to fit the automatic timer to works on 220/230 volts A.C. cord and plug. Complete with air circulating fan.

Option: Microprocessed PID controller having 4 ramp & 4 soak profile having set mode, alarm parameter, configuration parameter, profile parameter, set point profile, Pv error indicator , parameter for locking etc.

Alarm:It is possible to provide electronic alarm, if temperature deviates more than 5 C to cost extra

This is triple walled, inside made of stainless steel and outside made of mild steel painted in dark chocolate colour. Insulation between the two walls is filled with mineral wool. It is fitted with Electronic Digital temperature indicator cum controller and circulation fan also to get uniform temperature form plus/minus 3 deg. C. above ambient to 250 deg. C. These dryer are available in capacity of 3, 4, 6 & 9 trays with one No. M.S. drip tray.

Option: Microprocessed PID controller having 4 ramp & 4 soak profile having set mode, alarm parameter, configuration parameter, profile parameter, set point profile, Pv error indicator , parameter for locking etc.

Timer: Automatic timer electronic 999 mts to extra cost.

Alarm:It is possible to provide electronic alarm, if temperature deviates more than 5 C to cost extra.

3 heavy duty mild steel shelves. Temp. is being controlled by micro processed digital temp. controller cum indicator.

This is triple walled, inside and outside mild steel painted in dark chocolate colour & trays are made of Aluminium having size 800 x 400 x 30mm . Insulation between the two walls is filled with mineral wool. It is fitted with Microprocessed Electronic Digital temperature indicator cum controller and circulation fan also to get uniform temperature form plus/minus 3 deg. C. above ambient to 250 deg. C. These dryer are available in capacity of 12, 24, 48, 96 & 192 trays to work on 220v/440v A.C.

Option: Microprocessed PID Controller having 4 ramp & 4 soak profile having set mode, alarm parameter, configuration parameter, profile parameter, set point profile, Pv error indicator. parameter for locking etc.

Alarm: It is possible to provide electronic alarm if, temperature deviates more than 5 C tc cost extra.

Automatic timer electronic 999 mts. To extra cost.

Usage of Machine

Machine is used for endurance testing various machines Food Industry, AutomobileIndustries etc.

Construction:This is double walled cabinet insulated with 125mm thick puff between interior and exterior walls. Outer chamber made of Mild Steel and painted in Epoxy Powder coating in white colour. The inner chamber shall be made of Stainless Steel 304 qlty. Outer double walled metal door with MAGNETIC GASKET and lock & key. The chamber will have strong base for fitting your fixture.

This chamber shall be supplied with temperature controller. It will incorporate one compressors with all its protective devices along with two fan cooled condensing coil just below the working chamber. This chamber will have air circulating fan from the top of the cabinet. The chamber will have 2 dia hole from one side for feeding cables. Control panel shall be provided at the side of the chamber with three indicators one for main, one for heating, and one for cooling and a digital volt meter.

Dual electric digital temp. controller to control temperature from minus 40 C to + 110 C +/- 5 C . Humidity controller (Electronic) with control for dry & RH which will show present value and set value to maintain 95% humidity at 37 C . this chamber shall work on 440 Volts 3 phase 4 wire ststem.

2 METER X 2 METER X 2 METERCost for the chamber

Option:Independent display for temperature & % RH. Self tune PID control loop for temperature & % RH. Heater and humidifier control outputs which will have serial communication port RS 484, 2 wire, half duplex, start - stop synchronized safety standard meets EN-61010 with temperature alarm system having adjustable high/low alarm limits includes audible & visual warning to cost extra.

Note:Temperature range, in cool and heat can be given & manufactured as per customers requirement.

The purpose of stability testing is to provide evidence on how the quality of a drug substance or drug product varies with time under the influence of a variety of environmental factors such as temperature, humidity, and light, and to establish a re test period for the drug substance or product under recommended storage conditions. Hence, Pharmaceutical Stability Chamber serves as an important quality attribute for the product. "Calibration / Validation" Calibration

• Temperature sensor probe calibration with traceability to ERTL
• Temperature controller calibration with traceability to ERTL

Validation

• IQ, OQ, PQ and DQ documentation and protocols shall be provided with equipment.
• Documentation shall be given after supply & Installation.

Performance Qualification with Temperature Mapping. The performance Validation Test consists of one cycle at any one temperature point for an 8- hour period.

These shakers are generally required in the life sciences & Biotechnology. This series of shaker include Hybridization Incubator. The laboratory series of shakers are designed critically of operation for the typical research job. Even shaker are developed as per customer requirement. These shakers have speed range of 50-350 R.P.M. clamp capacity depends on size of the platform of shaker. It has optional arrangement to fit Mechanical or digital timer Digital RPM meter.

SIZEs AVAILABLE