Our Products
Feature |
Two loop addressable fire detection panel packed with features not usually associated with smaller systems, providing a high quality solution at exceptionally good valueLoop capacity 477 intelligent devices30 logical configurable zonesPAS and Acknowledge FunctionDuplicate address reportMismatch device type reportDirty Detector ReportingOne Man Test FunctionGraphical LCD DisplayZone indication and manual intervention panelNet-workable with all GST intelligent fire panelsProgrammable from PCBuilt-in RS485 repeater output (Maximum 10 repeaters)Optional GMC graphic stationOptional Panel PrinterAdvanced user friendly programming software including Fuzzy LogicOptional protection of re-programmingApproved by LPCB |
Standard: EN54-part 5 and part 7 |
Operating Voltage: 24VDC |
Standby Current: 0.1mA |
Alarm Current: 30mA |
Temperature: -10 +50 |
Relative Humidity: 95% |
Dimensions: Diameter 100mm, Height 56mm |
Ravel Indian Manufacturer, International standard. |
Switch Mode Power Supply. |
Modular Construction, Serviceable. |
Surface Mount Technology. |
Battery polarity & deep discharge protection. |
As per IS -15908: 2011 Standard. |
16 X 2 Dot Matrix LCD Display. |
Standby battery backup with built in charging. |
Fire / Fault status in unambiguous colored LED indication. |
Switch Mode Power Supply. |
Tactile Keypad for easy panel operation. |
System on indication. |
Main, Standby status indication. |
Low Battery visual warning with audible tone. |
Relay output for actuators for Fire and Fault. |
Lamp Test facility |
Zone wise one man walk Test Facility. |
Zone wise Isolation facility with loop voltage cut off. |
Compatible to all type of Conventional Detectors. |
Optional Zone Wise Sounder / Zone Wise Contact. |
Micro-controller based |
25 zones |
16 zones programmable as delay, immediate, panic, part and staff |
8 zones dedicated for wireless keyfobs & wireless panic switches |
1 dedicated tamper zone |
Secure code hopping technology |
Onboard 16 button keypad |
4 line back lit LCD display |
All sensors are configured through easy and secure learning process |
Wireless RF Key Fob with instant arm, delay arm, part arm, disarm and panic alarm buttons |
Supervised sensors with periodic health check with control panel |
Sensor low battery indication displayed on control panel |
Automatic arming and disarming at pre-programmed times |
Programmable weekly holiday for automatic disarming feature |
Two user codes - master and staff |
Part and Full arm modes for convenient daily use |
Automatic re-arming in case of alarm at which point open zones will be bypassed |
System goes into alarm state after three incorrect code attempts |
Previous arm status (armed or disarmed) is retained when panel is re-powered |
Distinct interrupted siren for fire alarm |
Inbuilt battery backup for internal clock |
Battery strength displayed on LCD screen with audio warning for low battery |
Power failure, blown fuse, low battery indication on LCD display |
Open zones are indicated on LCD display |
Independent entry and exit delay times programmable from 2 to 255 seconds |
Programmable sounder time from 2 to 20 minutes |
3 status LEDs armed, power and error |
Inbuilt lithium battery pack |
Can omit one or more zones |
Night mode arming to convert delay zones into immediate zones |
Intrusion log with time and date |
Panic and Quick Arm keys |
Non-volatile memory restores multiple programmable settings in case of complete power reset |
24 hour active zones are bypassed if open after sounder automatically switches off |
In-built tamper switches |
Simple to install and program |
Eye catching slim sleek design |
Premium white ABS housing with aesthetic brushed stainless steel front panel |
Micro-controller based |
8 zones |
Inbuilt GSM based speech and SMS dialer |
8 zones programmable as delay, immediate, panic or fire |
Separate remote key pad with 16x4 LCD display |
18 key back lit key pad |
Can attach up to 3 additional LCD display remote key pads |
