We are offering Hydraulic Press

accessaries for m.s. Trunk folding machine      v bar   bending hard blade   operate handle   pipe for bending round edge & locking clamp extra charge will be tacken.

Standard Supply:   Main Drive Motors Standard 'v' Block Pair of Foot Swishers  Electric Control Panel "INCH" & "SINGLE CYCLE", "DOUBLE CYCLE", "AUTO" mode of Operation Fine Stroke adjustments Rod with Limit Switches.   Machine Capacity (MS)   1 mm to 1.6 mm 3.25 mm 5 mm 6 mm 8 mm 10 mm   Machine Length   1500mm to 3050mm Length

We are offering shearing press

accessaries for m.s. Trunk folding machine   v bar 30 mm guisy for bending 16 gauge sheet bending hard blade operate handle pipe for bending round edge & locking clamp extra charge will be tacken.

cylinders   cylinders are made from precision honed carbon steel seamless tubes with hard cromed piston rods and international quality seals.   electrical control system   the electrical panal is mounted on right side frame. Electrical panal consists of motor start-stop push buttons, operation made selector switch with engraved indication, overload & ram up-down indicators and emergency stop button, as per general industrial electrical standards.   operational controls   press brakes having three operational cycles with operators high convenience & least fatigue by means of selected from the panel door mounted selected switch.   inch cycle   this ccle is used for etting bed angle and depth of stroke. The ram movement(up-down) can be controlled at any desired position from foot swiches.   singe cycle   once the cycle is stared, the ram completes one cycle (approach-pressing and return) and stops at the top end position.   auto cycle   the cycle (approach-pressing- return) is coninuously repeated once this cycle is selected. This mode is useful for continuous repetitive work where in stroke length can be adjusted to suit the job and the operator's speed. ram stroke movement is controlled by three limit switches. middle switch changes over the down ward speed of ram from approach to pressing speed. lower switch sets the lowermost position of ram with fine adjustment. on return, top limit switch stops the ram at top end position or stats next cycle.

We are offering Hydraulic Press

accessaries for m.s. Trunk folding machine      v bar   bending hard blade   operate handle   pipe for bending round edge & locking clamp extra charge will be tacken.

Standard Supply:   Main Drive Motors Standard 'v' Block Pair of Foot Swishers  Electric Control Panel "INCH" & "SINGLE CYCLE", "DOUBLE CYCLE", "AUTO" mode of Operation Fine Stroke adjustments Rod with Limit Switches.   Machine Capacity (MS)   1 mm to 1.6 mm 3.25 mm 5 mm 6 mm 8 mm 10 mm   Machine Length   1500mm to 3050mm Length

We are offering shearing press

accessaries for m.s. Trunk folding machine   v bar 30 mm guisy for bending 16 gauge sheet bending hard blade operate handle pipe for bending round edge & locking clamp extra charge will be tacken.

cylinders   cylinders are made from precision honed carbon steel seamless tubes with hard cromed piston rods and international quality seals.   electrical control system   the electrical panal is mounted on right side frame. Electrical panal consists of motor start-stop push buttons, operation made selector switch with engraved indication, overload & ram up-down indicators and emergency stop button, as per general industrial electrical standards.   operational controls   press brakes having three operational cycles with operators high convenience & least fatigue by means of selected from the panel door mounted selected switch.   inch cycle   this ccle is used for etting bed angle and depth of stroke. The ram movement(up-down) can be controlled at any desired position from foot swiches.   singe cycle   once the cycle is stared, the ram completes one cycle (approach-pressing and return) and stops at the top end position.   auto cycle   the cycle (approach-pressing- return) is coninuously repeated once this cycle is selected. This mode is useful for continuous repetitive work where in stroke length can be adjusted to suit the job and the operator's speed. ram stroke movement is controlled by three limit switches. middle switch changes over the down ward speed of ram from approach to pressing speed. lower switch sets the lowermost position of ram with fine adjustment. on return, top limit switch stops the ram at top end position or stats next cycle.