Chennai, Tamil Nadu, India
Our Products
DESCRIPTION :
Sleeves for the connection of 35-50-70-95 mm cross section cables.
Complies with the requirements set forth in the standards:
EN 62.305
Made of Cu/Zn alloy (brass). Stainless steel hardware.
DESCRIPTION :
Useful for vertical fastening of masts to various structures.
Permits fastening 1'" and 2" tubes. Consult for other measurements.
Suppliable in Work, Plate or Double anchor versions.
Set of two pieces made of hot galvanized steel.
DESCRIPTION :
Fastener clamps for 30x2 cross section tape.
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/4
Made of Cu/Zn alloy (brass), stainless steel hardware.
Available with different anchoring types in M6 (plug, dowel screw, foot flange).
DESCRIPTION :
It detects and stores current spikes which circulate through the conductor.
A support fixture is included for a 8 to 10 mm diameter round cable.
DESCRIPTION :
Flat base support for horizontal surfaces for tube fastening, available
for 1'", 1'" and 2" tubes.
Made of hot galvanized steel
DESCRIPTION :
Adjustable support for 160-260 mm wide lintel tiles.
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/4
Made of hot galvanized steel.
With fastener clamp for 50-70-95 mm cross section cables.
DESCRIPTION :
Wall mounted grounding test joint, consisting of Cu/Zn alloy (brass) manual disconnection system and 160x118x75 mm PVC box, water resistant (IP 65). Stainless steel hardware.
Specially made for 50 mm cross section Cu cable down conductors.
Fittings also available for connection of 70 and 95 mm cross section cables and for copper tape 30x2 mm down conductors.
Complies with the requirements set forth in the standards:
UNE 21.186 NFC 17.102 EN 50.164/1 EN 62.305
DESCRIPTION :
Grounding connection bar consisting of copper bar, insulators and terminal connectors.
Complies with the requirements set forth in the standards UNE 21.186 NFC 17.102 EN 50.164/1 EN 62.305
Made of Cu (bar) and brass (terminals). Stainless steel hardware.
DESCRIPTION :
Very useful in any type of grounding (houses, antennas, machinery and instrumentation, etc.)
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/2
Models made of hot galvanized steel, stainless steel or copper- plated steel
DESCRIPTION :
3 m Masts.
6 m Telescopic Masts (in two sections with M12 coupler).
Models made of hot galvanized steel or stainless steel.
DESCRIPTION :
Logs the lightning strikes which occur within the external lightning protection system.
Complies with the requirements set forth in the standards:
UNE 21.186 NFC 17.102 EN 62.305
Range of Intensity:
1 kA (8/20 s) - 100 kA (10/350 s), according to EN 50.164/6
Valid for: Cable 50-95 mm, Rod 8-12 mm, Tape 30x2 mm.
DESCRIPTION :
Concrete support with black polyethylene sheath.
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/4
Allows fixing round conductors 35 to 95 mm on flat roofs.
DESCRIPTION :
Necessary to connect the air terminal receiver to the mast.
Facilitates the connection of the head to the conducting network.
Available in two models: for connection to cable or rod conductive networks and for connection to 30x2mm tape conductive networks.
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/1
Made of Cu/Zn alloy (brass).
Stainless steel hardware.
DESCRIPTION :
Useful for vertical fastening of masts to various structures.
Permits fastening 1'" and 2" tubes. Consult for other measurements.
Suppliable in Work, Plate or Double anchor versions.
Set of two pieces made of hot galvanized steel.
Braided bare electrolytic copper cable.
Complies with the requirements set forth in the standards:
NFC 17.102 UNE 21.186
EN 50.164/2 EN 62.305 (only cables 50 mm)
Mainly applied as a down conductor for lightning protection and
grounding systems.
DESCRIPTION :
Mineral composite to improve conductivity to ground.
With its use, low resistances are obtained in all types of groundings (houses, antennas, machinery and instrumentation, lightning rods, etc.)
Packaging made of recycled plastic, practical and easy to store.
DESCRIPTION :
Grounding connection bar consisting of copper bar and connection terminals for 35 to 95 mm cross section cables.
Complies with the requirements set forth in the standards:
UNE 21.186 NFC 17.102 EN 50.164/1 EN 62.305
Made of Cu (Copper). Stainless steel hardware.
DESCRIPTION :
Registry system for grounding installations.
High strength antiskid inspection chambers and covers.
Models made of polypropylene or concrete
DESCRIPTION :
Protection against transitory surges of general electrical facilities
connected to single-phase low voltage 230V mains power. Protector Type III (Fine protection).
