Our Products
Details :
Strong, made of engineering plastic
Available in full, half and quarter circle.
Economical.
Popular for oil palm, vanilla, flowers etc.
Connection:5mm male thread.
Colour:Full circle low discharge DX-F-LD Blue
Full circle DX-F - Orange
Half circle DX-H - Green
Quarter Circle DX-Q Red
Material:Polyacetal
Pressure-bar | Discharge - l/hr | Dia – m | Radius - m | |||||
DX-F-LD | DX-F | DX-H |
DX-Q |
Std. | Low | Std. | Low | |
0.7 | - | 60 | 35 | 26 | - | 2.2 | 1.2 | 1.2 |
1.0 | - | 102 | 55 | 35 | - | 2.5 | 1.3 | 1.3 |
1.5 | 42.5 | 135 | 67 | 41 | 2.4 | 3.0 | 1.5 | 1.5 |
Special compound for strength, toughness and crack resistance.
To IS12786, amendment no.5 ISI marked.
Full range of fittings.
Emission Rate a
The original take-apart emitter.
|
Model FT 30 - volume of tank: 30 litres
Model FT 60 - volume of tank: 60 litres
Model FT 90 - volume of tank: 90 litres
Formed and welded from steel sheet 3mm thick, dished ends. Integral mounting base. Protected all over by heat fused epoxy/polyester powder coating, colour : orange. Outlet has stainless steel screen filler. Includes: drain valve, air valve, inlet and outlet connecting hoses each 1m length with " BSP fm connection both ends.
Applications |
Normal gauges are generally used for general applications where vibration & pulsating media is not a factor. |
Specifications |
Dial Sizes 50mm |
Steel with powder coating |
Brass or SS Working Parts |
1/8 bsp or npt connection |
Bottom Direct Mounting |
A very popular system with high quality couplers for agriculture and medium sized lantations.
Double Hooks coupling system with springs for extra security. |
Does not uncouple when pump restarts after power failure resist shocks |
High quality sealing ring lasts longer. |
SL system for normal use. SL-HP for higher pressures. |
ISI marked IS:14151 quality pipes. |
Wide range of fittings. |
Available sizes are 63, 75, 90, 110mm diameters. Maximum working Pressure: for 63 & 75mm 5.9bar and for 90 & 110mm 4.0 Bars |
Extremely strong system for large farms and plantations with high static heads.
Only two hooks (unlike three or four which are difficult to handle) for easy coupling/uncoupling.
Spring loaded hooks for security.
With different pipe ratings to cost effectively meet all pressure requirements.
Suitable for high pressure ratings.
Sizes up to 160mm diameter.
ISI marked IS:14151 quality pipes.
Very wide range of fittings.
Model, Cat. No.:1, 25mm 25AVRV
Instant and continuous vacuum relief
Large air chamber for air relief
Seal tight at 0.34 bar/5 psi
8 bar/125 psi working pressure
Max. operating pressure:10 bar/145 psi
Protection cap
Durable, weather resistant, corrosion
resistant
Construction : ABS plastic and elastomerseal
Inlet : 1 NPT male thread
Premier Souldered End Groove Clamp Coupled
Fast and simple to install
Foolproof jointing
Corrosion proof
Wide range of pressure ratings
Resistant to shock
Exceptional durability
Lowest lifetime cost
Widely used in developed countries for potable water supply, gas distribution, irrigation, mining and industrial
Removing The Hazards Of In-Field Butt Welding |
The PREMIER approach is the application of logic - rather than trying to provide ideal welding conditions in the field the process is reversed and pipes are welded under ideal conditions in the factory, tested, then taken to the field. Field butt welding is always a troublesome business requiring close supervision, protection from the elements, a generating set and has low productivity. If there is a failure during testing, the repair and rewelding are particularly complicated.
For low and medium pressure permanent mains, landscape irrigation and other piping applications
Manufactured to IS:4985 and ISI marked.
Solvent welded joints