BOD Incubator is designed for low temperature incubation and routine determination of Bio - Chemical oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber of the BOD Incubator is made of richly anodized aluminum or highly polished stainless steel with self-support for wide range of self-spacing. Our offered BOD Incubator is supplied with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in white staving enamel paint or mat finished pestle color combinations. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5^oC to 50^oC 1^oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. The temperature can be regulated within the range by means of high precision double action thermo regulator. Inner air circulating system is provided to achieve uniform temperature in the whole chamber. A control panel is provided with various indicators such as on off switch, L - shaped thermometer, etc. The BOD Incubator is supplied with cord & plug, etc. The equipment is workable on 220V AC 50 Hz single phase. Details : Aluminum chamber sizes :

• 24" x 18" x 6" - 4 cubic ft.
• 33" x 20" x 16.5" - 6 cubic ft.
• 34.5" x 22.5" x 22.5" -10 cubic ft.
• 36" x 26" x 23" - 12 cubic ft.
• 27.5" x 25.5" x 35.5" -15 cubic ft.

S. S. chamber sizes :

• 24" x 18" x 6" - 4 cubic ft.
• 33" x 20" x 16.5" - 6 cubic ft.
• 34.5" x 22.5" x 22.5" -10 cubic ft.
• 36" x 26" x 23" -12 cubic ft.
• 27.5" x 25.5" x 35.5" -15 cubic ft.

Optional accessories if require with above at extra cost :

• Timer 0.24 hours day night cycle.
• Co₂/air mixer nozzle is provided.
• Internal illumination with 3 fluorescent tubes.
• Digital temp. Indicator-cum-Controller.
• Micropcessor PID digital temp. Indicator-cum-controller.
• Automatic Voltage Stabilizer 3-5 KVA (recommended must.)

ACuvetteis a kind of laboratory glassware, usually a small square tube, sealed at one end, made of plastic, glass, or optical grade quartz and designed to hold samples for spectroscopic experiments. The Cuvette is used for spectrophotometer, fluorometer, & tintometer. We offer a full line of optical Cuvette made from quartz, glass & IR cells. Our Cuvette is made of high-quality quartz and glass and is compatible with most spectrophotometers and fluorometers available in the markets. We offer equal or better quality of Cuvette than others but at the most affordable prices. This way, we have become the best option against the companies like NSG, Spectrocell, Hellma, and others.

We are R S Scientific Company. We are leading Cuvettes, Cuvettes Manufacturers, Plastic Cuvettes Suppliers, Disposable Cuvette Supplier India, Cuvettes Exporters, Buy Cuvettes, Best Cuvettes, Online Cuvettes, Cuvettes in Delhi, India.

Disposable Plastic Spectrophotometer Cuvette:-

1.) 4ML ( Cuvette, PS)

2.) 4.5ML (Cuvette, PS)

We are offering incubator, incubatorsstandard double wall fabrication. inner chamber made of out of richly anodized aluminum of highly polished stainless steel sheet and outer made out of thick mild steel sheet finished in white staving enamel paint or mat finished pestle color combinations. The gap is filled with special glass wool for temp. Insulation double walldoor with double glass window for observation in the chamber. Temperature range 5 c above ambient to 80c 2c controlled by a thermostat l - shaped thermometer is provided for taking temp readings. panel is provided with piolet lamps for mains& heaters, on-off switch, temp. Control' knob etc. The equipment is workable on 220 v ac 50 hz single phases. heating is achieved from 3 sides. Perforated all size in m.s. And s.s.

Product Description

We provide a proven range ofMeasuring Cylinders, which is fabricated from quality materials. The Measuring Cylinders are used to precisely measure out the volumes of objects for use in laboratories. Further, we offer Measuring Cylinders in various sizes and models to meet the requirements of our clients.

BOD Incubator is designed for low temperature incubation and routine determination of Bio - Chemical oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber of the BOD Incubator is made of richly anodized aluminum or highly polished stainless steel with self-support for wide range of self-spacing. Our offered BOD Incubator is supplied with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in white staving enamel paint or mat finished pestle color combinations. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5^oC to 50^oC 1^oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. The temperature can be regulated within the range by means of high precision double action thermo regulator. Inner air circulating system is provided to achieve uniform temperature in the whole chamber. A control panel is provided with various indicators such as on off switch, L - shaped thermometer, etc. The BOD Incubator is supplied with cord & plug, etc. The equipment is workable on 220V AC 50 Hz single phase. Details : Aluminum chamber sizes :

• 24" x 18" x 6" - 4 cubic ft.
• 33" x 20" x 16.5" - 6 cubic ft.
• 34.5" x 22.5" x 22.5" -10 cubic ft.
• 36" x 26" x 23" - 12 cubic ft.
• 27.5" x 25.5" x 35.5" -15 cubic ft.

S. S. chamber sizes :

• 24" x 18" x 6" - 4 cubic ft.
• 33" x 20" x 16.5" - 6 cubic ft.
• 34.5" x 22.5" x 22.5" -10 cubic ft.
• 36" x 26" x 23" -12 cubic ft.
• 27.5" x 25.5" x 35.5" -15 cubic ft.

Optional accessories if require with above at extra cost :

• Timer 0.24 hours day night cycle.
• Co₂/air mixer nozzle is provided.
• Internal illumination with 3 fluorescent tubes.
• Digital temp. Indicator-cum-Controller.
• Micropcessor PID digital temp. Indicator-cum-controller.
• Automatic Voltage Stabilizer 3-5 KVA (recommended must.)

ACuvetteis a kind of laboratory glassware, usually a small square tube, sealed at one end, made of plastic, glass, or optical grade quartz and designed to hold samples for spectroscopic experiments. The Cuvette is used for spectrophotometer, fluorometer, & tintometer. We offer a full line of optical Cuvette made from quartz, glass & IR cells. Our Cuvette is made of high-quality quartz and glass and is compatible with most spectrophotometers and fluorometers available in the markets. We offer equal or better quality of Cuvette than others but at the most affordable prices. This way, we have become the best option against the companies like NSG, Spectrocell, Hellma, and others.

We are R S Scientific Company. We are leading Cuvettes, Cuvettes Manufacturers, Plastic Cuvettes Suppliers, Disposable Cuvette Supplier India, Cuvettes Exporters, Buy Cuvettes, Best Cuvettes, Online Cuvettes, Cuvettes in Delhi, India.

Disposable Plastic Spectrophotometer Cuvette:-

1.) 4ML ( Cuvette, PS)

2.) 4.5ML (Cuvette, PS)

We are offering incubator, incubatorsstandard double wall fabrication. inner chamber made of out of richly anodized aluminum of highly polished stainless steel sheet and outer made out of thick mild steel sheet finished in white staving enamel paint or mat finished pestle color combinations. The gap is filled with special glass wool for temp. Insulation double walldoor with double glass window for observation in the chamber. Temperature range 5 c above ambient to 80c 2c controlled by a thermostat l - shaped thermometer is provided for taking temp readings. panel is provided with piolet lamps for mains& heaters, on-off switch, temp. Control' knob etc. The equipment is workable on 220 v ac 50 hz single phases. heating is achieved from 3 sides. Perforated all size in m.s. And s.s.

Product Description

We provide a proven range ofMeasuring Cylinders, which is fabricated from quality materials. The Measuring Cylinders are used to precisely measure out the volumes of objects for use in laboratories. Further, we offer Measuring Cylinders in various sizes and models to meet the requirements of our clients.