Suitable for protection of equipment intended to be connected to an electrical installation (Category I, according to ITC-BT-23).
Model MCD-E, includes a front jack for connecting equipment to the electrical grid.
Technical specifications of the Absorber protectors:
Nominal Voltage: UN= 230V AC (50Hz).
Maximum working Voltage: UC= 275V AC (50Hz)
Nominal discharge Intensity: In(8/20 s)= 5kA
Maximum discharge Intensity: Imax(8/20 s)= 8kA
Response time: tA< 25 ns
Protection level: UP 1kV
Nominal load current: IL= 16 A (MCD-E model)
DESCRIPTION :
Mechanical protector for tape down conductors of external lightning protection systems, placed
at ground level.
Suitable for the protection of external down conductors, as recommended by the UNE 21.186 and NFC 17.102 standards.
Length 3 m.
Model made of 1 mm hot galvanized steel plate sheet. Masonry wall anchoring hardware included.
DESCRIPTION :
Ideal for the installation of grounding systems with high resistance terrain.
Models available made of Copper, Hot galvanized steel or Stainless steel*. (The stainless steel model is recommended by INGESCO for use only in very humid, marine or highly corrosive environments).
Stainless steel hardware.
Complies with the requirements set forth in the standards (except Stainless steel model):
UNE 21.186 NFC 17.102
Plate connection sleeve detail Ref. 119094 l EN 50.164/2 l EN 62.305 Large contact surface.
It is recommended to add the Quibacsol mineral compound in the insta llation, and also a humidifying tube accessory for maintenance.
Tape connectors specially designed for tapes 2 to 4 mm thick and 30 mm wide.
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/1
Models made of copper or Cu/Zn alloy (brass), stainless steel hardware.
DESCRIPTION :
Indicated for the connection of TV and communications antennas and cathodic protection.
Complies with the requirements set forth in the standards:
EN 50.164/3
Maximum intensity 50 kA, wave type 10/350 s.
Response voltage (1, 2/50 s) = 15kV
It can be supplied with terminal connectors (sleeves) for tape or for 50-70-95 mm cross section cables. Stainless steel hardware.
DESCRIPTION :
Flat base support, for fixing Franklin air terminals on horizontal surfaces.
Complies with the requirements set forth in the standards:
EN 62.305
Made of stainless steel and hot galvanized steel.
DESCRIPTION :
Fastener clamps for 50-70-95 mm cross section cables.
Complies with the requirements set forth in the standards:
EN 62.305 EN 50.164/4
Made of Cu/Zn alloy (brass), stainless steel hardware.
Pre assembled models with different anchoring types in M6 and M8 sizes
(plug, dowel screw, foot flange).
|
DESCRIPTION :
Mechanical protector for down conductors of external lightning protection systems, placed at ground level.
Suitable for the protection of external down conductors, as recommended by the UNE 21.186 and NFC 17.102 standards.
Length 3 m.
Model made with hot galvanized steel, containing 32 mm inner tube made of PVC.
Includes 3 clamps, plugs and dowel screws.
description :
lightning rod with non-electronicese(early streamer emission) system, standardized according norms une 21.186 and nfc 17.102.
adaptable to all types of buildings.
complies with the requirements set forth in the standards:
une 21.186 nfc 17.102 en 50.164/1 l en 62.305
product certification num. Es020609 issued by the certification entity bureau veritas international.
made of aisi 316 stainless steel and epoxy resin.
100 % efficiency, maximum durability.
does not need an external power supply.
guarantee of electrical continuity and operation after lightning strike,
in any atmospheric conditions.
DESCRIPTION :
Lightning rod with electronicESE(Early Streamer Emission) system, standardized according norms UNE 21.186 and NFC 17.102.
Adaptable to all types of buildings.
Complies with the requirements set forth in the standards:
UNE 21.186 NFC 17.102 EN 50.164/1 EN 62.305
Product certification num. ES020609 issued by the certification entity Bureau Veritas International.
Made of AISI 316 stainless steel.
100 % EFFICIENCY, maximum durability.
Does not need an external power supply.
Guarantee of electrical continuity and operation after lightning strike, in any atmospheric conditions.
description :
lightning rod with electronicese(early streamer emission) system, standardized according norms une 21.186 and nfc 17.102.
adaptable to all types of buildings.
complies with the requirements set forth in the standards:
une 21.186 nfc 17.102 en 50.164/1 en 62.305
product certification num. Es020609 issued by the certification entity bureau veritas international.
made of aisi 316 stainless steel.
100 % efficiency, maximum durability.
does not need an external power supply.
guarantee of electrical continuity and operation after lightning strike, in any atmospheric conditions.