3 status LED armed, power and dialing |
Two user codes master and servant |
Part arm |
Automatic arming |
Automatic disarming |
One day holiday programmable for automatic disarming feature |
Can be operated through mobile or telephone line using DTMF instrument |
Panel can be armed and disarmed through telephone |
Code can be changed through telephone |
Any 8 electrical devices can be switched ON or OFF through telephone |
These electrical devices can also be switched ON or OFF through a remote key pad |
Armed light output |
Built in battery backup provision |
Zone omitting facility |
Silent arming |
Night mode arming |
Intrusion log with time and date |
Dedicated panic, fire and quick arm keys |
Silent dialing |
Power failure indication |
Blown fuse indication on LCD display |
Non-volatile memory |
Open zone indication on LCD display |
Automatic re-arming after an intrusion |
System goes into alarm state after three incorrect code attempts |
Previous state (armed or disarmed) retained when panel is re-powered |
Chime in zone number 1 |
Chime is programmable for each independent remote key pad |
Distinct interrupted sounder output for fire alarm |
Battery strength display with audio indication in case of low battery |
GSM signal strength display |
Walk test |
Individual zone status is indicated on display |
Independent entry delay time 2 to 255 seconds |
Independent exit delay time 2 to 255 seconds |
Sounder time 2 to 20 minutes |
Multiple sounder outputs |
In-built tamper switch |
Main control station panel in elegant white ABS body |
Remote key pad housed in sleek white ABS body with key pad cover |
Micro-controller based |
25 zones |
16 zones programmable as delay, immediate, panic, part and staff |
8 zones dedicated for wireless keyfobs & wireless panic switches |
1 dedicated tamper zone |
Secure code hopping technology |
Onboard 16 button keypad |
4 line back lit LCD display |
All sensors are configured through easy and secure learning process |
Wireless RF Key Fob with instant arm, delay arm, part arm, disarm and panic alarm buttons |
Supervised sensors with periodic health check with control panel |
Sensor low battery indication displayed on control panel |
Automatic arming and disarming at pre-programmed times |
Programmable weekly holiday for automatic disarming feature |
Two user codes - master and staff |
Part and Full arm modes for convenient daily use |
Automatic re-arming in case of alarm at which point open zones will be bypassed |
System goes into alarm state after three incorrect code attempts |
Previous arm status (armed or disarmed) is retained when panel is re-powered |
Distinct interrupted siren for fire alarm |
Inbuilt battery backup for internal clock |
Battery strength displayed on LCD screen with audio warning for low battery |
Power failure, blown fuse, low battery indication on LCD display |
Open zones are indicated on LCD display |
Independent entry and exit delay times programmable from 2 to 255 seconds |
Programmable sounder time from 2 to 20 minutes |
3 status LEDs armed, power and error |
Inbuilt lithium battery pack |
Can omit one or more zones |
Night mode arming to convert delay zones into immediate zones |
Intrusion log with time and date |
Panic and Quick Arm keys |
Non-volatile memory restores multiple programmable settings in case of complete power reset |
24 hour active zones are bypassed if open after sounder automatically switches off |
In-built tamper switches |
Simple to install and program |
Eye catching slim sleek design |
Premium white ABS housing with aesthetic brushed stainless steel front panel |
Fail safe operation | ||
Low Temperature, safe & Durable | ||
Low Power, Environmental Protection | ||
Reverse current protection PCB | ||
Superior Strength Aluminum Alloy, Solid Stainless Steel Bolt |
Technical Specification | ||
---|---|---|
Dimension | Magnet(L X W X H ) | 250 X 42 X 26 mm |
Armature Plate(L X W X H ) | 180 X 38 X 11 mm | |
Current | 450 mA | |
Power | DC 12 V | |
