Ahmedabad, Gujarat, India
Our Products
Improves Surface finish of top Rollers
No need for hazardous acid treatment
Can treat any type of Top Rollers
Auto feed magazine of ring frame top rollers
Up to 120 Ring Frame Top roll can be treated at a time
Continuous Process
Power 3.1 kw.
Having Liner Drive main unit
A.C. variable Driver
Grinding stone Force is, on Gravity Froce
Bracket for holding one any one make of card
Extra bracked for other make of card will be at extra cost
Also available for Tc 11 & Rieter c-70 Cards.
For Opening loose Roving waste
Better Griping thanks to special design of Feed Plate
Pinned type beater ensures zero fibre damage
Power 5.2 kw.
For checking eccentrincity and taper of all types of top Rollers
Fully Motorized, equipped with one dial gauge having motorized traverse.
For milling worn out flat ends, bring the original accuracy of Heel & Toe.
With fixed cam arrangement.
Novel arrangement of fix cam for accurate and easy Heel & Toe Milling.
Machine should be supplied with one pair of cam suitable for one make of card.
Control bar with supports and dial indicator.
The FEM-2 will mill flats types of 40 cards (60 version on request)
Two speed gear box to change RPM of cutter.
Clamping of flat by pneumatically operated clamp.
Pair of cam for any make of card.
Heavy duty butt welder suitable for heavy inter locking wire of blow room & also for matalic wire for card.
1.5 kW for card wires
3 kW for card wires & all heavy duty wires.
This machine eliminate Acid treatment machine or other highly toxic chemical coating used for preventing lapping tendency on cots.
The machines can process all types of cots like Draw frame, Combers, Sliver lap Ribbon laps and all the variety of cots from Ring frames & Speed frames.
Sutiable for all types of Ring Frame & Roving Frame Top Rollers
Capacity:up to 600 800 arbours/Hr
Both bearing lubricated simultaneously with exact quantity of grease
Prevents excessive greasing
Motor 0.37 kw .
Accurate & precise truing of Bottom rollers, Shafts etc.
Can handle rollers up to 40 mm diameter.
Hydraulic operated press
Eccentricity checking gauge is included.
With Three oil Tanks- For Topping Oil, Flushing Oil & Fresh oil.
Two Oiling Guns For Bolster Flushing and Filling bolster with Fresh oil.
Fine filter for flushing oil
Flushing oil tank capacity: 23 Litre.
Topping oil tank capacity: 13 Litre.
Used oil tank capacity: 9 Litre.
Eight arbours can be cleaned at a time
Sixteen powerful oil jets thoroughly clean the arbour to remove all old grease.
Arbours rotate during the flushing cycle Fully enclosed .
The OCFG-1 will grinding flat from all types of 40 card (60 version on request).
Full width on Card Grinding Roller for Rieter C-60 Card, mounted with Ceramic Stones.
Also available for 40 Card.
Dressing bed for stone dressing of On Card Flat Grinder for Rieter C-60 Card .
Greasing tank having 2 kg capacity (Approx).
Calibration system to control delivery of grease.
Machine is operated by single handle with dual function, arbour is pushed upward to the nozzle and pump the grease.
Fully automatic PLC control machine
Pneumatic cylinders for all actions
No need for manual hammering for clipping at both ends
Ensuring safety, thanks to safetylight curtain
Quick and easy pre-programmable for different make of cards flats
Carriage movement guides by LM guide for rigidity
Top pressing and clipping to the flat is simultaneous operation
ensures highest precision of clipping with respect to straightness of the flat bars
Also available for Rieter C-70 Card flat and Trutzchler TC 11 card flat, (PFC-4-60)
Motor 1.1 kw
Manual operated press.
For Truing the Bottom roller/Shafts .
Can handle rollers up to 40 mm diameter.
With a dial gauge to measure Eccentricity.
Suitable for mounting long cots ( Draw Frame, Comber ) with Aluminium core.
Possible to adjust stroke as per the cot length
Maximum pressure that can be exerted - 7.5 tons
Horizontal version available on request .
