Ladder Type and Perforated Cable Trays in various sizes and shapes as required by customers for various load bearin capacities. These are available in painted, powder coated or  galvanized form as required by the customer.   Ladder Type and Perforated Cable Trays shown here (in Upturned position for better view) alongwith mounting Brackets. We supply complete installation material along with The cable tray.

Ladder type Cable Trays  and pendulums duly galvanized are made  for heavy loads and for external use.  These are also made of ‘C’ type channels or MS angles as required by customers and supplied with complete installation materials.

We Manufacture a new generation of cable entry systems that provide Perfect fit to all types of coaxial cables used in transmission, Rubber Boots that makes it water proof and weather resistance. The grade Of rubber used to manufacture boot excels in properties like heat Resistance, ozone resistance, weatherproofing and withstanding low Temperatures. Cable Entry Systems are available in various designs to suit customer requirements and specifications. They come with Six, Four, Three or Two boot Locations   The boots are easily detachable and replaceable. Boots with different designs are also available to suit the entry of different types of cables with a wide variety of designs and dimensions. In addition to the rubber boots, jubilee clamps are also provided to enhance fitment. Dummy boots are also provided in case if any cable entry site is not required in the installation.

After Preparation of cable, the Cable outer conductor/ Jointing Sleeve is tighten and blocked on 360 degree between the cone of the connector body and the flexible rear clamp, resulting in high grade mechanical retention and a perfect electrical continuity and complete shielding. All inner contacts are captivated, thus avoiding any risk of damage during coupling of male to female connectors.   We recommend three Grounding Kits per feeder run. One kit is required at the top, one at the bottom of the run, (plus one at 50 meters interval wherever applicable) and one at entrance to the equipment shelter.   Grounding Kit that have been specially tailored to each cable size can be installed very easily and rapidly, once the jacket is stripped at the required dimensions, one kit can be installed in less than three minutes. Kits are provided all hardware necessary to connect the ground wire to the tower ground bar.

Ladder Type and Perforated Cable Trays in various sizes and shapes as required by customers for various load bearin capacities. These are available in painted, powder coated or  galvanized form as required by the customer.   Ladder Type and Perforated Cable Trays shown here (in Upturned position for better view) alongwith mounting Brackets. We supply complete installation material along with The cable tray.

Ladder type Cable Trays  and pendulums duly galvanized are made  for heavy loads and for external use.  These are also made of ‘C’ type channels or MS angles as required by customers and supplied with complete installation materials.

We Manufacture a new generation of cable entry systems that provide Perfect fit to all types of coaxial cables used in transmission, Rubber Boots that makes it water proof and weather resistance. The grade Of rubber used to manufacture boot excels in properties like heat Resistance, ozone resistance, weatherproofing and withstanding low Temperatures. Cable Entry Systems are available in various designs to suit customer requirements and specifications. They come with Six, Four, Three or Two boot Locations   The boots are easily detachable and replaceable. Boots with different designs are also available to suit the entry of different types of cables with a wide variety of designs and dimensions. In addition to the rubber boots, jubilee clamps are also provided to enhance fitment. Dummy boots are also provided in case if any cable entry site is not required in the installation.

After Preparation of cable, the Cable outer conductor/ Jointing Sleeve is tighten and blocked on 360 degree between the cone of the connector body and the flexible rear clamp, resulting in high grade mechanical retention and a perfect electrical continuity and complete shielding. All inner contacts are captivated, thus avoiding any risk of damage during coupling of male to female connectors.   We recommend three Grounding Kits per feeder run. One kit is required at the top, one at the bottom of the run, (plus one at 50 meters interval wherever applicable) and one at entrance to the equipment shelter.   Grounding Kit that have been specially tailored to each cable size can be installed very easily and rapidly, once the jacket is stripped at the required dimensions, one kit can be installed in less than three minutes. Kits are provided all hardware necessary to connect the ground wire to the tower ground bar.