Holding Force | 230 Kg | |
Holding Capacity | 600 lbs | |
Red | Positive | |
Black | Negative | |
Environment | Temperature | 10°C - 55°C |
Operating Humidity | 0%-95% (Non-Condensing) | |
Suitable For | Wooden Door,Glass Door,Metal Door | |
Optional Accessories | L Bracket ,U Bracket ,ZL Bracket ,U Bracket for Glass Door |
24 Vdc electromechanical barrier for intensive use with control panel with 433.92 MHz radio receiver and integrated battery charger. |
Power range switching extended from 100 to 250 Vac, 50/60 Hz to reduce standby power to a minimum. |
Control panel with LCD display. Possibility of self-testing the parameters and checking the condition of the safety devices (photo test). Compatibility with Advantouch device. |
Option to install FTC.S photocells using concealed system so that they are perfectly integrated. |
Integrated absolute encoder, which ensures greater precision in slowdowns and advanced control of the boom movement so that it never loses the reference position of the boom even if there is a power cut or the automatic device is released |
Integrated STC System for precise torque calculation. |
Serial connection with SIS accessory data sheet, for fast and easy connection for operation in paired boom mode. |
Fast-acting release. |
Integrated flashing lamp (requires EVA.LAMP accessory data sheet) |
UL Approved. |
Dual LEDs for 360 visibility. |
Advanced detection and communication protocol. |
Easy installation and maintenance. |
Sleek low-profile housing design. |
Regular 100mm base. |
Ravel Indian Manufacturer, International standard. |
Switch Mode Power Supply. |
Modular Construction, Serviceable. |
Surface Mount Technology. |
Battery polarity & deep discharge protection. |
As per IS -15908: 2011 Standard. |
16 X 2 Dot Matrix LCD Display. |
Standby battery backup with built in charging. |
Fire / Fault status in unambiguous colored LED indication. |
Switch Mode Power Supply. |
Tactile Keypad for easy panel operation. |
System on indication. |
Main, Standby status indication. |
Low Battery visual warning with audible tone. |
Relay output for actuators for Fire and Fault. |
Lamp Test facility |
Zone wise one man walk Test Facility. |
Zone wise Isolation facility with loop voltage cut off. |
Compatible to all type of Conventional Detectors. |
Optional Zone Wise Sounder / Zone Wise Contact. |
UL Approved. |
Dual LEDs for 360 visibility. |
Advanced detection and communication protocol. |
Easy installation and maintenance. |
Sleek low-profile housing design. |
Regular 100 mm base. |
Phone Features | Call Hold Mute Do Not Disturb Speed Dial Hotline Redial Call Back Auto Answer Call Forward Call Waiting Call Transfer Room Monitoring Conference Directory Call Logs Paging Dial-by-Name |
Call Management | Message Wait Lamp Ringer Lamp Voice Mail Call Pickup Group and Selective Paging |
Display | 6 Line and 2 Line LCD with Blacklisted for Incoming/Ongoing Call, Mute, Hold Intuitive User Interface with Icons Multiple Languages Caller ID with Name, Number |
Physical Features | 48 keys1 x RJ9 Handset Port1 x RJ9 Headset Port Dimension (L x B x H): 240 X 200 X 41 mm |
Mechanical | Weight: 1.18 Kgs Installation: Wall Mount, Table-top Color: Black |
Environmental | Operating Temperature Range = 0 to 45C Storage Temperature = 0 to 55C Operating and Storage Humidity = 5 to 95%, RH, Non-Condensing |
Green/red LED indication for lock status | ||
Design with no Mechanical Bolt | ||
Voltage and current spike protection PCB | ||
Superior Strength Aluminum Alloy, Solid Stainless Steel Bolt | ||
Silent operation: no humming o |
Technical Specification | ||
---|---|---|
Dimension | Magnet(L X W X H ) | 250 X 42 X 26 mm |
Armature Plate(L X W X H ) | 180 X 38 X 11 mm | |
Mounting Plate(L X W X H | 250 x 25 x 6mm | |
Current | 500 mA | |
Power | 12 V | |
Holding Capacity | 230 Kg | |
Holding Force | 600lbs | |
Environment | Temperature | 10°C – 55°C |
Operating Humidity | 0%-95% (Non-Condensing) | |
Optional Accessories | L Bracket ,U Bracket ,ZL Bracket | |
Suitable for | Wooden door, Glass door, Alluminium door, Fireproof door | |
IP Technology on Existing LAN/WAN |
Industry Standard CAT5 and CAT6 Wiring |
Installation near the Door Reduces Wiring and Improves Reliability |
PoE Powers PANEL, Readers and Locks, no Need of Local Power Point or Backup |
Neat, Elegant, Reliable and Easy-To-Maintain Installation |
Distributed Architecture; Robust Security |
Compact, Modular and Easy to Scale |
Industry Standard DIN Rail Mounting |
COSEC PANEL integrates up to 255 Door Controllers with interlinked value added features. |
Centralized Management and Control using COSEC PANEL Web Pages from anywhere |
Technical Specification
Variants | COSEC PATH DCCE | COSEC PATH DCCM | COSEC PATH DCCI |
---|---|---|---|
Credential Support | RFID Card | RFID Card | RFID Card |
Card Type | EM Prox | Mifare Smart | HID iCLASS, HID Prox |
User Capacity | 10,000 | 10,000 | 10,000 |
Cards Per User | Two | Two | Two |
Events Buffer | 50,000 | 50,000 | 50,000 |
RS-485 | Yes (115.2Kbps) | Yes (115.2Kbps) | Yes (115.2Kbps) |
Battery Backup | No | No | No |
Ethernet | Yes (10/100Mbps) | Yes (10/100Mbps) | Yes (10/100Mbps) |
PoE | Yes (IEEE 802.3 af) | Yes (IEEE 802.3 af) | Yes (IEEE 802.3 af) |
Exit Switch | Yes | Yes | Yes |
Door Status Sense | Programmable NO, NC and Supervised | Programmable NO, NC and Supervised | Programmable NO, NC and Supervised |
Door Lock Relay | Form C and SPDT Relay (Max 1A@30 VDC) | Form C and SPDT Relay (Max 1A@30 VDC) | Form C and SPDT Relay (Max 1A@30 VDC) |
Door Lock Power | Internal 12VDC @ 0.5A or External | Internal 12VDC @ 0.5A or External | Internal 12VDC @ 0.5A or External |
Reader Interface types | RS-232 and Wiegand IN/OUT | RS-232 and Wiegand IN/OUT | RS-232 and Wiegand IN/OUT |
Buzzer | Yes | Yes | Yes |
LED | Single LED (TriColor) | Single LED (Tri-Color) | Single LED (TriColor) |
CPU | 32Bit Microcontroller | 32Bit Microcontroller | 32Bit Microcontroller |
Flash Memory | 512kB Internal Memory + 4MB External Flash | 512kB Internal Memory + 4MB External Flash | 512kB Internal Memory + 4MB External Flash |
RAM Memory | 128kB SRAM | 128kB SRAM | 128kB SRAM |
Input Power | 12VDC @ 2A | 12VDC @ 2A | 12VDC @ 2A |
Humidity | 5% to 85% RH Non- condensing | 5% to 85% RH Non- condensing | 5% to 85% RH Non- condensing |
Tamper Detection | Yes | Yes | Yes |
IP65 | Verified | Verified | Verified |
Certification | CE and BIS | CE and BIS | CE and BIS |
Dimension (mm) | 50.5X137X34 | 50.5X137X34 | 50.5X137X34 |
Weight (kgs) | 0.18 | 0.18 | 0.18 |
Audio Line can be utilised wherever continuous audio recording is required. The logger logs the analog audio signals from any equipment connected to it as 'line-in'. Xtend provides USB-based Audio Logger in 1/2/4/8/12/16 upto 256 ports and more. |
This logger toolkit can be programmed in such a way that it initiates the logging immediately after a keypress. There are 4 ways in which Xtend Logger commences the recording process. They are: |
Timed Recording: Logs the audio everyday, especially, during a particular time schedule. |
Voice Activated Recording: Logs the audio when specific voice/words are recognised. |
Continuous Recording: Logs audio wherever 24x7 logging is needed. |
Externally-triggered Recording: Logs the audio, if and only if an external trigger occurs, such as a switch is turned on. |
Just like the other models of Xtend Voice Logger, audio model is a passive logger that does not tamper with the voice quality or the signalling system. Again, no change is required in the existing system configuration to install this model of the logging system. |
Apart from hardware, Xtend Voice Logging Solution software needs to be loaded to generate the reports and details of logging. For the same, we require an ordinary PC with 2+ GHz processor capability and atleast 80GB hard disk storage space to store the voice logs. Windows XP Professional/2000/2003 Server operating system with a minimum of 512 MB RAM is required for proper functioning of the system. A CD/DVD writer avails to store backups whereas a Network Interface Card serves to access remotely the browser-based interface. |
Gesture-based, multitouch-capable capacitive touch screen |
5-inch color LCD (720 x 1280 pixel), 9:16 aspect ratio |
On-screen virtual keyboard |
1 USB 2.0 Type A-compliant port USB battery charging BC1.2 compliant (requires full Class 4 power input on LAN IN for operation) |
Integrated Bluetooth 4.0 and NFC |
3 multicolored capacitive-touch mute indicators |
Unicode UTF-8-character support |
User interface localized in Arabic, Chinese, Danish, Dutch, English (Canada/ US/UK), French, German, Italian, Japanese, Korean, Norwegian, Polish, Portuguese, Russian, Slovenian, Spanish and Swedish |
3 cardioid microphones |
Loudspeaker - Frequency: 100-22, 000 Hz - Volume: 92 dB at 0.5m peak volume |
6m/20-foot microphone pickup range |
Supported codecs: - G.711 (A-law and -law) |
Polycom Siren 7 (16kbps) |
Polycom Acoustic Clarity technology provides full-duplex conversations, acoustic echo cancellation and background noise suppression - Type 1 compliant (IEEE 1329 full duplex) |
Polycom NoiseBlock |
Voice activity detection |
Comfort noise generation |
DTMF tone generation (RFC 2833 and in-band) |
Low-delay audio packet transmission |
Adaptive jitter buffers |
Packet loss concealment |
Bluetooth device pairing for wideband speech and multimedia streaming (HFP/AD2P) |
Call handling features |
1 line (registration) |
Shared call/bridged line appearance |
Distinctive incoming call treatment/call waiting |
Call timer and call waiting |
Call transfer, hold, divert (forward), pickup |
Called, calling, connected-party information |
One-touch speed dial |
Do-not-disturb function |
Local configurable digit map/dial plan |
Corporate directory access using LDAP |
Visual conference management |
LAN IN: Built-in auto-sensing IEEE 802.3at. PoE Device (Class 4) (requires full Class 4 power input on LAN IN for operation). Backward compatibility with IEEE 802.3af. |
LAN OUT: Built-in auto-sensing IEEE 802.3af power sourcing equipment (requires full Class 4 power input on LAN IN for operation) |
Operating temperature: 0 to 40C (+32 to 104F) |
Relative humidity: 5% to 95% (non-condensing) |
Storage temperature: -20 to +70C (-4 to +160F) |
38.3 x 7.5 x 33.2 cm (15.1 x 2.9 x 13.1 in) |
Unit weight: 0.95Kg (2.1 lbs) |
48.3 x 11.5 x 39.4 cm (19 x 4.5 x 15.5 in) |
Box weight: 1.97 Kg (4.35 lbs) |
Telesoft large scale manufacturing units equipped with the latest technology and a team of highly IIT qualified professionals has earned us accolades to manufacture and supply of world class building Security Intercom System for over 3 decade. Telesoft system flexible flat numbering adjusts with any type of flat numbering scheme 2/3/4 digits. Specially for Hostel /Hospital/Hotel/Housing society/Office that has flats up to 64 lines. This model is available in configuration of 16, 32, 48 & 64 lines, using external power supply Model PS64. |
Features(This system has heart wining features like ) :
|
Technical Specification: Telesecure is based on Space division Matrix switching Technology using latest Microcontroller 51RD2 family. |
Ravel Indian Manufacturer, International standard. |
Switch Mode Power Supply. |
Modular Construction, Serviceable. |
Surface Mount Technology. |
Battery polarity & deep discharge protection. |
As per IS -15908: 2011 Standard. |
16 X 2 Dot Matrix LCD Display. |
Standby battery backup with built in charging. |
Fire / Fault status in unambiguous colored LED indication. |
Switch Mode Power Supply. |
Tactile Keypad for easy panel operation. |
System on indication. |
Main, Standby status indication. |
Low Battery visual warning with audible tone. |
Relay output for actuators for Fire and Fault. |
Lamp Test facility |
Zone wise one man walk Test Facility. |
Zone wise Isolation facility with loop voltage cut off. |
Compatible to all type of Conventional Detectors. |
Optional Zone Wise Sounder / Zone Wise Contact. |